Search Documents

By Roberto Galery, Priscila Esteves, Braz Cardoso, Marcelo Stopa

"It was developed in this work a computational tool to aid in anomaly detection present in the operation of ball mills. The tool uses a torque estimator that is based on measurements taken exclusively in the drive motor. The ball mill equipment widely used in the mining industry has, inherent to its principle of operation, high energy consumption and low efficiency. These characteristics are accentuated when the mill operates outside the ideal conditions of velocity and loading. Direct measurement of these variables is extremely difficult because it requires the installation of sensors in moving parts of the mill. Thus, systems that can help monitoring the operating conditions and predict anomalies are useful because they contribute to improving the performance of the process, help to reduce the energetic consumption, wear on the mill surface and frequency of maintenance shutdowns. The detection strategy implemented in this work is based on the fact that operational anomalies such as an inadequate percentage of balls and incorrect angular velocity manifest itself as a change in spectral components of the torque signal in the mill driven by an electric motor. The mill torque was estimated by processing motor variables measured by sensors commonly used for control purpose and installed exclusively in the motor. The mill was operated at various fault operating conditions and signals from electric motor and vibration on the mill shaft were measured. The spectral components present in the estimated torque signal were then compared with signals from a vibration sensor in order to establishing a correlation with anomalous operation condition of the mill. The experimental results showed that the signals obtained has an excellent correlation with other variables obtained by direct measurement and have potential to be used to construct a system for automatic fault detection in the operation of ball mills."

Jan 1, 2014

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By Pierre Marcotte

Jackleg rock drills expose their operators to high hand-arm vibration levels. To address this problem, an antivibration handle has been developed. The antivibration properties of the handle were achieved through a suspension based on a hinge design, achieved with a torsion spring and o-rings. To provide some bench marking for this new handle and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. Testing of four antivibration handles on the test bench have shown reductions of the overall weighted acceleration level in the order of 54 % to 60 %, with most of the attenuation occurring in the zh-axis at the rock drill percussion frequency.

Jan 1, 2008

By Fawcett M

Pine Creek Goldfields Limited (PCG) is rehabilitating the Enterprise Pit to an aquatic habitat and potential water resource. This paper discusses the development and implementation of that plan. Pine Creek Goldfields Ltd's Enterprise Mine is located approximately 230 km south of Darwin. Open cut mining of the orebody commenced in 1985 and continued for eight years with 14 million m3 of ore and overburden extracted. Geochemical testing of exposed rock types in the pit has demonstrated a propensity to produce acid, and dissolved metals. A plan of management has been developed and implemented to minimise the risk of acid formation and improve the overall water quality in the final void. In developing the plan prime consideration was given to reducing the potential for pit water to impact upon the regional groundwater. An interception system was constructed on Pine Creek to divert approximately 9 km2 of upper catchment into the northern end of the Pit. Construction of the diversion system was completed in December 1993 and a comprehensive surface and groundwater monitoring program initiated. The monitoring program and associated studies are also discussed.

Jan 1, 1994

With increasing demand for real-time monitoring of mine parameters, the requirement for appropriate data management in many mining applications is also increasing. This includes atmospheric monitoring in underground coal and metal mines. Although a number of different (real-time) monitoring systems have been installed in underground mines, they all typically share the same systems or sub-systems, where each sub-system may include both custom hardware and / or software components. In addition, monitoring components installed in underground coal mines in the USA should also be intrinsically safe and approved by the US Mine Safety and Health Administration. Real-time analysis adds complexity to the system since data validation and storage should be completed independently of filtering, data reduction operations, or visualization. Real-time processing may include statistical evaluation, trending, cross-correlation, and real-time alarm or warning generation. This paper presents the concept and design of an integrated system under development for atmospheric monitoring in US coal mines.

Jan 1, 2014

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

By Dennis P. Martin, Michael M. Fitz, James E. Friant

Methods for reducing the cyclic nature of drill and blast tunneling operations have been long needed. A miniature blasting system using 10 mm (.375 in.) holes, 0.91 m (36 in.) deep, and blasting only one hole at a time makes it practical for men to work behind a shield, remaining at the face during the entire process. A prototype automated module was developed to drill, load the hole and initiate the detonation without moving from the hole. A unique cost effective gell explosive and a novel, low cost initiation method were developed.

Jan 1, 1989

By Kwang-Hyun Jeon

Recently, 3D printing technology in the manufacturing field is in the spotlight. In the construction industry, similar rapid prototyping technology that does not use conventional form can be applied to meet the demand on free formed structure that can provide aesthetic value and functionality. Conventional formwork can increase construction cost and period for various structure with complex shapes while it has numerous advantages such as high strength, convenience, accuracy and good quality of surface roughness. To meet the demand on free formed structure, automated freeform construction systems such as Contour Crafting and Concrete Printing have been developed with active collaboration between university and industry in USA and England. However, details on the system have not been fully released in public, so the possibility of its fusion and spin-off technology cannot be expected. In this paper, cost-effective solution for mechanical and control system for constructing a free curved structure without mold are described. As an appropriate material for the system, fiber reinforced mortar was selected by experiments on compressive strength, setting time and fluidity. After performing G-code simulation, transfer and extrusion experiments with the selected mortar mix were performed and the possibility of the development of automated freeform construction system was demonstrated. Based on this research results, it is required to keep the automated freeform construction system improve and extend it into the new application area in construction industry.

