Search Documents

By R. E. Old

THROUGH the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-balance methods and the equations for natural water encroachment to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed.

Jan 1, 1942

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By Christopher Mark

Preventing pillar line squeezes, massive pillar collapses, and coal pillar bumps is critical to the safe and efficient recovery of coal during retreat mining operations. To help prevent these problems, the U.S. Bureau of Mines has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to, and the load-bearing capacities of, pillars during retreat mining operations. The program can accommodate various retreat mining scenarios including angled crosscuts, varied entry spacings, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder entry designs as well as active workings. A data base of 130 pillar retreat case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1.5.

Jan 1, 1995

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By Yuting Xue, Khaled Mohamed

Rib control is a critical component of underground coal mining operations, and comprehensive rib support design is essential for ensuring the safety of miners. However, there is currently no standardized approach for rib support design in the United States. To tackle this issue, the National Institute for Occupational Safety and Health (NIOSH) has developed a standalone application, Design of Rib Support (DORS), for rib stability assessment and rib support design under development load. The rib support design in DORS starts with the rib support density, which is determined from the unsupported rib factor of safety (RibFOS). The relationship between rib support density and unsupported RibFOS was obtained from the collected field data. The objective of this research is to validate DORS rib support design by analyzing the extent to which the proposed design capability was utilized to support the coal ribs using numerical simulations. A series of numerical models with varying overburden depth and rib height were built and the ribs were supported with the DORS-recommended rib support design. The bolt load was analyzed under different conditions and the results show that bolt load varies with the overburden depth, the location of the bolt and bolt length. The load in the bolt(s) increases with the reduction in unsupported RibFOS. The bolt(s) start to yield when the unsupported RibFOS falls below a threshold value of 0.8 and secondary support is necessary.

Jun 25, 2024

By T. Alan O'Hara

"The decision to invest capital in developing a mine and constructing a mineral processing plant and services is usually made after a feasibility study shows 'that the estimated future cash flow from mine operations will yield an adequate return on the estimated capital expenditures.The actual return on investment may differ substantially from that estimated in the feasibility study, because of the probabilities of errors in estimating capital costs, ore reserves, operating costs, mineral revenue and operating productivity. This paper outlines the R.S.S. (root sum of squares) risk analysis procedure of computing the overall probability of the actual project D.C.F. (rate of discounted cash flow), differing from that estimated in the feasibility study.Variation in Project D.C.F.It is assumed that a feasibility study of the project has been completed which has defined the estimated values for all the project parameters, such as ore reserve tons and grade, capital cost, concentrate recovery, metal revenue, daily milling capacity and operating costs.The financial analysis of the mining project will have determined that the cumulative cash flow will yield an expected D.C.F. on the capital cost if all project parameters attain the estimated values. If, however, the actual value of any parameter varies from that estimated, the actual project D.C.F. will vary from the estimated D.C.F. Risk analysis methods attempt to determine the overall effect of probable variations in the estimated values of all project parameters on the D.C.F. of the mining project. This overall effect is expressed as a probability profile, which shows the likelihood of actual D.C.F. values greater or less than that estimated.Thus, a completed risk analysis of a mine project, with an expected D.C.F. of 15.51%, would display the characteristics shown in the preceding diagram."

Jan 1, 1982

By Z. Hladysz

It is common to nine a coal seam affected by previous extraction of a coal seam below. As a result of that severe problems may occur during the extraction process. This paper presents the analysis of undermining effects based on field observations. A simplified method for the evaluation of risk in undermining operations is presented and predictions of the degree of possible damages to the undermined coal seam is given.

