Search Documents

By H. L. Zimba

Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank or at any time in a batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume or a relative concentration, which will be a function of the recovery. A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the collected data. The data used in this paper were collected from bench-scale flotation tests on Konkola primary mill cyclone overflow at various pulp densities and pre-flotation thickener underflow at a pulp density of 35% solids by weight.

Jan 1, 2009

By S. M. Bulataovic, D. M. Wyslouzil

"The Martison Lake phosphate-niobium deposit is composed of unconsolidated residuum containing clay and silt-size particles of phosphate, niobium, iron and clay minerals. This paper deals with the laboratory and pilot plant development of the flowsheet and the reagent scheme to treat the Martison Lake ore. The ore, in addition to the complex gangue composition, contained several phosphate minerals including fluorapatite, francolite and florencite. The detailed laboratory and pilot plant evaluation resulted in the development of an effective flowsheet and reagent scheme for the selective flotation of phosphate minerals using a fatty acid circuit, followed by niobium flotation using amine collectors at acid pH. The developed flowsheet included des liming of ore, magnetic separation, and selective P 2 O 5 -Nb 2Os flotation. The main aspects discussed include characterization of the ore, step by step development of flowsheet and evaluation of dfferent modifiers and collectors for P20s and Nb20s flotation.INTRODUCTIONMartison Lake phosphate-niobium ore deposit, located 75 km north of Hearst, Ontario was discovered in the early 70's and has been the subject of extensive technical-economic evaluation in the late 70's and early 80's.The deposit is covered completely by 30 m to 90 m of glacial overburden and is composed entirely of unconso1idated material called residuum, that lies on top of a precambrian age carbonatite intrusive from which the residuum was derived by weathering and natural leaching in situ. The residuum is and irregularly-shaped horizontal lens, 2 km by 3 km in area, and up to 100 m thick, composed mostly of unconsolidated clay and silt-size particles of phosphate, niobium, iron, mica and clay minerals."

Jan 1, 1986

By Ö. Y. Gulsoy, L. Ergün, I. B. Celik

"In this study, the studies to develop a flowsheet for a low grade chromite ore are presented. The existing concentrator had to be suspended due to the decreasing metal prices. The study commenced with mineralogy and liberation profile of the chromite. The valuable mineral is chromite and the major gangue mineral is forsterite together with small amount of brucite and calcite. Heavy liquid tests were performed on different size fractions without any acceptable success. The concentration tests were performed using teetered bed separator (TBS) +shaking table, spiral concentrator+TBS+shaking table for different grind size. Based on the test results, 100% finer than 0.4mm was found to be optimum for grind size. Comparison of alternative circuits showed that the performance of both alternatives would be similar. A flowsheet was designed and operated for as 25 tph trial circuit in the existing plant. The results showed that the performance of the plant predicted was very close to the actual plant data. The paper describes the methodology used, presents the experimental data and actual performance figures.INTRODUCTION Turkey is one of the largest chromite producers in the world. Since 1850, chromite mining found industrial applications and geographically spread along six different regions in Turkey. Although the reserves in these locations are not as rich as the big producers, they are regarded as very valuable due to Cr/Fe ratio in terms of chromite utilization standards (1, 2). In this period, significant portion of high grade (=35% Cr2O3), directly marketable ore deposits have already been produced. According to General Directorate of Mineral Research and Exploration (Turkey) data; 83% of the known chromite deposits of Turkey which makes 242 341 000 tons in total, is consisting from the deposits those have a Cr2O3 grade lower than 10%. Only 5% of the known deposits (13 087 000 tons) has a grade of directly saleable (2, 3). Gravity concentration methods are well-known processes for chromite beneficiation and there are plenty of plants in the world and Turkey using these methods. As different equipment combinations can be used for the same enrichment method, different methods can also be used in combination for plant designs (4). Beneficiation of low grade and problematic chromite ores may lead to use these method and equipment combinations (5, 6). Ore liberation, the grades of Al2O3, SiO2, FeO and Cr2O3 in the obtained concentrate, Cr/Fe ratio, some physical and chemical properties between gangue and minerals (i.e. specific gravity, magnetic property, color, etc.) designate the selection and combination of these methods and equipment (7)."