Aug 1, 2013

By Peter L. Swanson

NIOSH has developed an automated PC-based seismic monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network (LAN) is a central feature of the system. Design requirements include (1) the use of lowcost, off-the-shelf, data acquisition and computer hardware, (2) the capability of automatically merging waveform data sets from different types of monitoring systems, (3) delivery of raw and processed data underground and on the surface, as well as to remote sites, and (4) automated data collection and processing over long periods of time without the need for human intervention. Current mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface and provide 20 to 40 stations within a radius of several kilometers. Event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's hardware and software components, examples of installations in hard-rock and coal mines, and a few observations from western U.S. longwall coal mines.

By A. P. Page, G. E. Alexander, L. L. Sirois, A. A. Winer

A knowledge of the electrical surface characteristics of minerals is all-important in the choice of treatments to up-grade and beneficiate them. At their solid-liquid contacts, there are transfers of ionic species, which for insoluble oxide minerals are the H+ and OH-ions. The adsorption density of these ions can be detected by carrying out potentiometric titrations, and this paper describes the automation of such an apparatus. The details are discussed fully and the validity of the method is demonstrated by flotation tests.

Jan 1, 1969

By Robert R. Dorfler

We ought not look back unless it is to de- rive from past errors, and for the purpose of profiting by dear bought experience. - George Washington During the mid 1960's, the application of automation was introduced to Climax by two process control companies. In 1969 Climax decided to seriously consider improved control of selected areas of their milling process after preliminary research had been completed on two rougher ball mill grinding circuits. In 1971 the Climax Mill Department developed a direct digital control scheme for rougher milling, designed a remote control center for handling process water, planned to automate the central steam heating facility for energy conservation, and convert other plant areas to automation. All twenty rougher grinding mills and the industrial water system were automated by 1977. The idea of automating central heating and other areas was abandoned although some fuel conservation items were installed at the heating plant. During this period from 1971 to 1978, the mill capacity was expanded from 39,000 metric tons per day to 43,000 metric tons per day and cyclone classification was introduced to rougher milling. Ore quality changes degraded the milling recovery from over 90% to less than 85%. This report describes the procedure the mill used in developing the automatic process and the occurances that affected the timing and fina1 control logic. The report deals primarily with the automation of the ball mill grinding, classification and flotation process as this was the bulk of the seven-year project.

Jan 1, 1979

By Hidenori Okamoto, Katuto Itoh

"Nippon Mining & Metals' Hitachi Refinery refines 40% of the anodes produced at its Saganoseki Smelter & Refinery. Its current annual production stands at 180,000tons.The refinery always endeavors to increase productivity. One of the outcomes of its efforts is an originally developed automatic short-circuit detector used to inspect short-circuits between anode and cathode. The detector is designed to inspect the 56 pairs of anode and cathode in a cell by fluxgate sensors at once. It inspects 564 cells, automatically and un-manned, and gathers data to be put into a computer. The development of the detector led to a reduction of man-power and achieved a detection accuracy superior to that of a hand-held gauss-meter. In addition, statistical and historical processing of the data enabled early detection and early recovery of the cells with poor efficiency.The new system also contributed to raising the refining capacity and reducing the unit steam consumption, because it is possible to inspect even the cells covered with thermal insulation sheets.IntroductionInspection of cells is an important component of the operation management of a tank-house. At the Hitachi Plant, it used to be carried out by two workers who walked on and checked all the cells of its tank-house once a day to find out any short-circuits in the cells, using hand-held gauss-meters. They inspected about 33 thousand pairs of cathodes and anodes a day and removed nodules by hammers. This method had following problems:it needed much manpower.the walk on the cells sometimes deranged electrodes positions.there was radiation-loss connected with the inspection due tothe fact that the workers were obliged to uncover thermal insulation sheets on the cells while inspecting."

