Search Documents

Development of a Froth Dropback Measurement Device

Sep 13, 2010

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the &quot;carbon monoxide ratio&quot;) it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure&#183; indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner&apos;s safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller&apos;s successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5&apos;F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984

By J. M. Tannenbaum

A depth-sensing micro-indentation technique is developed for evaluating mechanical properties of materials at elevated temperatures (to 1200°C). System description and design considerations of the test apparatus are described. Based on Hertzian spherical indentation approach, the micro-indentation test apparatus is capable of determining Young?s modulus and creep strength of test materials with flat, tubular, or curved architectures from room to 1200°C under either air or controlled gaseous environments. Calibration tests were conducted on a H13 Tool Steel coupon from 22°C to 500°C and single crystal Haynes 230 alloy at 1000°C with excellent agreement to the literature values. Indentation creep tests of Haynes 230 alloy were carried out at 1200°C with preliminary results showing good correlation to creep exponents. Further system refinements will be investigated, and additional testing will be conducted.

Jan 1, 2010

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By Masaki Imamura

A novel hydrometallurgical process for copper concentrate treatment has been developed by Niihama Research Laboratories of Sumitomo Metal Mining Co., Ltd. The process has numerous advantages with respect to the operational and environmental aspects. For example, copper is leached effectively from chalcopyrite concentrates by chlorine gas under atmospheric pressure. The copper in the leach solution is then separated from iron and silver by solvent extraction and undergoes electrowinning for its recovery as a highly pure copper metal; this does not require any further purification. Moreover, iron metal can be produced from the purified raffinate by electrowinning without generating a large volume of goethite or hematite, which are solid wastes generated due to iron rejection in common hydrometallurgical processes. This process can also realize the efficient recovery of precious metals. The results of batch testing and continuous-operation testing are presented in this paper.

Jan 1, 2006

By Edward F. Oxford

The area described in this paper lies along the inner margin of the Coastal&apos; Plain in Twiggs County, near the exact center of the State of Georgia. Twiggs is one of four counties which produces approximately 75 per cent of the nationals output of kaolin used in the paper trade. In this vicinity the land surface is characterized by coastal plain hills with elevations ranging from about 250 feet, above mean sea level in the flood plain of: the Ocmulgee River to about 550 feet above mean sea level on the hill tops. Surface drainage in the area is southwestward to the Ocmulgee River, the tributaries of which have dissected the land surface exposing thick sections of the upper parts of the hills of Eocene (Ocala Limestone and Barnwell formation) limestone, sand, marl and clay, and in the lower parts of the hills Cretaceous (Tuscaloosa Formation) kaolin, kaolinitic clay, sandy clay, sand and, gravel. The contact between these two principal groups of geologic units is rather easil distinguished as the top of the kaolinitic beds. It is described in detail and mapped in published geologic reports for the area (LaMoreaux, 1946).

Jan 1, 1968

By Mohammad Ranjbar, Zahra Manafi, FAZAELIPOOR MOHAMMAD HASSAN, HAMGHAVANDI MOHAMMAD RANJBAR, Mahin Schaffie

Bioleaching has an increasingly important place among available mining technologies as biological processes have emerged as alternatives for metal recovery, especially for metals like gold and copper. An important disadvantage of bioleaching is the slow reaction rates, with microbial attack times often lasting weeks. Therefore, applicable research is required to improve these rates. From previous research, copper bioleaching has been divided into two specific regimes: (1) surface reaction controlling step and (2) mix of surface reaction and diffusion controlling steps. The presented model, which includes the effects of both these regimes, predicted the results of copper bioleaching recovery with good accuracy.

By Mohammad Ranjbar Hamghavandi, Mohammad Ranjbar, Zahra Manafi, Mohammad Hassan Fazaelipoor, Mahin Schaffie

The present study introduces a new approach to understand the copper dissolution rate and to find an adapted mathematical statement for particle shrinkage rate in a batch bioleaching system. Four size classes of a chalcopyrite concentrate, namely [D1 : (−54 + 44)μm, D2 : (−44 + 38)μm, D3 : (−38 + 25)μm and D4 : (−25)μm], were used in the batch bioleaching tests by applying a mixed culture of moderately thermophilic microorganisms. The pulp density and temperature were 8 (%w/v) and 50 °C, respectively. Findings delineated that the bioleaching time can be divided into two specific time intervals: first, the surface reactions were the prevailing controlling step; second, the prevailing mechanism was diffusion through the product layer, whereas the overall rate of the process may be related to both through a Q factor using a mixed model. A mathematical model was developed based on particle size distribution (PSD) and a kinetic model. Experimental validation of the mixed model was accomplished by the representative sample with d80 = 54 microns. Results showed that the PSD of the specific sample was in good agreement with Rosin–Rammler function. Besides, the simulation result of the conversion fraction had the best conformity with the experimental data (with a maximum error of approximately 7%). This paper should be considered as an initial part of a larger, global model for chalcopyrite concentrate bioleaching.

By Zhongxue Li, Cuiping Li, Xiaoyun Hu, Yiqing Zhao, Huaying Wang

"Under the auspices of World Federation of Engineering Organizations’ Committee on Engineering and the Environment (WFEO-CEE) and Society for Mining, Metallurgy and Exploration (SME) Task Force on Sustainability and Mining (TFSM), and aimed at helping raise global understanding on and promote capacity building of risk management, this paper presents a framework and prototype of toolbox or knowledge warehouse for facilitating the application of risk analysis, mitigation and management techniques (RAMT) in the mining and minerals sector. The conception, design and implementation of the intended system of knowledge warehouse of risk analysis, mitigation and management techniques (KWoRAMT) are outlined. The system architecture of KWoRAMT is based on a browser/server (B/S) structured platform with web oriented interfaces and composed of data base, knowledge warehouse, searching mechanisms, and risk assessment methodologies. The knowledge sources for KWoRAMT will come from the TFSM expertise and Internet, including laws and regulations, codes of practice, standards, guidelines and best practices. The functions and outcomes of KWoRAMT consist of guided navigations with web links, categorized risk tools, annotated best practices with cases, and integrated risk approaches and solutions based on typical risk methods. Risk categories include those impacting on mine safety, mine occupational health, and mine community environment throughout the whole of mine life cycle from exploration, construction, and exploitation and processing to post-mining closure. Mining associated hazards will be identified and linked by vulnerability onto risk receptors through pathways. Risk management techniques for assessing impacts and consequences of mining induced hazards will be categorized with their pros and cons or strengths and weaknesses. Best practices and significant cases including experiences and lessons with problems, solutions, and recommendations on how solutions would be derived will be illustrated. Integrated risk approaches based upon typical methods will be developed for alternatives and actions."

Jan 1, 2014