Search Documents

By Frederick T. Williams

The purpose of this paper is to discuss the relative merits of the large 31/8-in. machine and the small 2 1/4-in. tappet machine in driving development-headings; and although the data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winzing. Recently we drove two parallel cross-cuts through the same formation, using a 3 1/8-in. machine at the breast of one crosscut, and a 2 1/4-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties, the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, the air-pressure or the experience of the operating crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to "pull " the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated andesitic or pho-nolytic breccia, true massive andesite, trachytic phonolyte, tuffs, and along dikes of decomposed basalt and hard phonolyte. In every instance a satisfactory record was made. The headings here describe? mere driven through highly indurated andesitic breccia, having a hardness of from 5.2 to 7.2 and a sp. gr. of from 2.2 to 2.8. The action of the breccia under the drill was not materially different from that of ordi-

Jan 1, 1907

By H. T. Morris

ONE of the chief concerns of the Bethlehem Steel Co. naturally is the proper functioning of its organization. This involves the training of a continuous supply of younger men to fill the vacancies caused not only by the inevitable departure of older men, but also by the growth of existing establishment, and by expansion in new directions. It does not oper-ate a student training course with a fixed time schedule or with definite periods of rotation through the differ-ent divisions. To state the case positively, the gradu-ate's training course must operate continuously from the beginning of his employment through a long term of years. No period of weeks or months nor pair of years suffice to bring him into contact with all the com-binations needed to qualify him for the larger destiny toward which we hope he is headed. Our first step in selecting a college man is to require that he have a degree. We thus approximate the assur-ance that at least four annual siftings have reduced the chance that a non-worker may find himself in a job where work is necessary. The next step is to try to ascertain facts, from the graduate and from others who have known him at his home and in 'his college, to indi-cate whether our opportunities offer him a career that will challenge his continuing interest, and hold him to tenacious effort against all happenings. We aim to avoid knowingly bringing into our organization a man who will not develop in it enough enthusiasm to keep him happily striving. Having made our selections, we assemble the gradu-ates into a probationary observation circuit. We-put ourselves under their observation by taking them in small groups, usually of two to four men, on a circuit of every part of the Bethlehem plant, in which every manufacturing principle of our steel business is ex-emplified. The probationers work at something from day to day, with their hands if it can be arranged; otherwise in questioning, examining, and note-taking. Their observations include talks with superintendents, foremen, and workmen, the conditions under which workmen labor, apparatus, machinery, methods, design and operation of plant.

Jan 7, 1928

By F. G. Miller, E. B. Wilson

In 1972, coal mine productivity was in steady decline and labor and maintenance costs were spiralling upward. Yet, despite this sad state of affairs, nowhere in the US at that time was there a comprehensive and coordinated coal research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. It was during this period that Bethlehem Steel Corp. determined that a new approach to coal mining research was needed for the industry as well as for the company itself. After studying Bethlehem's own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, a comprehensive research package was presented to company management in late 1972. The ideas and experience of many operating and management personnel in the company contributed to the formulation of the final plan as approved.

Jan 10, 1976

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By LeRoy Kienitz

There may be someone here who is not required to run his equipment at its maximum capacity. There may be some fortunate enough to have more crushers than needed, wider conveyor belts than required, and other mill equipment equally oversize. If so, then this paper will have no interest for him; but if most of you are in the situation we in the aggregate producing industry are in, then you probably wish to crowd your mill equipment to its limit. When you do this you must watch for block-up and overloads of all sorts. You need more eyes than you have to guard the critical points. The human eyes that now do nothing much, but watch should be freed for more productive work.

Jan 1, 1961

By Graham Walker

A new Code of Practice for the brake performance of off -highway vehicles was established in Alberta in 1976. Vehicles loaded to gross vehicle weight must be capable of stopping with mechanical brakes five times in quick succession on a grade of 10 per cent from a speed of 28 miles per hour. Comparative trials of various brake systems have been carried out and some combinations capable of meeting the Code are identified. Some problem areas in truck braking are reviewed and potential developments indicated.

Jan 1, 1977

By James Thompson

Mine planning at Consolidation Coal Company's (Consol) Glenharold Mine in North Dakota is being constrained by environ¬mental concerns that did not exist when the mine opened in 1965. One such concern which developed in the mid-1970's is the impact of mining on woodlands that are considered impor¬tant wildlife habitat. To better coordinate mine planning with permitting, a cooperative task force was created to evaluate woodlands for their wild¬life habitat potential. The task force included representatives from Consol and state and federal agencies. This cooperative process is seen as a method of communication between industry and government and as a way of developing decision-making tools for mine planners and regulatory agencies.

