Search Documents

By Albert Adu-Acheampong

Fairmount Mineral's Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

By Woodcock JT

This paper reviews the chemistry of flotation pulps with the aim of gaining a better understanding of the effect of chemical environment in flotation and ap- plying the knowledge to improving the con- trol of reagent additions. Theories of flotation are considered briefly, but they are only of limited help in specifying an appropriate chemical environment and in establishing control techniques. The chemical nature of flotation pulps is reviewed. Four distinct phases are present - solids, an aqueous liquor con- taining many dissolved reactive sub- stances, organic liquids, and gases. All of these vary in many ways and interact with each other. It has now been estab- lished that there are many previously- unsuspected materials present in plant pulps that can or might affect flotation. Concentration profiles of selected para- meters in operating plants are given to show some typical changes that occur. Recent advances in collector chemistry, especially that of xanthate and related species, are reviewed. Modes of decompo- sition and/or formation in pulps of xan- thate, dixanthogen, perxanthate, xanthyl thiosulphate, and monothiocarbonate are reviewed, and their W absorption spectra are compared. Some relevant information on dithiophosphates, mercaptobenzothia- zole, and thionocarbamate is summarized, and some speculative comments are made about reactions of these collectors.

Jan 1, 1984

By J. W. Fuller

DURING the last 20 years, experimenters have sought to utilize pulverized coal in boiler plants, but refractory and slag troubles have usually overbalanced any, gains in efficiency that were obtained. These troubles were caused largely by lack of knowledge of the proper methods of coal preparation and lack of a furnace design that would be adaptable to pulverized-coal firing. When this information was obtained the results were so much more satisfactory that within the last 5 years approximately, 80,000 boiler hp. have been installed in plants ranging from 1000 to 20,000 boiler hp. rated capacity, which are operating at an average of 174 per cent. of rating. The first commercial installation for burning pulverized coal under boilers was made at the Parsons shops of the M. K. & T. railroad in 1916. Of eight 250-hp. water-tube boilers thus fitted, six were operated continuously for 3 yr., when oil was obtained at such a low price as to warrant its use. Since then, this plant has been operating alternately on pulverized coal and oil, depending on prevailing prices. Recently gas has been discovered within 20 mi. of this plant, so that this fuel may also be used. No change in furnace design was made when changing from pulverized coal to oil or gas firing. One of the principal advantages of this method of firing is its ability to utilize, with maximum efficiency, all kinds of coal, irrespective of quality or physical characteristics. In fact, quite a number of the present pulverized-coal installations were made for the purpose of utilizing coal that could not be marketed or used in any other way. The Pacific, Coast Coal Co., at Black Diamond, Wash., formerly hand fired the boilers, using approximately 125 tons of prepared steam-size coal daily. The Black Diamond steam coal is the best quality of coal for steaming purposes mined in that section of the country, and there is a market for all that can be produced. By installing a pulverizing plant, it was possible to substitute coal of a size and quality that had no commercial value, so that 125 tons daily of the best steam coal formerly used at the mines is now marketed.

Jan 12, 1921

By E. W. Steele

IN THE copper-casting department of a modern electrolytic copper refinery there are two kinds of casting furnaces: the first, or anode furnace for casting crude copper into anodes for electrolysis; the second, or refined-copper furnace for casting the cathodes resulting from electrolysis into market shapes, such as ingots, wire bars, and cakes. Both furnaces are reverberatories of practically the same general design and are operated intermittently, putting through a charge normally in 24 hours. The treatment of the copper in both furnaces is similar, in so far that oxidation followed by skimming and reduction (poling) is carried on in both; but in the refined-copper furnace, the work must be done with greater care and it is of extreme importance that not the slightest trace of impurity be introduced into the copper. The furnaces usually hold from 150 to 300 tons of molten copper, which constitutes the daily charge. Except in the case of furnaces in the Lake district, where the concentrates from native-copper ores are charged through the roof, the furnaces are charged through the side doors by charging machines similar to those used in open-hearth steel practice. In 1916, at the Perth Amboy plant, of the American Smelting & Refining Co., located at Maurer, N. J., a study was made of the possibility of firing the copper refinery furnaces with pulverized coal instead of by hand. The proposed method possessed obvious advantages over hand firing and coal was a much cheaper fuel than oil at that time. It was realized, however, that there were several objections to its use, the principal ones being the liability of increasing the sulfur content of the refined copper, and the additional slag that might be produced from the ash. The increase of the sulfur content of the refined copper was the more serious, as more than 0.002 per cent. sulfur is objectionable. In the case of the slag, any increase would be expensive as the copper in this slag would have to pass again through the entire smelting and refining process.