Jan 1, 1985

By C. Richard Tinsley

INTRODUCTION The economic analysis (Chapter 3), the engineering studies (Chapter 10), the credit structure (and the consequential funding sources) - Chapter 11, and the overall feasibility structure for any venture are all directed to determining one major decision element: How much and how certain is the reward for taking these risks? Risk assessment is a surprisingly weak area of analysis and is usually addressed in a checklist fashion. It is much preferable to deal within a risk system so that the inevitable tradeoffs among risks are correctly made. DEFINITION The first step toward risk definition must be to ascertain all of the risks to which a project or a company is exposed; otherwise one will remain ignorant of the possibility of a financially crippling loss until it occurs. (Carter and Crockford, 1974). However, simply stating what "risk" is can lead to debate. For example, risk could be (adapted from Vaughan, 1982): -the chance of a loss - uncertainty of loss -possibility of loss - uncertainty -dispersion of actual from expected results - probability of an outcome different from the one expected - possibility of an occurrence of an undesirable contingency -a condition in which a possibility of a loss exists. For the minerals industry financier, the last definition is probably the most appropriate. However, from a mineral company's point of view the definition might well include the possibility of not achieving the expected financial return. RISK CLASSIFICATION Risk identification will be readily agreed as the all-important first step. There are five major "branches" of risk classification. These are: -Statistical -Modellers -Checklist -Project Financing -Insurance The Statistical set discovered probability theory and any risk discussion soon deteriorates into a mathematical jungle (Megill, 1977; Hartman, 1976; Reutlinger, 1970; and Pouliquen, 1970).Their use of terminology tells its own story: coin toss (binomial distribution), gamblers' ruin, delphi (oracle) techniques, monte-carlo simulations, random walks, etcetera. These techniques inadequately represent the judgements necessary in an increasingly complicated and interrelated world. The risk Modellers have turned to the computer to handle these inter-relationships but soon find barriers because of "simultaneity". Certainly the computer has its uses to conduct various analyses (marketed as "sensitivity" analyses) but very often one finds that this involves changing one or two variables at a time, all other things being equal. Unfortunately, in a modern and complex world all other things do not remain equal. The statisticians will, no doubt, jump to their own defence by citing this

Jan 1, 1985

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By Charles J. Haas

The resistance which rock bolts offer to shear movements along fracture planes and bedding planes near a mine opening has been suggested as one of the mechanisms by which bolts contribute to the support of weak rock in the roof or sidewall. That such displacements do occur is a fact fairly well known. Inspections of drill holes that have been drilled for some time often reveal that the holes have been offset at one or more points some time after drilling. Resin grouted bolts are often cited as being better able to resist shear movement in the roof because the annulus around the steel bar is filled with grout, whereas the sides of a conventional bolt will not contact the rock until a rather large shear displacement has occurred. When this project began, there were no experimental data to support or refute the above arguments. A laboratory shear test program was, therefore, devised to evaluate the effectiveness of various types of bolts in resisting shear under various conditions which exist in situ. Research reported earlier (Haas, 1976) included a theoretical analysis of a conventional bolt intersecting a shear surface, and experimental data on the shear resistance of smooth (lapped) shear surfaces, intersected at various angles by conventional and resin grouted bolts. The present paper extends the previous analysis to consider the effect of the initial roughness of the shear surface. Joint roughness is a particularly significant factor since undulations of the shear surface cause dilatation of the joint, which in turn, causes high tensile loading of a bolt intersecting the joint.

Jan 1, 1982

By S. L. Crouch

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Alejandro Ferrada Vergara, Héctor Espinoza Muñoz

Drilling and blasting stages are considered factors that impact downstream processes significantly and over all the mining business value chain. Adequate control of these processes may represent energy savings in comminution processes. There has historically been a resistance to design change as this implies more drilling and implementation costs due to new technologies in explosives, which added value is difficult to quantify.

Jan 1, 2016

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

By Daniel H. White

Block caving, unlike most other conventional forms of mining relies principally on the natural forces within the rock mass to fragment and transport the ore. Obviously, not every orebody can be satisfactorily mined by block caving. In the early stages of mine planning an attempt should be made to assess the benefits of the block caving system relative to others, and develop a reasonable mining concept that may be used to provide preliminary information to mine planners and financial specialists. It is the intention of this paper to outline some basic geotechnical parameters that are essential to: 1) Assessing the feasibility of block caving an orebody and 2) Providing semidetailed information relative to mine design based on drill hole and other data.

