Search Documents

By R. D. Gibbs, C. C. Taylor

The gas-lift, or circulation of gas for the production of crude oil, now includes the gas operator in field production activities to a greater extent than ever before. It is the purpose of this paper to show the scope of his activities and to discuss the various means of handling and treating the large quantities of gas which are now of a somewhat different nature than formerly. The extent of the stripping action of circulating gas on oil must be discussed, as this can be governed somewhat by the method of treatment of the recirculated gas. Change in Gas-decline Curve under Circulation Before the advent of the gas-lift, the gas-production curve of a field showed a peak during the flush production with a rapid decline as the wells were put on the pump and then a long steady decline curve of a relatively small volume of rich gas for the life of the field. Under the gas-lift method of production, instead of having the sharp decline at the end of the flush production period, sufficient circulating gas to keep up the required total gas-oil ratio would be turned to the wells. The gas-production curve then assumes a long gradual decline, giving a large volume of gas for treatment for several years to come. The gas-decline curve will not follow that of the oil, as the lowering of the rock pressure by the steady production of oil and gas from the sand will make it necessary to continue using the large tubing and to circulate large volumes of gas in order to keep the back-pressure against the sands as low as possible. A Complicated Distributing System In tracing the flow of the gas from the time it leaves the well until it again enters through the casinghead, under high pressure, we get a very good idea of the complex distributing and regulating system that must be installed and the large treating and compression plants that are necessary (see Fig. I). Gas traps must be large enough to efficiently separate large quantities of gas and oil and should be elevated sufficiently to enable the oil, if

Jan 1, 1928

By R. W. Bond

The gas-lift is a comparatively recent development in the Oklahoma and Kansas fields. It was used to some extent in the old Dilworth field several years ago, but the first extensive installations were made in the Tonkawa and Garber fields in Oklahoma early in the year 1926. Compressor Equipment During the early development of the system, the equipment used generally consisted of small tandem compressors of about 250 cu. ft. per min. displacement, driven by automotive-type gas engines, using a short belt drive. These compressors were first installed at the individual wells largely as an experiment. After the experimental installations had proved the method a success, it was considered economically advisable to centralize the compressor equipment in strategically located stations. However, as the information in regard to "gas-lift flowing life" was anything but definite, and the most optimistic estimates in regard to it did not exceed six months, portability of equipment was still the first consideration in the minds of many operators, who continued to install srnall semi-portable com-pressors in their centralized stations. As electric power became available in the fields, the electric motor came rapidly into use as the prime mover for the small compressors. The operating cost of this motor is greater than that of the automotive-type gas engine for the same power output, but the greater continuity of service tends to balance the extra cost. Aside from the semi-portable units, a number of strictly portable compressors were used. These consisted of automotive-type gas engines direct connected to vertical compressors. The unit was assembled on one base and could be mounted on wheels or skids as desired. The chief objection to these, in the writer's opinion, was their small capacity— approximately 150 cu, ft. per min.—which made it necessary to use two, three, and sometimes more units per well, thus making the installation rather costly. However, they have been found valuable for test purposes and emergencies, where installation time is an important factor.

Jan 1, 1928

By L. L. Brundred

The major portion of the production of the Gulf Coast area, represented by South Texas and South Louisiana, comes from the flanks of well-defined salt domes. This oil, containing an excellent lubricating stock, ranges from 17° to 28° Be. gravity. Some lighter oil is encountered but the life of such fields is, in general, an open question. In fact, there are few light-gravity fields which have proved of much value. In all of the fields water encroachment, or, more properly, water produced with the oil, is a vital factor. After the first head of high-pressure gas is removed, ever-increasing percentages of water appear, and naturally the life of the wells is materially affected thereby. The sands are, as a rule, extremely fine, very soft, and must be carefully excluded from the hole by the use of fine screen to prevent sanding up. All sands are tipped at such extreme angles as to make coring essential for the location of water strata, oil-bearing sands and important shale. beds. Even with modern coring, the correlation of logs is a difficult problem. Due to the fact that the bulk of the oil is refined for its lubricating properties, little attention has been paid to losses by evaporation in the field. This is largely influenced by the fact that the major companies have set a price schedule, showing but two grades, "A" and "B." The average oil company, therefore, does not attempt to use the gas-lift but relies primarily on the air-lift and then only on wells considered to be particularly adapted to its use, namely those capable of producing large quantities of fluid and yet not having sufficient "kick" to flow. Furthermore, as the gas contained in the reservoirs is mostly ricthane such gas being very quickly vaporized and produced in large quantity in the early life of the fields, there is little gas left after the first flush flowing period of the wells. In fact, it is very generally conceded that gas is a precarious fuel to depend on in any of the coastal fields. This situation largely accounts for the fact that air, as the lifting medium, is almost universally used. In the average field, wells are drilled on the flanks of the domes in close proximity to one another, largely on account of the extreme dips of the formation and "town lot" leases, and space to set up machinery and