Jan 3, 1925

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By John Goheen

RECENTLY the head burner at a brick. plant with over 40 years' experience said that he had burned brick by guess for over half his lifetime and had used pyrometers for 2 1/2 years but hoped that he would never have to burn kilns without pyrometers again. The ceramic engineer in making a special study of the burning of clay ware and the effect the heat of the kiln has on color and vitrification is also rapidly placing the burning of clay on a twentieth-century basis. Clay ware may be divided into various groups, brick and drain tile; sewer pipe; firebrick; and pottery, which, in turn may be subdivided into special classes. As nearly as the analysis of the clay type of kiln, etc., will allow, there are practically the same problems to solve in burning in all of the processes or operations. The underlying objective is the same, namely the production of the best grade of ware under the most efficient and economical manufacturing system. The principal problem in the production of clay ware is the burning off of the kilns. The most modern steam shovel may dig the clay and the most advanced types of pug mills and wire cut machines or molds of various kinds may be installed, but unless the drying and burning of the ware is successful, all of the previous operations will be useless. On this final operation depends the entire result of the plant. In reality, burning of all. clay ware is purely a heating proposition. The kilns, or furnaces, should be so designed as to give equal distribution of heat. Consequently, the problems of design and construction of kilns to produce equal distribution of heat require serious consideration, as do also the questions of heat control and draft control. The three most important factors in the burning of practically all types of kilns may be

Jan 9, 1919

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By C. B. Thwing

IT is likely that among most races, owing to the ease of finding and working clay, the making of clay utensils was learned earlier than the molding of metal implements. The ancients made good pottery and durable brick in kilns that wasted fully one-half the heat and spoiled fully one-fourth of the ware; and, taking the clayworking industry as a whole, we are doing the same today. The chemical and physical changes involved in the burning of clay are so many and vary so much with the composition of the clay that it is not surprising that the rule-of-thumb methods so commonly employed fail to give uniform results. In its passage from plastic clay to the vitreous or stonelike character the mingled minerals and accidental organic impurities of which the clay is blended must pass through four stages, the second and third usually overlapping, and the fourth often beginning before the third is complete. These stages in their order with the rising temperature are drying, dehydration, oxidation, vitrification. In the first part of the drying stage, usually accomplished in part outside the kiln, the water mixed with clay is dried out at temperatures not much exceeding the boiling point of water. In the later part of this stage, within the kiln, the hygroscopic water, absorbed from the air is expelled at somewhat higher temperatures, this stage being known as watersmoking. Some clays are very sensitive to temperature during the drying stage and if the temperature exceeds 100°, the ware becomes checked. Other clays may be dried more rapidly without danger. In down-draft kilns, the draft is slight during the watersmoking stage and the water driven off from the top rows condenses on the ware in the bottom of the kiln, with the result that high temperatures are likely to be reached at the top of the kiln before the bottom is fully dry. The lag in temperature of the bottom persists to the second stage in spite of the better draft then prevailing.