Jan 1, 1981

By R. L. Curfman

WHEN the Uranium Reduction Co. mill was put on stream in October 1956, one of the many operational problems was that the sand-slime separation circuits could not produce a satisfactory RIP feed, inasmuch as production greatly exceeded de- sign capacity. The original cyclone portion of the circuits consisted of two stages of three 14-in. cyclones in each circuit, as shown in the condensed flowsheet. The high percentage of +325 mesh material in the over- flows of these 14-in. cyclones was not consistent with good operation, and flow rates per ton of ore were high, indicating that not enough of the total solids in the ore was being rejected as sands. It was inferred by members of the metallurgical department that returning the underflows, or sand fraction, from these cyclones back into the drag classifiers was the primary reason for dirty feed.

Jan 7, 1958

Inadequate understanding and/or assessment of technical and economic risk associated with geological uncertainty are key reasons many mining projects do not achieve forecast profitability. In the last 20 years many new and existing mines have experienced geology related problems, including lower than planned development and production rates, geotechnical/stability issues, unplanned dilution, ore loss, reduced metallurgical performance, environmental management concerns and unbudgeted capital/operating costs. Greater emphasis on the evaluation and communication of uncertainty associated with geological interpretations for feasibility and operations management results in better decision-making. The outcome of better decision-making is more efficient mining yielding enhanced financial returns for the mining industry.

Jan 1, 2009

By N. Staroselsky

"Significant energy savings are often possible for centrifugal compressors operating in parallel by improved control strategy and improved instrumentation. Blow-off can usually be reduced by improved surge control combined with a better control strategy for loading and unloading the group of machines. More precise and stable pressure control then becomes possible. This improved control strategy will also decrease the frequency of operation near the dangerous limits of surge or overload or overspeed. A sample station of mixed centrifugal and reciprocating compressors is examined and a substantial energy saving with the recommended control strategy is projected from operating data. Present Operating Conditions of the Compressed Air StationThe Compressor StationThe compressor station described here has three centrifugal compressors and three reciprocating. It supplies a mine in New Brunswick.Compressed Air and Power ConsumptionFigure I and Figure 2 provide graphs of air consumption and pressure changes based on the owner's data.During the typical two-shift operating day (Fig . I) in the non-productive shift (midnight to 8:00 a.m.), the consumption stays at a level of 9,000 SCFM. This corresponds to a pressure of 110 PSIG. Then, after 8:00 a.m ., the air consumption starts to increase and th e pressure decreases. Around 10:00 a.m., the consumption reaches its maximum level at 97 PSIG. Around II :30 a.m., the air consumption starts to decrease because of the production drop during the lunch break of the first shift. Pressure increases again up to 109 PSIG. After the break, consumption rises to its maximum level over 16,000 SCFM andpressure drops to 97 PSIG.Around 2:30 p.m., the air consumption drops sharply to 9,000 SCFM because of the production decrease to zero level. This drop results from changing of shifts. The pressure at this time increases again up to 110 PSIG. The second shift (2:30 to II :30 p.m.) is an alogous to the first.During the three-shift operating day, the break around 4:00 . a.m . and the shift change around 6:30 a.m. cause sharp drops in air consumption. The pressure for almost the entire night shift stays near 110 PSIG because the station is working with blowing-off even under the maximum consumption. The analysis of Figures I and 2 shows that the pressure varies with the air consumption changes. During non -productive time (non-production shifts , shift changes and breaks) or during the night shift, the total station capacity is proportional to the discharge pressure. By decreasing the level of this pressure up to 97 PSIG, the flow of the station may be decreased during the non-production time as follow s:"

Jan 1, 1980

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

By Norman O. Lotter

The problem of quantifying the full performance potential of an ore body in a concentrator, and how to configure a flowsheet to achieve that potential, either for a new operation or an existing one, is a strategic challenge. Modern flowsheeting technology that has been developed over the last twenty years has provided a suitable platform to achieve this. The integrated use of geology, compositional and quantitative mineralogy, sampling models, quality controls, and mineral processing, including flotation testing, has evolved into what is now called process mineralogy. Two specific tools have been developed and validated as standard methods in this toollbox. These are statistical benchmark surveying and high-confidence flotation testing. Both of these have borrowed from the sampling theories of Pierre Gy and from geostatistics. Additionally, they work on a replicate measurement and averaging basis, thus reducing the overall random error level. With this arrangement, one is in a position to characterize the ore from true samples and identify and quantify the economic minerals present in a manner that easily brings out the processing implications and likely grades and recoveries. In particular, the approach captures the variation in the ore body, which, if properly translated into the flowsheet design, minimizes the risk that unexpected responses will develop in the concentrator operations. A further advantage is that successful plant trials are now possible and practical. An overview of this approach is presented with two case studies.

