Search Documents

Develop a cost-effective, flexible method for extinguishing underground coal mine Fires that can be readily used in fire conditions encountered in both abandoned mines and coal outcrops. In addition to the abatement of an underground coal fire, a secondary objective was to prevent subsidence by filling the voids with a material having sufficient compressive strength to minimize subsidence. Approach The Colorado School of Mines Research Institute was awarded a research contract to determine the viability of using Foaming Mud Cement for abating underground coal mine fires and preventing subsidence. The program consisted of a laboratory and pilot scale investigation and process development. An extensive, controlled test program was conducted simulating floor, rib, roof and rubble fire conditions. Field demonstrations were conducted after the pilot scale research was completed. How It Works Traditional techniques have targeted the control of burning by eliminating the air, fuel source or heat. This has been accomplished by trenching, quenching, mothering or combinations of these three methods. These techniques were not always successful, particularly in the case of fires in abandoned mines.

Jan 1, 1991

By J. J. Gusek

The Riley Pass strip mine is an abandoned uranium-bearing lignite deposit in Harding County, South Dakota, covering about 150 acres of highwalls, pit floor and mine spoils exhibiting elevated levels of radioactivity. Six reclamation design alternatives were developed, ranging from doing nothing to reclaiming to approximate original con-tour. The alternatives were evaluated for expense, site stabilization, and mitigation of public safety hazards. A comparative economic evaluation on three of the alternatives was completed for the Forest Service in selecting an alternative and substantiating federal funding requests. This evaluation included economic impacts associated with physical and radiologic health hazards, affects on recreational users, socioeconomic impacts and environmental improvement.

Jan 1, 1995

By Daryl L. Gusey, John T. Neubert, Matthew A. Sares

The Colorado Geological Survey completed an inventory of environmental degradation associated with abandoned and inactive mines on National Forest System lands in Colorado. In the course of the inventory, areas with naturally occurring acid rock drainage were also noted. Approximately 18,000 abandoned mine- related features were inventoried, including about 900 features that are considered significant enough environmental problems to warrant further investigation. Water quality data, such as pH and conductivity were gathered at all features where water was present, such as draining adits, seepage at the toe of dumps and tailings, and standing water in shafts. Samples were taken where field tests indicated low pH andlor high conductivity, including several areas with naturally occurring acid rock drainage. Samples were analyzed for dissolved and total metals, and for selected anions. All mine locations and data collected by the field geologists were entered on field forms and, subsequently, into a computer database and GIS format. With the information provided by the inventory, the Forest Service, in cooperation with other agencies, has been able to prioritize abandoned mines for reclamation. In most cases, cleanup is approached on a watershed basis. Mines in priority watersheds have been selected for reclamation first. Watersheds where studies prerequisite to cleanup are occurring include the upper Anirnas River, Willow Creek (tributary to the upper Rio Grande), Chalk Creek (tributary to the upper Arkansas River), the Uncompahgre River, and the Alamosa River. During the inventory, evidence of naturally occurring water quality degradation was found in areas where little or no evidence of mining activity exists. These areas include the upper Alamosa River, the Middle Fork of Mineral Creek, Peekaboo Gulch, and Handcart Gulch. Water from these natural sources has been found to significantly exceed Colorado water quality standards for several metals.

Jan 1, 2000

By Cathleen J. Webb, Arden D. Davis

Begun in 1992, an abandoned and inactive mine inventory in the Black Hills National Forest has resulted in a hazard ranking of the most severely affected sites. For purposes of the inventory, the Black Hills were divided into three main regions: the northern Black Hills, with primarily gold mines; the central Black Hills, with pegmatite mines and some gold mines; and the southern Black Hills, with primarily uranium mines. A computerized data base has been developed along with standard forms for field crews. The forms were designed to provide maximum compatibility with other abandoned mine inventories on various federal and state lands. Measures recommended for the most hazardous and heavily affected sites include regrading of unstable slopes, fencing of open shafts, and remediation of the most severe acidic mine drainage problems. Specific examples are illustrated where remediation and safety measures were recommended or have been implemented. The vast majority of the sites, however, needed little or no remedial action.

