Search Documents

By David Meadows, Elmer Palmer, Steve Dixon

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large “state of the art” concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By Postupack C

A major problem that has continued to plague the surface and underground coal industries is blast induced damage to the coal seam. Blasting Analysis International, in conjunction with a number of other organizations, has continued to address this concern through 14 years of field research in 68 full-scale production environments worldwide. Compiled results were obtained from varying field conditions. These included single and multiple seam coal mines, horizontal, rolling and steeply dipping coal seams and varied borehole diameters (ranging from 102 to 381 mm) and when using various explosive formulations. Results are discussed in detail along with the tools, test methods and analysis techniques to identify and quantify the problems. Over ten major causes of coal damage were identified. A number of practical and economic recommendations are presented that can benefit the entire coal and blasting industry especially in commercial operations whose economic growth relies heavily upon recovering an undamaged coal seam.

Jan 1, 1995

By D S. Stewart, K W. Keskimaki

The Henderson Mine has been utilising a continuous panel caving method to extract molybdenum ore since starting operation in 1976. In the past three decades since the mine was designed, many changes have taken place in underground technology as well as the general nature of the mining business. The impacts of larger scale underground equipment and automation are significant at Henderson and continue to reshape the nature of the enterprise. During the first years of operation in the 1970s, Henderson required almost 2000 employees to achieve full production, today only about 400 people are required to fully utilise the plantÆs capacity. The most recent change to the facility is the conversion from a rail haulage system to an underground crushing and conveying system that transports ore 25 km to the Henderson mill site. This change has required the introduction of large, rubber tired haulage trucks underground and the mining methods necessary to develop the large openings demanded by the trucks and underground crusher. The development of the underground crusher is also the first step to mining the final bottom horizon of the orebody. Along with this move comes an opportunity to almost triple the effectiveness of the mining effort, through higher draw columns and wider draw bell spacing. This final advancement to a totally trackless mine has positioned Henderson well for safe and efficient operation as it enters the 21st century.

Jan 1, 2000

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively consistent over the past five years, longwall production levels have increased significantly during this period. Longwall production currently accounts for approximately 50% of U.S. underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face ventilation system and advancement of face ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch of the National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory has examined several basic principles of the longwall face ventilation system, and has evaluated the effectiveness of numerous improved face ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face ventilation parameters on longwall mining sections and investigating the fundamental relationship between face air flow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels from using belt entry air to ventilate the longwall. Novel methods have been identified to increase the amount of face air flow and to manage face air flow to most effectively minimize face workers' dust exposure. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results, throughout the longwall mining industry, as documented from surveys conducted in the early 1980's and 1990's, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1998

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By S. A. Jeric

In-pit crushing and conveying of waste has been utilized in the mining industry for over 30 years. In recent years, innovations in crushing, conveying, and particularly waste and leach stacking technology have sparked a renewed interest in continuous haulage systems for large-scale open pit applications. A review of the advantages/disadvantages and operating techniques of crushers, feeders, conveyors, and stacking systems currently available is made. The paper examines some operations that are currently using large scale continuous haulage systems. Finally, a case study is presented that evaluates the application of a continuous waste haulage system in a large open pit mine in the Western United States, The case study includes a economic comparison with the existing truck haulage system.

Jan 1, 1997

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization's structure that addresses the immediate and long-term impact of a company's products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By V. K. Handa

Sterlite Industries (I) Ltd. started its copper smelter in 1996 and worked through the common problems associated with smelter start-ups. Specific issues in the converter area included converter blower IGV problems, punching machine reliability, converter spitting, back collar burning, ,and short converter campaign life. With a very young and dedicated team of engineers and technicians, smelter management assigned teams of three to four members to work scientifically and systematically through each major problem area to recommend and implement appropriate solutions. The converter mouth was redesigned with respect to tuyere and metal height to eliminate spitting and back collar burning. The air line was changed in places to reduce the pressure drop. A new back-up compressed air line and vessel was installed to prevent tuyere blockage in the event of a blower trip or power failure. The converter mouth liners and bricking around the mouth was modified to eliminate metal leaking through the pouring lip Modifications to the punching machines were made to address specific problems and preventative maintenance practices were further streamlined and reinforced to ensure 100% availability of hot metal cranes, converter blowers, punching machines, and ID fans. Matte availability and matte temperatures were improved by streamlining the upstream ISA and Rotary Holding furnace areas. Implementation of a detailed training program for the converter operators significantly improved the operation and morale. Water-cooled double hoods and a third converter were installed as part of the smelter modernization plan. The new hoods dramatically improved hygiene in the crane aisle while the addition of the third converter posed new challenges for the same motivated group of crews with respect to flip flop operation to keep the idle converter hot and to maximize in-stack time, managing crane/ladle logistics, and managing revert generation. This paper describes the converter operation's journey from the initial days of long blowing times and large revert accumulations to present operations with two converter flip flop operation, and also describes the team work, constant focus on increasing productivity and reducing costs, and benchmarking.