Jan 1, 1928

By C. R. Swarts

The use of compressed air or gas in oil wells for raising crude oil to the surface has, within the last year, become a dominant factor In production engineering. Previous application of this principle was largely confined to oil wells that had been pumping for a considerable length of time. In the Seminole area, the gas-air lift has been applied to wells imniediately after natural flow has ceased and in some cases while the wells were still flowing. This early application of the gas-air lift has been watchcd with intense interest by the petroleum industry, both with respect to methods of application and mechanical installations and to the effects on immediate and ultimate production. Methods of Application The Seminole pool at its inception contained sufficient gas associated with the oil to cause natural flow. As no frce gas was found in the main productive horizon, the Wilcox sand, all the gas present was dissolved in the oil, hence the natural flowing life was short, rarely lasting over 45 days. When natural flow ceased, high fluid levels were common, and as depth and crookedness of holes were obstacles to efficient pumping, the gas-air lift was used almost exclusively in raising the oil to the surface. Because of the high gravity of the oil, 41" A. P. I., and its high gasoline content, and also because of the desire to obtain production before offset wells became productive, quantity of production was the aim of the operators and a method of flow was used whereby this aim could be fulfilled. One of the outstanding features of this method consisted in flowing the wells through the annular space between the tubing and rasing. By this means a greater quantity of fluid could be handled than by flowing through the tubing of the size in ordinary use. Wells that would produce only a few hundred barrels on the pump were by this rnethod made to produce as high as 7000 bbl. on the lift. A few days or wreks of production at that rate meant a large recovery of oil. Casing of 636 in. diameter was commonly used as a production string with a 5 3/16-in. liner set on top of the oil sand. Upset tubing for irtro-

Jan 1, 1928

By H. C. Miller

The gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air-lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas-lift possible, or where natural gas is plentiful and inexpensive. We find, therefore, in California, that natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanies the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the tubing and flow lines. The gas-lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible, to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecrans field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas-lift at approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1928

By E. V. Foran

TheRe are many factors which control the ultimate production of oil and gas from a producing formation and the rate at which this production is obtained from any of the producing wells in the formation. The most important of these, and the one over which the greatest control can be exercised, is the differential pressure existing between the formation and the well bore. In producing any well by means of the gas-lift, it may be possible to change the flow tubing in a number of ways or vary the volume of circulating gas or air used for flowing the well, but if these operations, regardless of their magnitude, do not change the differential pressure between the producing sand and the well bore, they will in no way change the production of the well. If this statement is accepted as a fact, then all gas-lift or air-lift installations should be designed with but one object in view; namely, a means by which we can economically control very wide ranges of differential pressures between the formation and the well bore. Factors of Production In gas-lift production from any given formation, there are four major factors which govern the magnitude of the differential: (I) the depth of the well; (2) type and size of flow tubing; (3) volume of the circulating air or gas, and (4) physical properties of the oil-gas mixture after it has reached the well. The first of these factors is uncontrollable and does not vary. The other three are controllable within certain limits. The degree to which the last three factors can be controlled will cntircly govern the length of life of the well while on the lift, the lifting cost, and the daily production. It will also govern to some extent the ultimate production from the wells or leases producing by this method. These four factors will be discussed in detail in another part of this paper. Before proceeding further, a review of the present general practice in Texas, elsewhere than in the Gulf Coast region, will be given.

