Search Documents

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1988

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By S. A. Hosseini, O. Asghari

"Recoverable mineral resources assessment has become a standard geostatistical application in the mining industry, with various geostatistical techniques currently available. This investigation aimed to improve the prediction at the Sungun deposit and to obtain mineral resource models capable of handling (i) the change of support from drill-hole composites to selective mining units (SMUs), (ii) the multivariate nature of the ore control selection criteria that involves both copper and molybdenum grades; and (iii) the local uncertainty on the true (unknown) grades. The solution presented in this paper is to use direct block-support sequential cosimulation in order to construct a set of alternative outcomes of the copper and molybdenum grades on block support over the deposit, with no need for storing point-support values, hence with a considerable gain in memory management and CPU time. The grade realizations so obtained are then processed to calculate the uncertainty in the mineral resources that can be recovered above given cut-off grades, both globally and on a blockby- block basis. IntroductionGeostatistical methods are widely used by mining companies to determine a resource model of the tonnage and head grade of a potential orebody, which is one of the first and most critical inputs underpinning any mining project. The prediction of the grade, tonnage, and recoverable metal for a particular mining plan and the corresponding financial forecast constitute the main technical risks in mineral resource evaluation. The conventional approach to this problem is to predict the mineral grade for constant volumes relevant to the mining plan and to base the recoverable mineral resource calculations on those predictions. Alternatively, one can directly predict the local variability in the mining block grades based on a spatial distribution model (David 1988; Rossi and Deutsch 2014). Multiple realizations can also be constructed by conditional simulation, providing a more complete representation of block grade uncertainty, as well as the uncertainty over multiple blocks. Simulation methods allow quantification of the uncertainty of the mineral resource prediction risks in downstream studies such as mine design, mine planning, or operational optimization studies; the risk assessment is achieved after applying transfer functions to the conditional simulation models (Dimitrakopoulos 2012; Rossi and Deutsch 2014)."

Jan 1, 2017

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By C. Flores

The direct cementation of copper from a loaded D2EHPA 20 % vol. in kerosene using zinc, zinc-lead alloy and iron metallic powders was studied. Copper was loaded into the organic solvent from an aqueous copper sulfate solution. Results indicated that copper is reduced spontaneously with relatively fast reaction rates. The effects of several operating parameters such as water content in the organic system, initial copper concentration, reductant surface area, oxygen and nitrogen atmosphere, intensity of the agitation and temperature on the galvanic stripping of copper were studied. For a better understanding of the electrochemical reactions involved in the galvanic stripping, the dissolution of metallic copper in the organic solvent was also studied. Copper did not dissolve unless a small amount of water was present in the organic system. The results and possible reaction mechanisms are discussed.

Jan 1, 1999

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

Comalco's Bell Bay smelter produces some 94 000 t.p.a. of primary aluminium in the form of foundry alloys, extrusion billet and rolling blocks. The extrusion billet and rolling block are produced by a process, in which molten aluminium is poured into an open ended water cooled mould of the required shape. The bottom of the mould is initially closed off by a dummy or starting block. Primary cooling takes place at the mould wall and secondary cooling is achieved by direct water sprays onto the out side shell of the product. Careful preparation of the molten alumin- ium is essential if stringent alloy specific- ation limits are to be met. Optimum casting temperature must be maintained within a narrow range and metal cleanliness is important to ensure a consistent product. Increased demands of recent years for larger product and higher standards of surface quality and dimensional control have been instrumental in forcing improvements in furn- aces, casting machines and in mould and dummy Doq,

Jan 1, 1977

By M. H. Staia

A Venezuelan ilmenite concentrate has been chlorinated at a temperature of 700" C by carbon tetrachloride. In the experimental rig, built at laboratory level, the direct chlorination process yielded a TiCI, recovery of approximately 85% after 280 minutes processing. The partial pressure of carbon tetrachloride was nearly atmospheric (0.94 atm). Product vapors from the reactor were fractionally condensed in a condenser which was maintained at a temperature of 250°C meanwhile TiCl, vapors were condensed in refrigerated coils at a temperature of -20°C. The concentrate used in this investigation was obtained by applying gravitational and magnetic concentration methods to the black sands. The experimental results have shown the need to asses the influence of the weight ratio of ilmenite to carbon tetrachloride on the resultant products. The equilibrium of the heterogeneous system has been calculated taking into account the initial experimental conditions.

Jan 1, 1995

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By H. Keith Henson

The purpose of this paper is to describe the possible application of two relatively new technologies: flat load cells, and improvement seeking computer programs (referred to in the literature as heuristic programs); to a very old problem, inventors control of ball mills. The combination of these two technologies seems most applicable to grate discharge mills operated closed circuit. It is possible that other applications such as controlling the inventory of autogeneous mills might also be found. Direct control of ball mill inventory has been the goal of a number of investigators over many years. Many patents and articles on the subject have claimed success, but operating installations are hard to locate. An excellent review of the advantages and problems of direct inventory control is contained in an article by Oswald and Ziegler (1). Figure 1 is a conventional representation of throughput vs. inventory with other factors such as slurry consistency and rock twee held constant. There are common sense, physical arguments? and experimental evidence supporting the existence of a unimodel curve of this twee? though direct measurement of the shape is difficult and how it moves as rock type changes is riot well known. Figure 2 represents the problem faced by all mass measurements of inventory, a tare weight of about 25 time the inventory mass. Worse yet, the tare is variable due to ball and liner wear and the Periodic addition of balls. The problem then breaks down into two parts: 1) obtaining enough mass

Jan 1, 1977

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important alvantage. of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate: (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elim-ination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the thresthold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step copper smelting is still a process of the future.The paper describes the potential advan-tages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By P. Karimi, A. Akcil, A. Amini, H. Abdollahi