Jan 1, 2017

By Luis E. Vallejo

Experimental and theoretical analyses are presented to study the mechanics of growth and interaction for three inclined left-stepping, three inclined right-stepping and two inclined non-stepping cracks in a brittle material subjected to uniaxial compression. It was found that the non-stepping cracks did not interact and they propagated individually in a direction parallel to the uniaxial compressive stress. The propagating cracks formed in regions where tensile stresses developed. The left-stepping cracks interacted and formed branching cracks as a result of failure in tension of the material between them. Also, they propagated from their tips in a direction parallel to the uniaxial compressive stress. The right stepping cracks did not interact, but extended themselves from their tips following a direction parallel to the uniaxial compressive stress. The extended cracks formed in areas of compressive stresses.

Jan 1, 1984

By Ulf Marklund, Stig Markstrom

Pioneering work with pilot scale autogenous grinding started in Boliden 1956. From 1961 to 1991 eleven fully autogenous grinding (AG) circuits have been installed at various concentrators within the Boliden company. A compact two-stage grinding system was de- signed in the beginning of 1970s. The system included a pebble extractor which feed the secondary grinding stage with grinding media. The APC grinding system (Autogenous/Pebble/Crusher) is a further development of the AG concept. A new design of the Boliden pebble extractor together with improved control strategy make the performance of the APC system suitable to almost any ore quality. The Boliden AG concept is probably the most cost efficient grinding system of today.

Jan 1, 1998

Control of flotation processes is mostly managed by plant operators, who assess the performance of the plant based on their own experience and other heuristic rules. These rules tend to be subjective or ill-defined, since most of them are concerned with the structure of the flotation froth, such as colour, bubble size and shape distributions, froth mobility and froth stability. These phenomena are very difficult to quantify objectively, and inexperience on the part of the operators, human error, etc., can lead to significant inefficiencies in plant operation. In this paper the development of a fuzzy system to support the control decisions of plant operators is described, which leads to significantly smoother control action and more stable plant operation than could be obtained with crisp sets of rules or manual control strategies. Keywords: flotation, fuzzy logic, image analysis, genetic algorithms, rule induction

Jan 1, 2000

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

Geomorphology is one of the most basic elements in geographic enviroments. Geomorphological mapping is significant in the spatial distribution of representing land form and understanding various features of geomorphology. Geomorphological mapping began very early in China, as the map, showing conekarst(karst pinnacles) of Juiyishan, Hunan province, it was drawn in 168B.C., which was excavated from Han tomb. Mawangdui, Changsha. Its original idea of map-making is rather similar to that of modern map and could undoutedly be the oldest map of tropical karst discovered in the world.Before liberation, landform mapping was done piecemeally and only a small number of maps were prepared by a few editor as insets.

Jan 1, 1990

By Hamid Maleki

Mining in the Book Cliffs Coal Field of Utah has historically been associated with seismicity because of high-stress environments and the presence of stiff, competent rocks. Recognizing the geotechnical risks in this coal field, mine engineers have dedicated considerable resources to the study of mine seismicity. In spite of these efforts, there are no engineering procedures for assessing mine seismicity for a new property and in developing mine designs. This paper presents the results of ongoing geotechnical monitoring and stress analyses at a western U.S. coal mine. The intent is to demonstrate the application of geotechnical methodologies in evaluating mine seismicity and stress-control technologies including evolutions in yield pillar designs for variable topographic conditions of the Book Cliffs Coal Field. We show that narrow yield pillars are quite effective in limiting strain energy accumulation along the gateroads and thus the potential for pillar seismicity. At the same time, the pillars provide sufficient resistance to control roof-floor convergence at the headgate, gradually unloading to residual strength inby the face position. Lagging, nonuniform caving of overburden rocks results in periodic stress concentrations at the tailgate comer. The sudden release of strain energy triggers sudden failure of critically loaded coal in this area of the high stress gradient. The three-entry gate pillar configuration promotes formation of long cantilevers and load transfer to the tailgate, contributing to formation of cutters and coal bumps. The source of seismicity is investigated while simulating slip along three sets of joints in two stiff stratigraphic units during multipanel extraction.

