Search Documents

By E Villaescusa

This paper summarises research work carried out at the Western Australian School of Mines on mine backfill properties in the last few years. The fill properties presented relate to cemented aggregate fill and cemented tailings fill. Emphasis of these studies has been placed on the composition of backfill materials including aggregate particle size distribution, cement dosage and influence of cement admixtures. The unique features of the backfill research carried out at WASM during the last few years are the accomplishment of a study into the properties of large cemented rockfill samples by triaxial testing and the investigation of the properties of fill material made from highly saline ground water prevailing in the Goldfields region of Western Australia. Exploring different cost-effective binding agents for mine backfill was also carried out at WASM. Special effort has been put on the development of fill materials compatible with hydraulic and paste fills. During the process, specific methods and procedures for laboratory testing of backfill material have been formalised. The on-going backfill research on sample scaling is summarised and the future direction of WASMÆs backfill research focus is outlined.

Jan 1, 2000

By Angus M. Henderson, Charles R. Lilley

Underground mining at Kanowna Belle commenced in July 1998, using a sublevel open stoping method. The use of this stoping method necessitated the use of a cemented fill material for filling primary and secondary stope voids. A detailed engineering study recommended the construction of a cemented aggregate fill (CAF) system for Block A, in favour of paste fill. The CAF system consisted of a crushing and screening plant, a surface binder preparation plant and an underground fill station. Conventional underground dump trucks were used for CAF delivery. Since CAF plant commissioning in March 1999, 1.2 million tonnes of CAF have been placed underground. CAF segregation was the most significant quality control issue during CAF system operation. At the hangingwalls of filled stopes, CAF segregation sometimes occurred to such the extent that the resulting fill material was essentially uncemented coarse aggregate. This caused some CAF dilution during the extraction of adjacent secondary stopes. Numerous CAF were prepared on site for strength testing. A relationship has been formulated that allows estimation of the CAF uniaxial compressive strength in MPa, based on the cement content (c) and porosity (n), as follows. [ ] Practice at Kanowna Belle has confirmed that laboratory testing results cannot be applied for optimising the mix design of cemented rock fills that do not exhibit debris flow behaviour during placement. The grain flow characteristics and consequent marked segregation dominate the in situ fill strength. A detailed review of backfill requirements for the lower mine indicated that the total net present cost of CAF and paste systems was similar. Several significant operational advantages offered by a paste system have resulted in its selection for the remaining mine life. The construction of a paste fill system at Kanowna Belle is currently in progress.

Jan 1, 2001

By H. A. D. Kirsten

The assessment of backfill as a support medium in gold mines has been based generally on its ability to reduce the amount of potential energy available to cause damaging rockbursts. While this regional support effect is very important, the methods of analysis commonly used to quantify it predict that, owing to the very compressible nature of the fill, the support provided in areas of small convergence will be negligible. This prediction, however, is contrary to the conditions observed in practice, namely that weak fill does provide a discernible beneficial effect. In addition to the regional support effect, several mechanisms of secondary support, particularly those applicable to areas of low convergence, are identified and discussed. These include the mechanism of deformation of the detached hangingwall beam, rotational and shear effects on bedding, joints and fractures, joint infill, the continuous support effect of the backfill under static and dynamic conditions, the preservation of the integrity of the hangingwall beam, and the potential modification of local stress fields. Confidence in the validity of some of these mechanisms is afforded by the results of theoretical investigations into the behaviour of backfill- supported stopes. The results dealt with are: ? the behaviour of the hangingwall as a beam on an elastic foundation; ? the behaviour of stope/backfill, modelling the surrounding rock as a jointed rock mass.

Jan 1, 1988

By L Neindorf

The development and application of paste fill, cement slurry aggregate fill and shotcrete bulkheads at Mount Isa Mines is described. The progressive changes in filling style in the Mount Isa copper mines from a dry fill based cemented rock fill to tailings based paste fill and slurry fills is explained. The development of shotcrete arched bulkheads and engineered drainage system is described. Details on how Mount Isa Mines has achieved approximately 30 per cent cost reduction in backfill operations through innovations are given. The development of a rocky paste fill is explained.

Jan 1, 2005

By A G. Grice

Surface disposal of mining processing wastes is usually perceived as an undesirable consequence of meeting societyÆs needs for metals and minerals. Environmental disasters associated with the discharge or storage of such wastes, though infrequent, can have very damaging consequences for the environment and the industry. Reducing or eliminating the potential for such events may be achieved by placing some or all of these processing wastes back into the voids created by the mining operations. Processing operations may limit or enhance the opportunities for using tailings and other waste products as a backfill material. Backfilling is a truly multi-disciplinary process and requires the informed involvement of mining, metallurgical, engineering and environmental specialists. This paper describes the range of fill types currently being used in Australian mines, particularly those utilising processing wastes as constituents. It focuses on how processing operations can affect the suitability of these materials for the various types of fill, the resulting fill properties, fill performance and costs.