Jan 1, 2002

By J. Yue

"Mount Milligan mine is located in northern British Columbia. The concentrator employs conventional SABC grinding circuit with bulk sulphide flotation processes. Commissioning started in September of 2013 and nameplate production of 60,000 TPD was reached in the fourth quarter of 2015. As is typical with many mill ramp ups, bottlenecks developed as throughput increased. Since then, plant modifications and new control philosophies in the comminution and flotation circuits have been implemented and evaluated. The mine-to-mill collaboration played a key role in reaching target throughput rates by improving blast fragmentation and implementing temporary pre-crushing. Results of the projects as well as ongoing challenges/bottlenecks and solutions will be discussed.IntroductionMount Milligan Mine is a copper-gold producer located approximately 253 km northwest of Prince George in British Columbia. Production commenced in September 2013 and reached nameplate capacity of 60,000 TPD in December 2015. Average head grades for the mine life average 0.18% Cu and 0.39 g/t Au.Circuit DesignOriginal process design began with run-of-mine ore from the pit crushed through a 60-110 gyratory crusher, conveyed to a live ore stockpile and fed to the mill via four variable apron feeders. The concentrator circuit employs SAG mill - Ball mill - Pebble Crusher (SABC) grinding configuration to grind the ore down to a target P80 of ~200µm. It is then fed to two parallel trains of flotation tanks, each consisting of five 200 m3 tank cells with the first two being roughers and last three being scavengers. Concentrate streams from roughers and scavengers are separately reground with a closed circuit Tower mill and two open circuit ISA mills operating in parallel, respectively.Three stages of cleaners upgrade roughers/scavenger products to 25% Cu followed by a cleaner scavenger stage. The final concentrate is then thickened and filtered to approximately 9% moisture and shipped off site (Figure 1)."

Jan 1, 2017

By J. Warner, K. A. Hughes, P. E. R. Blanchard, J. Esslifie-Dughan, J. W. Reid

Tailings management plays an important role in reducing the environmental impact of Orano Canada’s uranium mining operations in Northern Saskatchewan. Uranium ores mined from Northern Saskatchewan are often associated with large amounts (10-20 wt%) of other harmful elements, such as arsenic and nickel. The JEB Tailings Management Facility (TMF) located at McClean Lake, Saskatchewan is designed to prevent potentially harmful water-soluble elements, particularly arsenic, from contaminating the surrounding environment by promoting the formation of water-insoluble minerals. It is therefore important to determine which arsenic-containing mineral species are present in the TMF and how they evolve over time. Researchers at the Canadian Light Source (Saskatoon, Saskatchewan) were successful in identifying the arsenic mineral species present in tailings samples collected from the TMF in 2013 using X-ray absorption near-edge structure (XANES) spectroscopy. XANES analysis verified that the majority of arsenic species in the TMF existed as amorphous and crystalline ferric arsenates with minor amounts of arsenite and arsenide species. Herein, XANES is again used to analyze a new set of tailings samples collected from the TMF in 2018, specifically focusing on the difference in the distribution of arsenic species in old and new tailings.

Jan 1, 2020

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

The Geological Resource Map of New Zealand (GERM) is a computerised inventory of aggregate, mineral, coal, petroleum and thermal water occurrences, containing summary information on location, production, geology, and geochemistry. The types of occurrences include quarries, mines, gold dredges, wells, outcrops, seeps, springs, and fields. The file contains entries for about 10,300 sites and is used to produce tables of data and maps at any scale, for single or multiple commodities. The published format is the New Zealand 'Geological Survey map series Geological Resource Map of New Zealand 1:250 000'. Seventeen of the 27 map sheets covering New Zealand were published by August 1991, with three more close to publication.