Jan 1, 2003

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Elena L. Chanturiya, Vladimir A. Bocharov, Roman A. Amosov

"In many volcanogenic base metal deposits of Russia the gold is closely associated with copper sulphides and pyrite. The recovery of gold associated with pyrite is especially difficult problem.Investigations of gold chemical state and mineral forms in copper-zinc sulphide ores of Gay and Barsuchiy Log deposits in the Urals have been made using EPMA, optic image-analysis, XRA, SEM, thermo-electrical force measurements and selective gold leaching experiments.Two gold varieties are determined: 1) free native gold particles (from 5 µm up to 0,25-1,0 mm), which can be liberated after grinding of ore up to 0,074 µm and named “free gold”; 2)”invisible” gold, including finely disseminated native gold and chemically bound gold. The second variety can’t be disclosed during grinding. Free gold can be recovered by gravitation and flotation while the processing behaviour of “invisible” gold is determined by properties of gold-bearing sulphides: pyrite and chalcopyrite. According to results of diagnostic leaching experiments in ores of deposits mentioned above the part by weight of free gold reaches 70%, the part by weight of the ”invisible” gold is up to 20%. About 10% of gold is enclosed in quartz and acid-soluble minerals.Theoretically (taking into account gold distribution data) it’s may anticipate gold recovery by gravitation up to 60%. However after grinding up to 50-60% of class –0,074 mm only about 40% of gold passes into oversize product including 30% of free gold and 8% of ”invisible” one. It can be recovered by gravitation. Remaining free gold and ”invisible” gold can be extracted by flotation – 25% in total. Inevitable gold losses in tailings may reach 8-10%."

Jan 1, 2003

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By Gary Pattrick

A new class of spongy Au catalysts is studied for the selective catalytic reduction of NOx by propene under leanburn conditions. The spongy catalyst is an unsupported powdered Au that consists of micrometer particles (~5 microns) that have nanometer scale (~10 nm) internal skeletal structures. The effects of alloying 1 ? 50 atom % platinum group metals (M= Pt, Pd, Rh) and 5 wt% first row transition metals (M = Ti, Mn, Fe, Co) were studied. Even low additions of PGMs (1 at.%) cause significant shifts to lower temperature regions of activity and the largest shift is obtained for Rh. For Rh this is interpreted as a strong synergistic interaction between Rh and Au. Possibly related to the Rh effect, Co is the only other metal studied that lowers the temperature of NOx reduction. The other first row transition metals inhibit the reduction reaction.

Oct 1, 2003

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997

By R. S. Archer

IN the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the heat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis; heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while iii others, especially ill those whose grain is unusually fine or in which the final hardening heat, has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters.

Jan 1, 1919

J. A. MATHEWS, * Syracuse, N. Y. (written discussion?).-The reagent described by Mr. Archer seems to be a selective reagent, useful in one particular field. Nevertheless, the field is one in which it is likely to prove of considerable value, because there is a great deal of alloy steel FIG. 1.-ETCHED 1 HR. IN ARCHER'S FIG. 2.-ETCHED 1 HR. IN ARCHER'S REAGENT. PLOD 60. X 188. REAGENT. IZOD 10. X 188. heat-treated to approximately the properties mentioned in the paper. If it is found, by further tests, to be applicable to a wider range of compositions than merely chrome-nickel steels, for the most part discussed by Mr. Archer, its value will be thereby increased to just the extent to which it can be applied. In view of the fact that certain of these chrome-nickel steels, very similar in physical properties and hardness, show very different results in the Izod or notch test, and in view of the fact that when such differences are noted in the fracture the brittle steels usually

Jan 5, 1919