Jan 1, 2002

By D Morrison

Backfill is usually considered a necessary evil that contributes little to the principal objective of the operation, ore production. Consequently, it is relegated to an auxiliary role in the operation with minimal equipment and resource allocation in planning and is only superficially considered during feasibility studies. In many mines, the inadequacy of the design and operation of the backfill system ultimately leads to frequent delays, excessive costs and, in the worst cases, major instabilities which result in reduced ore production and lost or unrecoverable ore reserves. The primary objective of backfill is to prevent the progressive deterioration of mined out excavations. With the exception of narrow vein operations, it is too weak to alter the mining induced stress regime and control stress concentrations caused by stope extractions. However, the direct benefits of backfill include the possibility to consider a wider range of mining methods, recovery of 100 per cent of the planned resource and the selection of a stoping sequence that minimises the regional stability problems that cause production shortfalls in the later years of mine production. Indirectly, backfill is a practical means of solving other issues, such as waste disposal, that impact the viability of mining. In Australia, the geotechnical conditions of many mines are becoming more difficult and increased attention to the importance of backfill is warranted. This paper describes realistic aspects of backfilling and the positive impacts a well co-ordinated fill system can have on mining activities as a whole. Examples are presented where an integrated approach to backfill systems have offered significant benefits to the operation.

Jan 1, 1998

By C Linklater, J Chapman, A Watson

Closure options under consideration at some sites include backfilling mined-out pits with waste rock. Backfill may include mineralised and non-mineralised waste rock. Following groundwater rebound, flow-through conditions may develop in the pit post-closure. The backfill located in the saturated zone below the water table may release solutes under such conditions. It is therefore important to understand the potential impacts that backfilled pits could have on postclosure groundwater quality.Geochemical characterisation programs are the foundation for assessing the potential chemistry of water that has contacted mined wastes. Such programs must be designed to obtain data relevant to the closure options under consideration. To complement standard testing techniques, SRK utilises saturated column testing designed to generate data on leaching rates under anoxic conditions that could be encountered within submerged backfill.This paper presents the findings of saturated column test work carried out on waste rock samples from an iron ore mine in the Pilbara.CITATION:Watson, A, Linklater, C and Chapman, J, 2016. Backfilled pits – laboratory-scale tests for assessing impacts on groundwater quality, in Proceedings Life-of-Mine 2016 Conference , pp 110–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

By W Schauenburg

The increasing problems associated with the disposal of waste and the potential for use of by-products as underground filling material is a subject which is relevant not only to the coal-mining industry. The progressive scarcity of surface disposal facilities for by-products and waste has now become a problem in all sectors - not only for the mining industry. The considerable capacity offered by underground cavities which exists in various mining branches present an extremely promising potential in this context. The backfill process for coal mining developed by DMT in co-operation with Ruhrkohle AG make use of the cavities which are offered by the extraction of coal. It consists of several stages: The fine-grained by-products, such as sludge, filter cakes, fine refuse, ash and flue-gas cleaning residues are processed on the basis of specified formulations in metering, blending and pump facilities on the surface to produce pumpable pastes with precisely defined flow characteristics. On Walsum Colliery of Ruhrkohle AG up to 200 m3/h stowing paste is conveyed into the mine in pipes with diameter of 200 mm (8"). The delivery pressure of the pump operating on surface in conjunction with the hydrostatic pressure of the shaft pipe - amounting in total to as much as 25 MPa - makes it possible to convey the stowing material for a distance 12000 m underground up to the workings without any need for additional booster pumps. Via a pipe installed in the face, the paste is pressurised into the cavities in the specially fragmented rock in the mined-out zone well behind the support. Consistent use of stowage of caved-in goafs makes it possible to reduce surface settlement above the workings. Fires in the stowed rock are either smothered or completely prevented thanks to the exceptional air-tightness in the caved goaf and the cooling effects of the slurry stowage. The reduced danger of fire, the preventation of air-leakage and the positive effects on gas emission from the coal improve safety in the workings.