Jan 1, 1991

By P. A. Geusebroek, N. A. Duke

Abstract - The Lupin mine, located in the central Slave province just east of the western boundary of Nunavut Territory, is a world-class example of a Neoarchean-aged banded iron formation (BIF)-hosted lode-gold deposit. At the minesite the gold-mineralized Lupin BIF, separating stratigraphically underlying psammitic wacke and overlying argillaceous turbidite sequences, delineates the Lupin dome, a hammerhead-shaped F2/F3 interference fold structure occurring at the greenschist to amphibolite facies metamorphic transition within the thermal aureole of the Contwoyto batholith. Detailed paragenetic relationships indicate that peak thermal metamorphism coincided with the switch from regional D2 compression to rapid D3 unroofing of the Neoarchean orogenic infrastructure. Gold initially precipitated with pyrrhotite, replacing amphibolitic BIF at the apex of the Lupin deformation zone, separating the east and west lobes of the Contwoyto batholith. Over the course of associated prograde/retrograde metasomatic overprints, gold was further remobilized during garnet and loellingite/arsenopyrite growth in chlorite-altered selvages of late-forming ladder quartz veins. A metamorphic model of ore genesis, with gold being scavenged and transported by metamorphic fluid that was shed and structurally trapped at the amphibolite recrystallization front, is favored over the previously proposed syngenetic and exogenic models of gold concentration that have tended to polarize genetic interpretations to date.

Jan 1, 2004

"Outotec’s TankCell® e500 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland. The TankCell® e500 is the first cell in this size class (500m3) to be run in an operational duty and it has been working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50. In addition the cell has proved to be very energy efficient, operating with a specific energy of around 0.4kW/m3 under production conditions. This presentation will provide a review of the installation and operation of the TankCell® e500 at Kevitsa and will summarize the results found in the published literature from the various testing campaigns conducted around the cell. INTRODUCTION The TankCell e500 was installed and commissioned at the Kevitsa mine in northern Finland in 2014. Post startup the cell was initially run for testing and optimization with various test campaigns undertaken. but was subsequently taken into a production duty (Mattson et al., 2015a). At Kevitsa the cell is run as the first copper rougher replacing the previous two copper roughers (both 160m3) in this duty. The unit is running at between 38-40% solids at a feed rate of approximately 850tph. Since operational the average copper recovery from this single cell has been around 71% copper. This is typically with an enrichment ratio of around 50 being fed with an average head grade of 0.3% copper. More details on the circuit configuration and production performance of the e500 at Kevitsa can be found in Mattson et al., (2015a) and Murphy et al., (2016). In addition through the optimization program with the use of a variable speed drive controlling rotor speed it was found the the e500 was very energy efficient under production conditions. During this work the cell was found to run at a specific energy of around 0.4kW/m3 which exceeded design expectations (Xia et al., 2015)."

Jan 1, 2016

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By E. A. Metz

It has been approximately four years since IARC reclassified crystalline silica as a “Group One” substance. Since that time, crystalline silica has been considered a human carcinogen. Silicosis is a preventable disease and several aggressive campaigns have been developed to increase awareness of silica dust related problems in the industrial environment. New analytical techniques are being developed to determine quantitatively the amount of crystalline silica in materials. Yet, still much is to be learned about the surface properties of silica and the way in which the disease progresses into full-blown silicosis. This paper will discuss the interaction of free radicals generated by the mineral particles and lung tissue. It is the cell injury and DNA damage that progresses to fibrogenesis. Freshly fractured surfaces of silica contain free radicals. These free radicals play an important role in the stimulation of the alveolar macrophage and the development of the inflammatory reactions leading to the fibrotic response caused by silica. Engineers, scientists, and physicians need to discuss the mineralogy of silica and the technical issues concerning the development of silicosis.

Jan 1, 2000

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By A. G. Doll

"This paper expands the SAG mill survey database published by the Author at Procemin 2013. The new database includes 49 published SAG/AG mill surveys and includes mills from all over the world. The paper will compare the survey database to SAG mill models by Austin, Morrell and Hogg & Fuerstenau with the purpose of demonstrating the degree of fit of the models to surveys and validating any empirical “fitting factors” used in the models.SAG mill power draw models are used in mill design and grinding circuit modelling to predict how much power will be consumed by a particular mill geometry and operating configuration. The importance of conducting surveys suited to model calibration will be highlighted because the review of literature shows that survey information important to modelling is often missing or omitted. A recommendation for the collection of data during a mill survey is presented, along with some assumptions used by the Author in the absence of certain data. The benefit to mining companies of publishing their survey data, and thereby allowing modellers to improve their model calibration, is discussed.The comparison of models requires a discussion of the measurement of power in a mill drive system as the models use slightly different position in the electrical network for ""where power is measured"". The benchmarking of models against plant operations requires a similar discussion of power measurement."

Jan 1, 2016