Jan 9, 1919

By Kirtland Marsh

THE manufacture of gas masks by the Chemical Warfare Service, U. S. A., required preparation of the carbon used in the canisters. The largest plant for the production of this carbon was situated at the works of the Astoria Light, Heat and Power Co., at Astoria, N. Y.; this paper will deal1 with the pyrometry equipment at that plant. Commercial charcoal was found unsuitable for use in gas masks because of its low power of absorption and its poor resistance to abrasion. The best raw material for the production of carbon was found to be coconut shells, but any kind of nut shells or fruit pits were used when sufficient quantities of coconut shells could not be obtained. The shells were first carbonized in retorts, the carbon was then crushed and screened between 8 and 16 mesh, and finally submitted to a special heat-treatment in air; steam treatment was later substituted for treatment in air. The production of gas-mask carbon on a commercial scale was begun at Astoria about Aug. 1, 1917. Temperature control was essential during the initial carbonization of the shells, as well as during the air or steam treatment, and pyrometers were installed for this purpose. The installation and maintenance of all pyrometry equipment was done by the pyrometry department, consisting of an officer in charge, an assistant, and two men. A special pyrometry laboratory was maintained in which all repairs were made.

Jan 9, 1919

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By John W. Ahlrichs

Microscope, electron microprobe and x-ray diffraction have been used to provide quantitative evaluation of products from the mill, smelter, refinery and other metallurgical processes. Phase compositions and their quantities are necessary for an adequate understanding of the various products obtained throughout an operation and in laboratory testing. By careful evaluation, important information can be gained in improving recoveries and increasing grades at various stages of processing. Four case histories are discussed in this paper. Quantitative microscopic counting techniques are applied to mill products to determine degrees of locking and liberation of the economic minerals. Rapid, but accurate evaluation aids the metallurgist to develop or improve the grinding and flotation circuits. In the smelter, the identification and quantification of the phases are important for predicting reaction mechanisms and kinetic trends. Mineralogic techniques have been applied to conventional smelter products, and to those obtained in laboratory tests for newly developed innovations to smelting. Small, but important, values of gold occurrences in ore are difficult to determine. Evaluation of gold usually requires special separations into various mineral concentrates, followed by assays and mineralogic determinations of the products. Numerous occurrences of solid solution constituents can be treated as by-products, but often they are deleterious to metallurgical treatment. Most solid solution problems can be unraveled by the mineralogist's tools.

Jan 1, 1981

By Yuanming Pan, Brett Rogers, Baoquan Hu, Gary Yeo, Christine Austman

The nature and distribution of radiation-induced defects (RIDs) in quartz from the Maw Zone, a yttrium- and rare-earth-element-enriched sandstone breccia complex exhibiting intense hydrothermal alteration, have been investigated by electron paramagnetic resonance (EPR) spectroscopy. EPR spectra show that detrital quartz in sandstone, from five diamond drill holes intersecting the Maw Zone and one above the crest of the so-called Quartzite Ridge, contain only background-level RIDs, indicating that Ubearing fluids were absent in this area. However, close to the sandstone-basement unconformity, in hole WR-194 immediately west of the Quartzite Ridge, the concentration of RIDs in detrital quartz is significantly above background but at least an order of magnitude lower than those at the Key Lake and McArthur River deposits. Widespread drusy quartz at the Maw Zone, which signifies intense hydrothermal alteration, is associated with hematite-, sulfide- and carbonate-bearing mineral assemblages, which exhibit complex crosscutting relationships. EPR spectra of drusy quartz in all three types of mineral assemblages are low in RIDs as well, supporting the EPR evidence that fluids at the Maw Zone did not carry significant U. These EPR results suggest that, in spite of intense hydrothermal alteration and favorable structural geology, the Maw Zone is unlikely to host any significant U mineralization. Moreover, this study shows that the EPR technique is potentially a useful exploration tool, capable of determining whether individual alteration zones in the Athabasca Basin were associated with U-bearing fluids or not.