Jan 1, 1998

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

By W. F. Moore

"In January 1981, Quintette Coal Limited (QCL) signed a 2a-year coking coal sales agreement with the Japanese Steel Industry which was followed by the commencement of mining operations in October 1982 and preparation plant operation in November 1983. During the mine 's startup, the town of Tumbler Ridge, the Anzac rail spur line, coal port facilities at Ridley Island plus numerous related elements of infrastructure were completed to support QCL and the neighbouring Bullmose operation in northeastern British Columbia. QCL's annual product coking coal levels have accelerated from 2.9 to 5.2 Mt between 1984 and 1986 with related increases in total mined volume from 14.8 to 41.0 M BCM between 1983 and 1986. This paper presents an overview of QCL 's current operation and related infrastructure. Development BackgroundDuring the 1970s, the Japanese Steel Industry (JSI) was forecasting a steady and significant growth in its steel production. By 1980 they were expecting crude steel production to increase from about 105 Mt in 1980 to 125 Mt by 1985 and almost 140 Mt by 1990.Discussions between Quintette Coal Limited (QCL) and the JSI for the development of the QCL project began in the 1970s and continued over a period of several years. During that time detailed and regular meetings took place, at which technical and commercial presentations were made to the JSI. The geology of the project area and the alternative mining methods and sequences were studied in detail. The new rail line which would connect the mine to tidewater was a critical factor and received particular attention. Alternate routes for the rail line from Tumbler Ridge to Prince George were the subject of much detailed study and discussions. The Anzac route was chosen in the best long-term interest of the northeast area development, after careful consideration and advice from the Japanese side.The new bulk coal terminal on Ridley Island at Prince Rupert was also a key factor and completed the development of an independent and new major coal field to supply the JSI. The QCL project and the development of the northeast area of British Columbia was a major strategical initiative of the JSI. It provided Japan with an important new coal field which was both self-sufficient and distinct from the traditional Japanese coal field resources in southern Canada, Australia, and the United States."

Jan 1, 1988

By B Walker, A Robertson, C Wels, S Fortin

A background characterisation study was carried out in the Sangre de Cristo mountains, New Mexico, to: quantify naturally occurring contaminant loads from mineralised areas; define site-specific background concentrations; and to determine key factors controlling spatial and temporal variations in contaminant concentrations. The study included a comprehensive sampling and testing program (paste pH/EC, ABA, leach extraction tests) of soil/bedrock from mineralised areas (including erosional scars), and a ground water and surface water quality monitoring program in selected mineralised watersheds. Results demonstrate that high concentrations of contaminants occur naturally in ground and surface water draining the mineralised area of the Red River basin. The erosional scars were found to represent the major source of acid rock drainage (ARD) (~66 per cent) in this area due to: high rates of weathering and erosion, which continually exposes sulfide-bearing outcrops; and high rates of run-off as a result of high elevation and lack of vegetation. The scar material is generally very acidic (paste pH ranges from 8.5 to 1.5; average = 3.6) with highly elevated concentrations of sulfate and leachable metals. The composition and concentration of leachable metals vary significantly, not only between scars but also within a given scar. While all streams draining the various scar watersheds are highly acidic, each has a characteristic æfingerprintÆ of sulfate and metal concentrations. Most of the run-off from the scars infiltrates into alluvial debris flow aprons and reaches the Red River via groundwater flow.

Jan 1, 2003

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

By B. B. Meadows

"The Minto-Chipman Strip Mining Reclamation Project was initiated to re-vegetate the spoil piles remaining from strip mining operations.All available information was studied by the team responsible, and areas being reclaimed in the U. S. were visited, Methods applicable to the N. B. Project were noted for future use.We have both surface and underground mining operations in New Brunswick, Both deface the natural landscape and reclamation varies in difficulty, Surface operation disturbances are the most difficult to correct.Some of the surface mining is carried out next to two main highways and the results are definite eyesores, With this in mind, it was decided to landscape the spoil ground next to the highways and plant “as is"" the ground remote from the public view.The landscaping entailed various degrees of bulldozing from complete levelling to contouring, smoothing and topping, Bulldozing is, of course, the most expensive part of any reclamation project.There are two phases to the planting program; experimental and operational--experimental both prior and, later, in conjunction with the operational planting.Initially in the experimental project, the pH and composition of the spoil was determined using a grid sampling system. Soil samples were tested in a laboratory at the University of New Brunswick."

Jan 1, 1970

By R. J. Mason

Background to the Transvaal Iron Age-new discoveries at Olifantspoort and Broederstroom R. J. MASON*, Ph.D. (Visitor) The work being done on Iron Age sites in the Transvaal is described, with particular reference to the finds at Olifantspoort and Broederstroom. The material so far found provides evidence for the production of iron and copper, the farming of cattle and sheep, and the construction of large villages by people who were probably ancestral to the present Bantu population. The material dates from as early as A.D. 270, but clear indications occur from AD. 460 onwards.

Jan 1, 1974

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997