Search Documents

By C. Sensogut

The phenomenon of spontaneous combustion is one of the major hazards encountered in underground coal mines both from the safety aspects and on economic grounds. Every occurrence, however small, if not tackled effectively in the early stages can develop into open fire, or explosion of gas or coal dust. In terms of economy, even dealing with small incidents may be costly in terms of labour and materials, and in case of a sealing off of a district being necessitated, the loss of face equipment and sterilization of reserves is potentially great. Therefore, expense and effort in prevention and detection of such heating, together with a high state of readiness for dealing with likely event, is completely justified and may be considered as a sound investment. In order to achieve this investment, it may be worth to pinpoint the centre of the fire occurring due to autogenously heating which is supposed to be great assistance to inert it at a least cost and time. Therefore, it is the aim of this work to model the spontaneous combustion in the goaf.

Jan 1, 2002

By Orville Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually increases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal.

Jan 5, 1951

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By Gemuts I, Hudson D. R

Massive sulphide mineralisation at the Miriam prospect, near Coolgardie, Western Australia, is fracture-controlled and associated with disseminated sulphides near the basal contact of an ultramafic lens. The lens is peridotitic in composition with a pyroxenitic zone at its base, and lies within a sequence of altered high-Mg basalts and pillowed tholeiitic basalts. Recrystallisation of the ultramafic rock has resulted in the development of secondary olivine. The average composition of the sulphide fraction of massive ore is Cu = 4.4%, Co = 0.3%, Ni = 23.0%, Fe = 31.8%, S = 40.6%, consisting of the supergene assemblage violarite-pyrite to a depth of 210 m.

Jan 1, 1973

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By G. B. Carpenter

The United Nations Law of the Sea (LOS) Convention includes provisions (Article 76) for establishing the outer limits of a coastal State's continental shelf and for denoting the seaward extent of sovereign rights over natural resources. Determination of a coastal State's continental margin, according to Article 76, must consider eight factors: 1. The territorial sea baseline 2. The 2,500-meter isobath 3. The foot of the continental slope 4. A line 200 nautical miles seaward of the territorial sea baseline 5. A line seaward of the foot of the continental slope connecting the points where sediment thickness divided by distance to the foot of the slope equals .01 6. A line 60 nautical miles seaward of the foot of the continental slope 7. A line 100 nautical miles seaward of the 2,500-meter isobath 8. A line 350 nautical miles seaward of the territorial sea baseline Figure 1 shows the preliminary limits for each of the Article 76-based definitions for a portion of the U.S. Atlantic continental shelf. The additional areas gained beyond the 200- nautical mile Exclusive Economic Zone (EEZ) are highlighted. The first three factors are baselines from which the distance provisions of Article 76 are measured. Factors 4-8 are distance- from-baseline provisions for establishing the continental shelf limits. Factor 5, also known as the Depth of Sediment Limit or "Irish Formula", was calculated using sediment thickness data from seismic linesand isopach maps. All other factors were determined from digital hydrographic data. The Depth of Sediment Limit is the most advantageous method for the area shown in Figure 1. It is especially useful for introverted coastlines such as the Georgia Embayment and New York Bight areas. The 200-mile line is advantageous for protruding coasts such as those off major capes, e.g., Cape Hatteras. The 2,500-meter isobath plus 100-mile line gains

Jan 1, 1995

By Zhang P, Wang T, Duan X, Sheng T, Kong L, Wang Y

This paper puts forward an artificial neural network (ANN) for the forecast of deformation of the surrounding rock deformation. On the basis of this, this paper gives some examples of its application. The results show that the ANN model has a high forecast accuracy.

Jan 1, 1995

By J. B. Macelwane

GEOPHYSICS differs from geology and physics in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, volcanology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratory system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist-the exploration geophysicist -calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist-the paleontologistneeds some knowledge of geology. DEVELOPMENT OF A GEOPHYSICIST Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydrologist, or an exploration geophysicist? We may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1941

Wollongong* is Australia's largest single centre of mining and metallurgy. Wollongong's total employment in manufacturing of basic metal products (over 26,500 in 1972/1973) was almost 50 per cent higher than that of Newcastle and double that of any other Australian city. Although the great bulk of this employment was in steelmaking, Wollongong's copper industry was also a significant employer. Wollongong's total employment in mining (4,900 in 1971) was second only to that of Newcastle among Australian mining centres. Although the bulk of Wollongong's mining is of coal, there is also considerable mining of blue metal, sand and clay. In all, over 40 per cent of Wollongong's work force is employed in mining and metallurgy. The great bulk of the other