Jan 1, 2000

By K. N. Mayfield, T. Novak

"The applications for automation continue to expand within the mining industry. These applications can range from the startup, control, and shutdown of processing plants to the autonomous operation of surface haulage trucks. However, the term “automation” should not necessarily be interpreted as the total elimination of human interventions since numerous mining processes can be partially automated. The future survivability of many mining operations will be influenced by a company’s willingness and ability to understand, accept, and utilize this technology. The mining workforce, including management and engineering, should be familiar with the technological capabilities and limitations for effectively implementing automation into mines for improving safety and productivity. The Department of Mining Engineering at the University of Kentucky has recognized this educational gap and developed an automation laboratory, along with project-oriented courses at the undergraduate and graduate levels. The laboratory and the course objectives are described in this paper, as well as the skills and abilities that students obtain at the completion of the course(s). BACKGROUND The touted benefits of automation include: improved productivity, lower operating costs, reduced drudgery of repetitive operations performed by workers, and the removal of workers from hazardous locations. The acceptance of advanced technology by the mining industry, however, has traditionally been slow. This cautious approach is understandable considering the complex and harsh conditions routinely encountered in mining operations. Bad experiences with some premature installations of newly hyped technologies may have also resulted in lingering skepticism by many mine operators. Nonetheless, with thoroughly demonstrated reliability and proven applications, automation based on programmable logic controllers (PLCs) has made significant inroads into the mining industry. Programmable logic controllers (PLCs) are the workhorses of automation. They were originally conceived in the late 1960s, long before the invention of the personal computer (PC). Initial PLC applications were directed towards sequential relay control in manufacturing plants, which subsequently eliminated the use of “relay logic” that was based on hard-wired electromechanical relays. With continuous advancements in electronics and computer technology over the years, PLCs have evolved into sophisticated and powerful devices with very stable operating systems. They are designed for deterministic logic execution with extreme consistency in timing, along with a high tolerance to temperature, humidity, and vibration (Smith 2003). Because of their robust characteristics, PLC networks now provide the backbone for most industrial automation applications."

Jan 1, 2017

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By M. Bourassa, R. del Villar, S. St. Arnaud, J. Valenzuela

"Autogenous grinding is used quite frequently for mineral comminution as a result of its lower capital and operating costs. However, it is more difficult to control than conventional grinding, particularly when the autogenous or semiautogenous mill is the only comminution stage (i.e. no secondary grinding is available). Analysis of the control strategy used then becomes extremely important, a task that is greatly simplified by the use of an empirical dynamic simulator:This paper presents the methodology used in the development and the calibration of such a simulator for the autogenous grinding circuit of an iron are concentrator: The various steps are described: industrial data acquisition, preliminary treatment of the gathered information. and empirical modelling of the process. Finally, both the actual and the proposed control strategies are compared using simulation results.This exercise has shown that the variability of some of the controlled variables could be reduced through a better handling of the water addition and the use of filters on some of the signals used for control purposes. The reduction in variability of critical variables, such as power draw, would allow their average value to be increased without the risk of exceeding their safety values. Some advanced control techniques were also tested, with interesting results."

Jan 1, 1995

By P Gilroy

In recent technical investigations that were triggered from ore for rail shortfalls at Yandi, BHP Iron ore has identified a gap in resource knowledge relating to geo-metallurgical characteristics that predict materials handling performance and throughput. Within these investigations BHP has learnt that this lack of resource knowledge has translated to a lack of predictability associated with mine planning inputs which has resulted in poor compliance to plan and deviation management practices. A business value chain was developed in an attempt to identify the best possible solution to unlock this resource knowledge in the short, medium and long term planning horizons. A fast fail approach was taken with the implementation of hyperspectral blasthole analysis, which was chosen to deliver the best possible value driver for the asset. This report will detail the Yandi journey in expanding the hyperspectral and geo-metallurgical value chain, unlocking resource knowledge along the way. CITATION: Gilroy, P, 2018. Development of an empirical geo-metallurgical model that unlocks value of the mineral resources at Yandi Mine, in Proceedings Complex Orebodies Conference 2018, pp 85–87 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Voigt, B Bolton, C Rumble

The Ok Tedi copper and gold mine is owned and operated by Ok Tedi Mining Limited (OTML) and is located in the Star Mountains of the Western Province of Papua New Guinea. Waste materials (both sulfidic and carbonate materials) from mining operations, comprising 55 Mt of waste rock and 31 Mt of tailings per annum, are discharged into the headwaters of mine area creeks where erosion and sediment transport carries significant proportions of the total waste into the Ok Tedi and Fly River systems. The tailings are potentially acid forming (PAF) while the waste rock has been strongly acid consuming with an excess of acid neutralising capacity (ANC) due to the high proportion of limestone waste. Tailings and waste rock are eroded into the river system and transported to the lower Ok Tedi and floodplains where deposition takes place. Because of concern due to vegetation die back, a dredging operation commenced in March 1998 to remove the sand fraction from the main river channel. OTML identified a potential future ARD risk from the stockpiled sands due to reduce limestone production at the mine and sulfide/carbonate mineral segregation in the river system and in the dredge sand stockpiles. This paper describes the structure and framework of an empirical model developed to assist OTML in planning ongoing mining operations to control ARD. Modelling identified the need to provide additional mined limestone to prevent future ARD generation from material deposited in the mine area creeks. With the additional limestone, the ARD risk in waste rock storage areas and in the Ok Tedi and Fly River sediments is predicted to remain low due to the combined effects of high ANC, high alkalinity of natural waters and high moisture contents (mostly fully water saturated). However, monitoring and modelling indicate that the ARD risk from the stockpiled sands will increase substantially during the remaining years of the operation. OTML have initiated programs to identify and evaluate options to mitigate this risk.

Jan 1, 2003

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007