Jan 1, 1928

By C. V. Millikan

New developments in air-gas lift practices in the Mid-Continent area since our Pall meeting in Fort Worth have done much to increase the efficiency of installations, and thus bring within economic limit of air-gas lift many wells which could not have been flowed profitably before. After the gas-lift had so thoroughly demonstrated its value in the Seminole field, its use spread to other areas and many installations were made of which the economy could be questioned. In the Seminole area, when production began to decline it was necessary either to increase the efficiency of the air or gas-lift or to put the wells on the pump, and pumping was not a process of lifting oil to which any operator looked forward with confidence. These conditions have resulted in the development of many practices which increase the efficiency and permit wells to be flowed with air or gas which earlier could not have been flowed economically, and wells which have been flowing to continue to a lower rate of production. The practices which have come into more common usage in the Mid-Continent area recently are mostly revivals of and improvements on practices which have been known in air-lift work for several years. Many arc peculiar to the individual well on which they are used. Intermittent Flowing Some interesting results are being obtained in Seminole and other districts by intermittent injection of gas. Gas is introduced during per-iods iods of 3 to 5 min. at a rate considerably over that necessary to acquire the production at a steady rate of injection, and is then cut off for a period of 3 to 15 min. Two to five wells are run from the same group of conlpressors. The total volume of gas required is sometimes reduced as much as one-third of that required when it is introduced at a constant rate, without changing the amount of oil production. The maximum pressure required is usually higher, but the average equal to or lower than that required for constant rate of flow. The effect on the wells is usually an irregular rate of flowing which may cause inconvenience where recycling is practiced. It would seem that this increase in efficiency is due to less slippage when the gas is introduced intermittently than when it is intro-

Jan 1, 1928

By J. O. Lewis, H. R. Pierce

Since the sudden revival of the air or gas-lift and its extensive use in the oil fields, many questions have arisen as to principles and as to their application under the conditions actually encountered in the field. Much has been written regarding both theory and practice, especially on the air-lift as applied to lifting water. Many statements have been made as to the use and benefits of the gas-lift, some of which are reasonable but many of which are unreasonable, many specialty makers claiming to have devices which operate in almost miraculous ways and even to generate energy nature never possessed. These claims are often based upon incomplete or inaccurate data. A review of the literature discloses many valuable articles, but it also discloses the need for setting out more clearly the different practical ends sought, and for working out specific engineering principles upon which to formulate the design and operation of gas-lifts to meet the desired ends within the limitations of field conditions. A check on some of the published information has revealed basic errors in the sources of data upon which conclusions have been predicated and has led the writers to doubt the value of a large part of the compiled data. The writers have concluded, therefore, that it will be opportune to direct discussion to the sources of error in the data now being collected, to recommend for consideration by the engineers some methods of collecting and correlating data, and to point out some of the factors relating to the application of the air-lift principle to oil production as dictated by the different economic ends sought, and the limitations of working conditions that may be met. Until these several considerations are clearly understood by the engineers, and the unreliable data have been sifted out and dependable data substituted, there seems little chance of evolving satisfactory engineering control for the air-lift. In the following pages no distinction will be made between gas-lift and air-lift, as they are generically the same.

Jan 1, 1928

By A. H. Bell

The general principles of the gas-lift will not be described in this paper. Only specific details that have not been fully discussed in previous papers, or results that do not fully coincide with conditions previously described, will be dealt with. The principal points to be emphasized and for which supporting data are furnished are as follows: 1. Gas-lift installations usually have comparatively high efficiencies as compared with standard pumping equipment, when reduced to a basis of barrels produced per horsepower installed. 2. Advantages of high-pressure plants from the standpoint of operating efficiency and for the application of the gas-lift early in the life of flowing wells. 3. Evidence of increased ultimate yield through conservation of gas by the gas-lift. 4. Possibility of development of new equipment to increase efficiency of the gas-lift. 5. Indications of the advantages of repressuring as a means of stabilizing gas-lift wells and as a means of increasing ultimate yields. TyPes of Installation The gas-lift installations of the more important companies in California have been of the central-plant type wherever field conditions would permit. This has resulted in greater flexibility and lower installation costs per well than could be obtained with individual well units. In general discussions of the gas-lift method of production, the installation costs are frequently referred to as being too high for economical operation. If the field conditions are carefully analyzed and the plant designed with the idea of obtaining high operating efficiencies, the installation cost per well can be lowered sufficiently to compare favorably with individual well-pumping units, when the operating advantages are considered. Much greater production per horsepower can be obtained with the gas-lift than is possible with pumping equipment. Table 1 shows the unit sizes and costs of gas-lift installations of three companies in the Los Angeles basin. The cost of walking beams, rods,