Jan 1, 1995

By J. D. Templeton

A petroleum well that is not in use because it has ceased to produce oil/gas economically and dry holes are referred to as abandoned wells. Once a well is abandoned it is plugged with cement and can take anywhere from two days up to a week to cure depending on the number of plugs in the well. Since plugging a well costs capital, most wells are abandoned at the lowest possible cost and with the minimum obligations set by regulation agencies. These wells can present an enduring liability to petroleum companies. However, the depth and abundance of abandoned petroleum wells makes them an economically attractive source of geothermal energy. Geothermal energy harvested from an oil/gas well is a renewable energy source as long as it is extracted in a sustainable manner. The energy can be used to generate electricity, used directly for heating, incorporated into a water desalination process, or used by a heat pump for heating/cooling applications. In this paper we examine the possibility of extracting geothermal energy from abandoned oil/gas wells by studying the heat transfer in underground geothermal heat exchangers installed in these wells. The design configurations for the geothermal heat exchangers embedded inside a petroleum borehole can be a u-tube design or a shell and tube design (i.e. double pipe). Using in-situ gathered information from some representative petroleum boreholes, the effects of key parameters such as geothermal gradient, ground temperature values, and the flow inside of the tubes are evaluated. In order to provide a constant power production the inlet temperature can be adjusted to keep the difference between outlet and inlet temperatures equivalent. Higher differences between inflow and outflow temperatures will result in a less sustainable load put on the in-situ geothermal energy. Adding insulation to certain sections of the designs can minimize the transfer of thermal energy from the fluid to the surroundings. Insulation can also limit the thermal loss between the inflow and outflow tubes in the shell and tube design. Minimizing the energy loss of these designs leads to an increase in the outlet temperature, meaning a higher grade of heat. The sustainability of long term geothermal heat extraction is a balance between the rate at which geothermal energy is extracted and the rate at which the ground formation can replace this heat. Higher outlet temperatures can lead to a larger amount of power generation, and a higher coefficient of performance for heat pump applications.

Aug 1, 2013

By G. Konstantopoulou

Environmental degradation due to abandoned quarries is an international problem, more intense when these sites are found in urban or suburban zones, in environmentally sensitive areas or are visible from sites of special interest. Rehabilitation solutions applied worldwide, range from simple relief restoration and planting to more sophisticated site exploitation in order to serve specific social needs. The elaboration of rational rehabilitation plans for every site presupposes deep knowledge and comparative evaluation of all the parameters of the problem. In this paper, a methodological approach of rehabilitation solutions for abandoned quarry sites is elaborated, based on domestic and international experience and practice. Solutions are grouped in eight main categories. In every category the framework of prerequisites and confinements (environmental, technical, social, economic, legal) for their application in Greek quarry site is investigated. A comparative assessment of alternative restoration solutions is introduced, using tools supplied by environmental economics, cost-benefit analysis, G.I.S. and multi-criteria analysis and follows in two stages: 1) Establishment of a set of criteria aiming at a priority list for a number of quarry sites located in a geographical or administrative district. 2) Assessment of alternative solutions for every single quarry from the previous priority list for the selection of the most adequate using technical, economical, social and environmental criteria.

Jan 1, 2008

By R. K. Singhal

A sizable surface mining industry exists in Western Canada. There are the surface coal mines in the provinces of Alberta, British Columbia, and Saskatchewan producing the bulk of Canadian Coal. The two oil sands plants in Fort McMurray, Alberta producing synthetic crude oil are surface mining operations. Much of the metalliferous mining in British Columbia is carried out by open pit methods. This paper discusses the current surface mining methods in both of these industries with particular reference to Alberta. Issues relating to environmental impact assessment, mine reclamation and mine site closure have been dealt with.

Jan 1, 1995

By Rafael Flores

En los últimos años, el Perú ha crecido en términos de energía generada a través de los proyectos mineros y demanda vegetativa, donde se ha verificado un fuerte crecimiento en la zona norte y sur del país. En este sentido, el presente texto desarrolla un análisis del abastecimiento de la demanda del SEIN (Sistema Eléctrico Interconectado Nacional) en su conjunto, así como en los subsistemas centro, norte y sur, a través de la evaluación del crecimiento de la demanda y los nuevos proyectos de generación, considerando principios esenciales en la estructura de un funcionamiento adecuado de los sistemas interconectados.

Sep 14, 2009

By Hernando Labarthe Correa

La presente investigación busca establecer una política racional para el abastecimiento de insumos que elimine los trámites burocráticos a través de una política de insumos de Mediana Minería que pueda generar un ahorro real de divisas y una mayor producción minera. En este sentido, se define el significado económico de los insumos, se divide la categorización en insumos nacionales e insumos importados, se revisa el reglamento del Art. 125° del decreto legislativo 18880 y los trámites de exportación, así como la importancia de las ferias internacionales y el depósito de mercancías en el perfeccionamiento de este sistema.

Nov 20, 1978

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

By Marcelo Rocco Salinas

La presencia de arsénico en aguas de mina (efluentes mineros) es una preocupación constante en el Perú, debido a que los receptores superficiales de estos efluentes son utilizados para bebida de animales, o riego de plantas. Las razones de la presencia de este metaloide están asociadas a la mineralogía propia del país. En este manuscrito se presentan los resultados de pruebas a escala industrial realizados en una compañía minera ubicada en el distrito de Canarias, provincia de Víctor Fajardo, departamento de Ayacucho.