Jan 1, 2011

By D. M. McFarland

IN mining, quarrying, and construction, drilling and blasting have an important influence on the operations that follow. If the fragmentation of material being disrupted is inadequate, loading and transportation equipment will not operate at or near full capacity. Any operator faced with this difficulty should not be satisfied until he is convinced by a careful study of his methods of drilling and blasting that no improvement can be made. Rock in a certain quarry in Ohio seemed to defy any grade of explosive or means of detonation that the explosives industry had to offer. The average result of a blast was that a great part of the burden would be pushed out from the face in a number of large sections that would jokingly be referred to as "boxcars." These were no credit to the explosives man and a costly problem for the quarry company. Such blocks retard shovel operation as they have to be uncovered and subjected to secondary drilling and blasting which, if extensive, is an expensive operation. It was an attempt to improve the fragmentation obtained in primary blasts that led to the development of milli-second-delay electric blasting caps. The reasoning that prompted the trial was that even with wide spacing of the drill holes it seemed that the burden was separated too quickly from the face by the cutting action of the explosives from hole to hole. If the time of firing of the holes could be regulated so that

Jan 1, 1948

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The Engineering Department started a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore the Crush and Convey and Ore Control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, Drill Energy Index and databases, we have been able to improve fragmentation size and verify the results while controlling costs.

Jan 1, 2011

By George A. Miller

AMERICANS like engines, but more than anything they like powerful engines, and next to that they want them quiet, silent, smooth; perhaps a slight purr might be permitted, but they must not knock. To provide a gasoline to fit all these requirements, American petroleum technologists have experimented for years, and mounting octane numbers of the gasolines the refiners have produced both before and during the war bear witness to their success. The question on everyone's mind now is what may we expect in the way of engine fuel in the postwar period? The gasoline drouth during the war rationing, the inconvenience of doing without a car were major annoyances to all motorists, but they put up with them pretty cheerfully for the most part. However, now that the war is over, and the jalopies are all out and the better cars have been taken off the jacks and brought out on the road, the call is for "Some of that good gas-fill her up, if you please."

Jan 1, 1945

By D. A. Mackie, J. E. Rider

"Good belt conveyor design is the most often neglected detail in the engineering of a plant. This results in downtime from spills or jams and premature failure of equipment components. Careful layout and component selection will result in better operation, a cleaner plant and therefore lower maintenance costs.IntroductionDespite the availability of many excellent sources of data on conveyor design, such as the Conveyor Equipment Manufacturers' Association (CEMA) Manual, ""Belt Convyors for Bulk Materials"" , there continues to be repetitive errors made in design. Why? Certainly, there is no substitute for experience, but largely, classical errors in belt conveyor design is rather elementary and so the temptation to have the work done by relatively inexperienced designers is great. What that does is develop "" experienced"" designers who become incompetent through no fault of their own. It is hoped that this paper will supplement available design data, help those who are "" put into"" a design situation to better cope with their predicament, and ease the lives of plant maintenance personnel."

Jan 1, 1990

By Richard D. Moffett

The MineSight® Implicit Modeler arms geologists, engineers and surveyors with a better approach to 3D modeling. Use the tool to quickly retrieve a 3D wireframe from drillhole data and onscreen interpretation. Generate faster and more informed decisions to guide future work and improve reproducibility of results. Implicit Modeling is a mathematical surface fitting method that interpolates points to give a smooth and realistic fit. Control results by mixing planar, sectional and non-orthogonal polygons or polylines, as well as drillhole information to create solids or surfaces. The outcomes are particularly valuable to identify ore body trends, generate 3D contours of drillhole intercepts, or produce cut-off 3D maps. MineSight Implicit Modeler (MSIM) is fully integrated in MineSight?s robust and versatile suite of products, allowing you to interpret, interpolate and calculate while moving between applications. It connects seamlessly with the MineSight Torque SQL database, offering access to extensive filtering options. MSIM makes modeling much faster, allowing geologists more time to analyze data and test theories. The presentation will reveal how MSIM complements MineSight?s geomodeling workflow.

May 1, 2013

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By L M. Zhang, X Y. Li

Surface displacements are routinely monitored at multiple points during slope excavation. The monitoring data reveals the safety status of the slope under current loading conditions. They can be used to enhance the prediction of the future performance of the slope by reducing the uncertainties of the prediction model and its model parameters. In a multistage excavation, the observed displacements in the current stage can be used to update the prediction of the displacements in subsequent stages. Besides, due to the spatial correlation of the slope parameters, the prediction of the displacement at one location can also be updated using the monitored displacements at adjacent locations. This study aims to develop a multistep updating method to enhance the prediction of the future performance of the slope using time-series monitoring data at multiple points. This method integrates the theoretical computational model with observational evidence. It considers the inherent uncertainty of the slope, model uncertainty and measurement uncertainty. With more monitoring information being incorporated, the prediction becomes closer to the actual performance of the slope. A case study of a multistage excavation of an extremely high rock slope in south-west China is presented for illustration.CITATION:Li, X Y and Zhang, L M, 2014. Better prediction of performance of a slope using time-series monitoring data at multiple points in a multistep excavation, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 183–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014