Jan 1, 1979

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

By T. Prof. Egleston

How to interpret the composition of rocks has been a question which has caused a great deal of discussion and investigation among geologists and chemists. It is evident that that analysis will give the clearest results, which will give the relative proportion of the different minerals composing the rock as well as the weight of their different constituents. This, however, is a very difficult matter, and in those rocks which seem to the naked eye entirely compact, like obsidian and other rocks of that class, appears to be impossible. Cordier, in the early part of the century, invented a process which is known as the " mechanical analysis of rocks," which is really a method of mechanical preparation, and consists in crushing the rock to a certain fineness, and then, by virtue of their density, washing out the different minerals, so as to make a mineralogical analysis, separating completely the different constituents of the rocks. In the hands of so skilful a man, this was a comparatively easy matter, and Cordier found no difficulty in ascertaining the mineralogical composition of a rock. The ultimate chemical composition was ascertained from the sum of the elements contained in the different materials. In the light of to-day, it is very easy to see that the complete chemical analysis of the rock does not necessarily lead to the explanation of its character. It has been so difficult, however, to have any other kind of analysis made that most chemical examinations have been made as ultimate, and not as mineralogical analyses. The panning out of the different minerals composing the rock, which are often very nearly of the same specific gravity, is so difficult that a person of ordinary mechanical skill is scarcely able to do it; consequently the mechanical analysis which Cordier proposed, and was able himself so skilfully to effect, has never been practiced to any extent. A school was formed in France consisting of a very small number of Cordier's followers, which, in face of the difficulty of acquiring the method, very soon died out as a school, though some of his most skilful followers are still living. The next important step in ascertaining their composition was to out the rock into transparent sections and examine the minerals with

Jan 1, 1875

By Tim Miller, Michael M. Murphy, John L. Ellenberger, Gabriel S. Esterhuizen

"A limestone mine in Ohio has had instability problems that have led to massive roof falls extending to the surface. This study focuses on the role that weak, moisture-sensitive floor has in the instability issues. Previous NIOSH research related to this subject did not include analysis for weak floor or weak bands and recommended that when such issues arise they should be investigated further using a more advanced analysis. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to demonstrate the effect that a weak floor has on roof and pillar stability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface.IntroductionMassive roof falls extending to the surface at a limestone mine in Ohio have been studied collaboratively by the National Institute for Occupational Safety and Health (NIOSH) and the mine owners. This paper provides a summary of the sequence of events leading to observed instability and presents a numerical modeling analysis that investigates the role a weak floor can have on roof and pillar stability.This study builds upon previous NIOSH research in underground limestone mines undertaken by way of a survey that analyzed performance of pillars in 34 different stone mines in the Eastern and Midwestern United States between 2005 and 2009 (Esterhuizen et al., 2011). This survey led to the development of underground stone mine pillar design guidelines based upon a “stability factor” for the pillar system. The factor is compared to operational experience to determine ranges of values that are typical of stable pillar systems. A software package titled Stone Mine Pillar Design (S-Pillar) was developed for easy application of these guidelines (Esterhuizen and Murphy, 2011).Weak floor in the present case study departs significantly from cases included in the previous NIOSH research, in that none of the 34 study mines had weak floor issues. Moreover, this case study is the first in which a weak floor has been monitored routinely as roof falls are occurring. A detailed report on the observations and measurements taken at the mine has been published (Murphy et al., 2015). The previous observations led to the conclusion that although there were weak bands in the pillar, the weak floor was the significant defect that led to the instability issues. The pillars were initially mined in 2004, approximately 10 years before the instability issues began to occur. The objective of this study is to use numerical models to analyze a variety of floor strengths and the impact of moisture content to find the critical point at which the floor becomes unstable, leading to long-term instability issues."

Jan 1, 2015