"In this study, cyanidation experiments were carried out on a massive sulfide ore sample, whose grades of the precious metals gold and silver were found to be 4.2 g/t and 311.9 g/t, respectively. Other elements in the ore were arsenic with average grade of 1,751.6 g/t; antimony, 619.7 g/t; zinc, 781.4 g/t; copper, 454.6 g/t; lead, 101.8 g/t; mercury, 324.3 g/t; and bismuth, 0.6 g/t. The first objective of test work focused on determining the best conditions for extracting gold from the ore, ground to less than 75 microns. Different influential parameters such as particle size fraction, cyanide concentration, pH and leaching time were investigated. The optimum parameters were found to be particle size fraction of less than 25 microns, cyanide concentration of 2,000 mg/L, pH of 11 and cyanidation time of 24 hours. In these optimum conditions, the highest gold and silver leaching efficiencies were 76.88 and 59.63 percent, respectively. In addition, roasting as pretreatment at a temperature of 700°C over a period of two hours was evaluated. Cyanidation testing of the roasted ore in the optimum conditions found increases in the gold and silver leaching efficiencies to 85.97 and 67.57 percent, respectively. Moreover, antimony extraction rose to 43.10 percent, from 23.73 percent without roasting.IntroductionGenerally, gold ores can be classified as “free milling” or “refractory,” depending on how they respond to cyanide leaching (La Brooy et al., 1994; Celep et al., 2009). While high gold recoveries (> 90 percent) from free-milling gold ores can be readily achieved, refractory gold ores are often characterized by low gold recoveries (50-80 percent) within a conventional cyanide leaching process (Rubisov et al., 1996; Adams, 2005; Celep et al., 2009). The presence of preg-robber components such as carbonaceous matter, sulfide minerals and aluminosilicate can further decrease gold and silver dissolution rates and recoveries. With the negative effect of the presence of preg-robbers, gold dissolution is considerably diminished in solutions with high cyanide concentration (Tan et al., 2005). In such refractory gold ores, gold particles may sometimes be occluded or included in the sulfide minerals, and pretreatment becomes necessary to break down the mineral structure to liberate gold for subsequent recovery. These ores are usually pretreated with an oxidizing process, after which gold and silver can be recovered by a standard cyanidation process. The main oxidizing processes available for refractory gold ores are roasting (LaBrooy et al., 1994; Angelidis and Kydros, 1995; Li et al., 2009; Karimi et al., 2010; Kyle et al., 2012), biological oxidation (Lawrence and Bruynesteyn, 1983; Komnitsas and Pooley, 1990, 1991; Deng and Liao, 2002; Ciftci and Akcil, 2010, 2013) and pressure oxidation (Mason, 1990; Murthy et al., 1992; Qingcui et al., 2009). In addition, ultra-fine grinding is being used in some plants for the liberation of gold and silver particles that are interlocked in the sulfide or silicate minerals (Celep et al., 2011)"

Jan 1, 2015

By R Paterson, A Christensen

The routine use of gravity gradiometry for the detection of orebodies with no outcrop is now being undertaken. The commodities and orebody styles range from banded iron ore formations to volcanogenic massive sulfide (VMS) style polymetallic deposits. This recent innovation of flying gravity gradiometry was pioneered by BHP Billiton and Lockheed Martin with the Falcon technology (Lee, 2001), and now two additional systems, also using Lockheed Martin instruments, are deployed. In South Africa, magnetic gradiometry is being developed and deployed with the same objectives in mind. In this case, a system from Institute of Photonic Technology (IPHT) is being used. The detectable wavelengths from such systems have decreased to less than 200 m in the last year, and it is expected in 2011 that wavelengths to less than 100 m, with anomaly signal strengths of less than 2 Eotvos for gravity gradiometry will be viable. The key to these advances lies in the improvements of processing software and geological modelling. In particular, methods using all the tensor components are starting to be routinely deployed to filter, level and grid the observed signal. These methods do, however, require full insight and understanding of the reference coordinate systems used by the various instrument designers and survey operators. The digital terrain models need also to be observed to an accuracy of better than 20 m cell sizes, using such techniques as Lidar. Then the terrain effects can be modelled. The topographic surface represents the largest and most proximal density contrast encountered in an airborne survey. Hence terrain effects can have significant impact on airborne gravity gradiometry data. A decorrelation of the terrain effect with the observed signal requires a method of best fitting with a regional surface density. A novel technique has been developed for this purpose. This technique uses a tensor algebra to estimate a density between 1 - 4 g/cc that explains the average observed signal. Armed with this result, the anomalous buried bodies can be revealed by subtraction.

Sep 26, 2011

By S. L. Huang

The location and shape of potential failure surfaces in soil slopes were directly determined based on the stresses induced in the soil mass and the strength of the soil itself. Stress calculations were carried out by the finite element method with the Drucker-Prager nonlinear material model. The Mohr-Coulomb failure criterion and Mohr's circle stress analysis were then applied to the calculated stresses to determine the characteristics of the failure surface.

Jan 1, 1989

An algorithm is described which leads directly to a unique set of coal washing parameters which, in two or more parallel streams, will give maximum yield of product at a given ash. This occurs when all parallel streams are washed to the same incremental ash. This strategy is shown to offer a considerable increase in yield compared to the simpler strategy of washing each stream to the same sumulative ash.

Jan 1, 1987

By Robert J. Gorney

This paper deals with the actual application of a direct digital control to simple as well as complex industrial process control loops, Fundamental descriptions of preliminary research and design are described briefly, as is the development of the present day controller and control computer. The results and effects of direct digital control in various types of single and cascaded loops as opposed to the use of conventional controls are discussed. Computer supervision of a process and control override are taken into account, in addition to methods of short and long term plant economic optimization.

Jan 1, 1965