Jan 1, 1976

By P. S. Piper

In the 1960s it was suggested that the volume of stope convergence, and hence the rockburst hazard, could be reduced by the emplacement of backfill. Recent advances have facilitated the placement of large quantities of backfill underground, and a reassessment of its potential benefits as part of a regional support strategy is now timely. In this paper the principal criteria of effectiveness of backfill are taken to be its impact on face energy release rate (ERR) and average pillar stress (APS) levels, and maximization of acceptable ore extraction ratios. The possible effects of backfill on excess shear stresses (thought to modulate large seismic events) are also briefly reviewed. Analytic solutions describing backfill properties and their impact on ERR and APS in certain idealized geometries are also presented, and compared with the results of an extensive suite of computer simulations, in which parameter sensitivities are explored. Results indicate that a regional support strategy is required at depths exceeding 2 km in order to maintain acceptable levels of ERR, and backfill ribs can on their own fulfil this role at depths less than 3,3 km. At greater depths use of stabilizing pillars becomes imperative, but here too supplementary backfill ribs can reduce ERR and APS levels and permit significant increases in ore extraction ratios.

Jan 1, 1988

By H Bao, M Nehring, M Kizil, P Knights

The mining sector, a notably energy-intensive industry worldwide, is a major consumer of fossil fuels, leading to significant carbon emissions globally. The move towards electrification, coupled with advancements in battery technology, has redirected focus from traditional diesel-powered solutions to battery-powered alternatives. This paper introduces a novel mining haulage system, termed the Battery Trolley system, and examines its theoretical foundations, configurations, and operational processes. It offers a comprehensive analysis of the system’s characteristics and limitations. Through a hypothetical road simulation, the study analyses various battery mining trucks, calculating energy consumption based on force parameters and tailoring battery sizes to contemporary materials and technology. When assessing various battery truck alternatives—considering aspects such as battery size, effective payload, duty cycle, energy efficiency, productivity, and single-shift production—a range of performance outcomes and characters become apparent within the mining context. The findings indicate that Battery Trolley configurations, requiring smaller battery capacities, entail lesser compromises on effective payload. Consequently, these configurations achieve a higher duty cycle, reduced energy consumption per tonne, heightened productivity, and enhanced singleshift production capabilities compared to Battery-only alternatives. The comparative analysis of Battery Trolley with stationary charging (BT-S) and Battery Trolley – dynamic charging (BT-D) underlines that battery Trolley systems are capable of overcoming the challenges associated with battery size, thus successfully fulfilling the production demands of large truck applications in mining. This positions Battery Trolley systems as a more advantageous option for the decarbonisation of mining fleets, underscoring their potential in contributing to the sector’s sustainable evolution.

Sep 1, 2024

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By E. R. Spencer, E. Reeves

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By R. V. Ramani, K. V. K. Prasad

"Solution of most engineering problems requires, in addition to vast ·numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity; However; it is only .recently that approaches like the expert systems methodology have been developed to ·incorporate the Judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or ""shells"" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development or a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.INRODUCTIONExpert systems (ES) are interactive computer programs which use high quality specialized knowledge in some narrow problem domain to solve complex problems in that domain. These complex problems lack structured and/or standard ways of solution and involve substantial use of subjective and experience based knowledge. One of the first expert systems was MYCIN, developed in 1974, in which subjective and heuristic knowledge of expert physicians was used to diagnose infectious diseases and provide antimicrobial therapy (Buchanan arid Shortliffe, 1984). Since MYCIN, expert systems applications have appeared in other areas such as mineral prospecting (Gaschnig, 1982), configuration of computers (McDermott, 1982) and structural engineering (Bennett and Englemore, 1979)."

Jan 1, 1989

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989

By G E. Ho, M Anda, S Dallas

Water auditing and water conservation measures are fast becoming the quantitative tools for water balance reporting in the mining and minerals processing sector. Therefore, this paper was written to describe the process of water auditing in a goldmining environment and to contribute towards building an appropriate water management framework for The Cooperative Research Centre (CRC) for sustainable resource processing (CSRP). The research will assist with the assessment of water balances in mining and hydrometallurgical processes and ongoing probabilistic modelling for Newmont Mining Corporation, its wholly owned gold mines, and its joint venture operation of Kalgoorlie Consolidated Gold Mines (KCGM). Kalgold or KCGM are the managers of a joint venture project between Barrick Australia (50 per cent) and Newmont Mining Corporation (50 per cent) at Kalgoorlie, Western Australia (WA). Boddington Gold Mine (BGM), Western Australia, will commence operations this year and manage the new goldmine expansion project. BGM is 100 per cent Newmont owned and will operate to continue mining gold and copper from the existing (BGM) site that was decommissioned in 2001.

Jan 1, 2009

By James C. Cawley

A summary is presented of existing leaky feeder communications systems currently in operation in North America. Background information pertaining to previous use of leaky feeder technology is discussed along with the survey methodology. A review of some pertinent facts concerning propagation in tunnels and specific reference to mine tunnel propagation is presented. A summary of the characteristics of each mine visited is presented in tabular form, and methods of procurement and maintenance are discussed. The role of user training in efficient system use is presented. Seven sites representing eight mines are included in the survey. Economic and technical topics are considered.

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today's machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972