Sep 1, 2017

By J. R. Hoffert

ON Oct. 27, 1941, the Sanitary Water Board of the Commonwealth of Pennsylvania called a meeting of the representatives of the coal operators in the Schuylkill River Basin, and frankly suggested to the operators that they "clean up their house" before someone else came in and did it for them; that they should not emulate the railroads with their "public be damned" policy and its fateful results. It had been four years since the passage of the antipollution law of 1937, a law which exempted silt from collieries until such time as a practical method existed for the removal of their water polluting properties. It had been fifteen long years since Sisler, Frazer and Ashmead concluded that 900 million tons of culm and silt had been deposited in Pennsylvania's streams in the process of preparing five and a half billion tons of anthracite for the world's consumers. Fine coal was being "mined" in the streams by "washeries" and river dredges downstream from the collieries, and silt banks no longer held back the endless black stream entering the Schuylkill at the rate of 350,000 tons per month. The coal operators were apparently working on the outmoded assumption that each ton of fine coal prepared displaced a ton of larger sized, more profitable coal. The meeting between the Sanitary Water Board and the coal operators signaled the beginning of the end of Pennsylvania's pollution problems. As a result a committee was formed at that meeting by the operators to find out what conditions were at each colliery. The Bureau assisted in the indication of methods of measurement and sampling and in the development of forms for reporting the needed data. One large producer had its chief engineer supervise the gathering of the information concerning the quantity of waste waters, the amount and sieve analyses of the waste solids, and the existing means for retaining

Jan 3, 1950

By Christian Bourcier

La méthode d?exploitation traditionnelle de la mine est le chantier chambre-magasin. Cependant, lors de l?exploitation d?un chantier, nous avons été confrontés à un problème de soutirage. Le minerai abattu est resté accroché à l?intérieur du chantier ce qui nous obligea à soutirer environ 200 wagons, représentant 700 tonnes. Suite à l?ampleur de la situation, nous avons décidé de finir l?exploitation du chantier par la méthode sous-niveau long trou retraité. Cette première expérience de récupération de piliers ayant été réalisée avec succès, nous avons décidé de continuer avec deux autres récupérations de piliers afin de pouvoir augmenter notre expertise autant au niveau technique qu?au niveau économique.

Oct 1, 2001

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By U. Richter

Conveyors are a highly effective means of transporting material over long distances. Recently there has been a trend toward long conveyor systems with high capacity single flights. These conveyor systems are an efficient alternative to costly truck fleets. Also with deeper mines, the use of diesel driven trucks becomes more difficult. Another trend is in underground mining, where conveyors are an efficient alternative to drift hoists or dedicated rail systems.

Jan 1, 2012

By H. J. Hager

The Alabama By-Products Corp. is an entirely independent Alabama enterprise. Organization of the company stemmed from the consolidation of three important properties in the Birmingham District and a by-product coke plant at Tarrant, Ala. In 1924 ABC was merged with the Pratt Consolidated Coal Co. This merger greatly extended the company's holdings of valuable coal lands in Walker and Jefferson Counties.

Jan 12, 1950

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

By Denilson de Camargo Mirim

Corte, furação e texturização são alguns dos processos que utilizam laser na produção industrial comercial. São processos bem estabelecidos, que contam com equipamentos dedicados e metodologias bem estabelecidas. Apesar de eficientes e de certa precisão, são processos térmicos com inconvenientes intrínsecos como rebarbas, material ressolidificado, zona afetada pelo calor e certa imprecisão dimensional. A utilização de pulsos laser ultracurtos, de largura temporal da ordem de algumas dezenas de femtossegundos torna possível a realização destes processos sem a produção de calor, como no caso de dielétricos, ou com geração desprezível de calor para o caso de metais. Neste trabalho, utilizou-se o aço AISI 1045 para o estudo da interação com pulsos laser de femtosegundos, com o intuito de obter as condições de processo em que a produção de calor seja minimizada ou até mesmo eliminada. Os parâmetros de processo variados foram a largura temporal dos pulsos laser, 25, 87 e 124 fs, a densidade de potência e o número de pulsos sobrepostos. A técnica D-Scan foi utilizada para a determinação dos limiares de ablação em função deste número de pulsos sobrepostos. Foram analisadas a microestrutura das regiões vizinhas à região ablacionada, com o intuito de identificar as possíveis transformações de fase que poderiam estar correlacionadas à produção de calor pelo processo. Condições de mínima produção de calor foram obtidas com minimização de produção de rebarbas e de material ressolidificado.

Aug 8, 2018