Jan 1, 1928

By Cyril S., Smith

THE phenomenon of air-hardening is well known in connection with special steels. It occurs when the rate of decomposition of austenite to marten- site is so retarded that it takes place on free cooling in air rather than on more rapid cooling in a quenching bath. If an air-hardening steel is quenched sufficiently rapidly it will remain in the soft austenitic state, while if it is cooled very slowly it will again become soft owing to growth of the carbide particles. It depends on a critical adjustment of the decomposition velocity and diffusion rate, and such alloys are rather rare, especially in the non-ferrous field. In carrying out some experiments on some copper- rich copper-cobalt alloys, the author found that these possess very marked air-hardening properties. The alloys are covered by a patent issued to M. G. Corson (1,723,022-1919), which states that an alloy containing between 2 and 5 per cent cobalt is hardened by simple quenching from above 850° C.

Jan 1, 1930

By Philip D. Lindahl

The US Bureau of Mines (USBM) began research to improve the safety and efficiency of transporting coal from underground coal mines using a balanced air-lift hydrohoist (ALH). ALH includes a U-tube pipeline that can be installed through an existing shaft or two surface-drilled holes connecting the mine level to the surface. Bench- and pilot-scale models were tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a riser pipe by injecting compressed air microbubbles. A prototype injector was developed that continuously compacted -50-mm (2-in.), run-of-mine coal in a screw feeder and injected a thick coal slurry into ALH. Initial production rates of 40 t/h (44 stph) through a 200-mm-(8-in.-) diam riser pipeline were achieved with a50-m- (165-ft-) high pilot-scale model. The potential productivity was expected to increase to 100 t/h (110 stph) through modification of the coal injector.

Jan 1, 1995

By James W. Lower

IN developing the orebody on lower levels of the Star mine at Burke, Idaho, Hecla Mining Co. is faced with a serious problem in driving raises. Levels are at 200-ft intervals. As a raise is being driven between levels, at points about 70 and 130 ft from the sill, heavy pressure arches develop and the raise becomes extremely hazardous. Eventually, following a blast, caving occurs, making it impossible to recover the raise. In February 1957 it was decided to attempt sinking a small winze on the vein from the 5500 to the 5700 level. This shaft (winze-raise No. 2) was to be used as a raise prior to stoping. It was assumed, and correctly, that the heavy ground pressure could be controlled by timbering close to the bottom after each advance.

Jan 7, 1958

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005

By Fan Shaogang

In this paper, the airbags' structure and technical characteristics and its applications in China are described. Based on the practice of the airbags in mining thin seams, the effects on ground control are discussed. This paper also analyzes the interaction mechanism between the airbag and surrounding rocks.

Jan 1, 1997

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By L. A. Schutz

Personnel of the Bureau of Mines have conducted investigations in the principal asbestos mines and mills in the United States, to determine the concentration of airborne asbestos fibers in the workplace, and to establish the exposure of workers to such fibers. 'The surveys were conducted using the sampling and evaluation method recommended by the National Institute for Occupational Safety and Health. The method consists of collecting the air-borne sample on filters and, after appropriate sample preparation, counting the fibers utilizing phase contrast microscopy. The results of the investigation show that fiber concentrations are low in the asbestos mines but high in the asbestos mills, ranging well above 5 fibers/ml of air based on a count of fibers greater than 5 urn in length.

Jan 1, 1973

By J H. J Holtzhausen

Never has there been more focus on the health, safety, and well-being of our employees at the workplace. Ever evolving expectations of individuals, companies and clients are shaping regulatory reviews and advancing standards across the world in the drive to zero harm. The technology is advancing at a rapid pace, which is now allowing continuous real-time monitoring of contaminants to take place in the harshest of environments.

Oct 12, 2022