Jan 1, 2013

By Robert G. Ditchburn, Cornel E. J. de Ronde, Bernard J. Barry

The age of mineralization, its mode of formation, the time elapsed to amass an economic deposit, its capacity for sustainable extraction and, ultimately, its grade and tonnage, are key aspects in the economic viability of volcanic massive sulphide (VMS) deposits (Ditchburn et al, 2004). Radiometric dating methods applied at GNS Science have been recently refined with the purpose of efficiently determining the ages of seafloor VMS mineralization along active intraoceanic arcs. These developments include: determining the longevity of seafloor hydrothermal systems, details of individual chimney and massive sulfide mound growth, and insights into deep-seated processes, such as the transfer of elements from magmas to their overlying hydrothermal systems. In our pursuit to better understand seafloor hydrothermal systems along intraoceanic arcs, we have thus far compiled age information for three volcanic centres of the Kermadec arc (South Pacific) and one of the Mariana arc (NW Pacific).

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By Gifford White

CONSIDERABLE attention has been directed in recent years to methods of electric prospecting other than the conventional direct-current tech-niques. It has been extensively recognized that electrical data of a more general nature than that possible by direct-current methods might be useful in geophysical studies. To this end, a number of different types of electric currents have been employed, such as single-frequency alter-nating currents, square-topped periodic current waves,4 periodic surges of a less specific nature,8 and suddenly applied direct current.1,2 Yet, to the author's knowledge, little analysis of these different types of driving currents has been made from the standpoint of network theory to determine just what type of currents would give the most useful data, and, most important of all, to determine the relation of the data taken by one method to those of another. Without touching on the actual theoretical problem of how currents flow in the earth under specified boundary conditions, some very useful information can be obtained from the study of the fundamental integral equations of electrical networks, throwing light on the problem not ordinarily appreciated by the field worker. Some manipulation of the standard network equations will be made, with the sole purpose in mind of developing expressions leading to practical results. Suppose that four points in the earth have been located and it is wished to obtain the most useful type of electrical data by inserting current into two of them and measuring the potential developed between the other two. The first problem that arises is that of which pair of the four shall be chosen as current grounds. In the direct-current case, where only steady potentials are measured, the selection is of little consequence, but as soon as currents varying with time are used at the current grounds, a new effect arises. The fact that a varying current is flowing in the current-carrying conductor between the current grounds means that magnetic and electric fields varying with time will be produced

Jan 1, 1940

By L. Lafrenière

A trend in mining exploration is to increase the number of geophysical parameters collected and interpreted for geological features in a given area. Airborne technology now allows us to simultaneously combine electromagnetic, gravity, aeromagnetic and radiometric surveys. We report the results of a multiparameter survey conducted in the area of Kamiskotia, Ontario. This area is located near and on the West side of the multi-metalliferous Kidd Creek deposit. Various metallic occurrences are reported in the studied area. Integrating multiple parameters in the interpretation produces a more detailed pseudogeological map than what has already been published. 3D interpretation has been undertaken using some of these parameters and suggests that future work is required in 3D earth model solutions in order to fully use all parameters.

Aug 1, 2013

By C. F. Gleeson

"Geochemical stream-sediment reconnaissance can be a useful exploration tool from the point of view of rapidly and cheaply evaluating the mineral potential of an area. This is particularly true of rugged and mountainous areas such as are found in Gaspé. For the past two years, SOQUEM has been carrying out such surveys over favorable geological regions in the Appalachians of northern New Brunswick and Gaspe. To date, about 4,000 square miles of terrain has been systematically covered by reconnaissance geochemistry. Jeeps have been used as a means of transportation in the easily accessible areas and a helicopter equipped with a winch has been used to lower crews into the more difficult-to-reach regions. Such surveys have been successful in finding metallic mineralization which otherwise might not have been detected.Electronic computation of analytical information has been used to construct regional metal maps, rolling mean maps and residual metal maps. These maps have helped in evaluating anomalies, in relating the regional geo-chemistry to the regional geology and in comparing the distribution patterns of metals. To date, some 30,000 stream-sediment samples have been collected from the Gaspe region and analyzed for Cu, Pb, Zn and Mn. These analyses are being subjected to computer analysis."

Jan 1, 1969

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009