Search Documents

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By O. Knacke, H. Barth, W. Gans

The rate of cementation was determined by measuring the time required to consume a thin electrodeposited layer of the cementating metal as indicated by a sudden increase in the electrical potential. The diffusion controlled cathodic current of the more positive metal was measured by conventional electrochemical techniques and compared with the cementation rate under the same experimental conditions. Micrographs revealed different types of crystal growth in different surroundings e.g. dendritic growth in acidic solutions.

Jan 1, 1973

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d'emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

From March to May of 1963, the Bureau of Mineral Resources carried out an experimental aeromagnetic survey at Cobar, New South Wales, to field test a proton-precession magnetometer installation in the Cessna aircraft VH-GEO. The Cobar area was chosen as considerable information was already held on the Earth's magnetic field there, which was known to provide a range of anomalous areas that are not excessively disturbed.A procedure for survey flying and methods for processing data were developed during the survey. Contour maps of the aeromagnetic results were produced in the field. The experimental survey was successful in outlining magnetic anomalies in detail.INTRODUCTIONSince 1951 the Bureau of Mineral Resources, Geology and Geophysics (B.M.R.) has carried out an airborne magnetometer exploration programme with DC.3 aircraft carrying fluxgate magnetometer equipment. Recently a proton-precession magnetometer was developed by the Design and Development Group of the B.M.R. for observatory use. One unit modified for airborne use was installed in the Cessna light aircraft, VH-GEO. The Cessna was modified structurally to take the magnetometer, associated bird, and winch gear.The proton-precession magnetometer has many good features.1. It utilises the transistor and associated solid-state devices in its electronics, and hence is light and small.This is the basic feature allowing its installation in a light aircraft. The transistor circuits have a high reliability factor and owing to the card sub-unit...

Jan 1, 1964

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

By Susanna A. C. Stadler, Chris Aldrich, Jacques J. Eksteen

Slag foaming occurs in several pyrometallurgical processes. These processes include steelmaking in basic oxygen steelmaking furnaces and electric arc furnaces as well as various non-ferrous operations like sulphide smelting/converting and base metal slag cleaning. Although slag foaming in steelmaking processes has been extensively researched, little attention has been given to slag foaming in non-ferrous operations. Slag foaming phenomena are complex because often the system consists of three or more phases. With this in mind, factors previously identified as influencing slag foaming were investigated. These include the slag basicity, physical properties of the slag, namely viscosity, surface tension and density, the formation of particles due to undercooling of the slag and the FexO concentration in the slag. The effect of increasing FexO concentration was found to decrease the foam index due to lower viscosities, but higher surface tension depression appears to have led to increased foam index values at high FexO concentrations. The foaming index decreases with increasing basicity, until precipitation of solids occurs. After this point, the foaming index was found to increase with increasing basicity due to increased solids precipitation. In general, increasing amounts of slag-wettable solids led to higher foam indices, but the precise nature of the effect on slag foaming was dependant on the nature of the solid precipitate.

Jan 1, 2003

By Terry G. Richard, Sunder H. Advani

A sequence of 250 unconfined compression tests were completed on a common marine shale indicative of the overburden strata of east- central Ohio. The samples were of a light gray clay shale of Pennsylvanian age. The shales considered are obvious layered materials with distinct bedding planes. For this reason there is sufficient evidence to consider this material as anisotropic in nature. With a properly chosen reference coordinate system this anisotropy can be reduced to a layered orthotropic characterization. This implies that the mechanical properties can be specified with regard to principal material directions. With this nature in mind a systematic study of the combined influences of strain rate and moisture conditioning was initiated. Of particular interest is the variations in unconfined ultimate compressive strength with variations in the controlled parameters of strain rate, moisture conditioning level and direction of testing. Results of this particular phase of the program are presented.

Jan 1, 1982

By Werner Goldsmith, Akihiko Kumano

An experimental investigation was conducted to study the response of soft, porous rock, green shale, under dry and liquid-filled conditions to normal impact of hemispherically-tipped cylindrical steel projectiles with diameter and mass of 6.35 mm and 31 g, respectively. Disk-shaped green shale specimens with nominal thickness and diameter of 32 mm and 127 mm, respectively, were tested in the initial projectile velocity range of 18 to 42 m/s. For the liquid-filled tests, the green shale specimens were saturated with kerosene. A total of eight impact tests were conducted. Information on the extent and pattern of the damage in the rock and velocity histories of the projectiles were collected. It was found that while the penetration depth was quadratically related to the initial projectile kinetic energy for the dry case, the penetration depth for the liquid-filled case was directly proportional to the initial projectile kinetic energy. The results of the impact tests under dry and liquid-filled conditions conformed well to a linearly viscous model and a Coulomb frictional model, respectively. The major deformation processes in the dry specimens were found to be compaction and equivolumnial distortion of the material. In the liquid-filled case, however, formation of cracks and equivolumnial distortion with less material compaction were observed. Furthermore, craters were formed as a result of the crack formation in the liquid-filled specimens.

Jan 1, 1982

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By McPherson M. J

An experimental investigation was carried out to determine the various gas flow characteristics of bituminous coal samples. Adsorption and desorption tests were first conducted to estimate the quantity of methane that is retained by coal, and the rate at which it is released. Experiments were then carried out to study the variation in coal permeability with changes in applied stress and gas pressure - factors that change continuously with time. To further understand the phenomena involved in retention, release, and flow of gas, electron microscopy was used to study the microstructure of coal and how it affects these characteristics of coal.

Jan 1, 1988

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By Morandini AF, Occella E, Clerici C, Mancini R

This contribution presents the first results of an experimental research aimed at finding an unified description of the first stages of a rock comminution process. With reference to the case of the jaw crushers and to the specific subject of the comminution law, the tests reviewed and analysed in this contribution have been carried out, at a laboratory scale, on five different materials (limestones, quartzite, serpentinite) at different reduction ratios and feed rates, and accurately recording both total power and idle running power. The analysis of the results has shown that: ò the grain size distribution of the products complies with a modified form of the Rosin-Rammler equation, already found to be well suited to representing the grain size distribution of blasted rock in previous works by the authors; ò observed trends of the consumed power at increasing reduction ratios is steeper than predicted by the classical Rittinger, Kick and Bond laws, Rittinger law representing however a closer approximation of the experimental results; and ò a more accurate description of the experimental results is provided by a modified form of the Rittinger law. Accuracy of the semi-empirical expression has been found to be usually better than ten per cent by comparing actual results with expected Results.

Jan 1, 1993

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By N. P. Reddy

This paper describes an experimental setup for multiple-fan ventilation systems at the ventilation laboratory of the WVU Department of Mining Engineering. Housed in a 30 ft by 70 ft room, the experimental setup consists of three 18 in. variable-speed axial-flow fans, the 18 in. diameter fiberglass tubing and fittings for arranging networks, and the pitot tube measuring and data acquisition system. The fiberglass tubing and fans can be organized into the non-planner network of two fans or three-fans. It is mainly designed for studying the characteristic curves, operating points, and fan stall for the multiple-fan ventilation system.

Jan 1, 1992

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994