Search Documents

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

By Kenneth N. Han, Peter Nam-soo Kim

A kinetic model for leaching of particulate metals in a batch system has been developed. The leaching mechanism has been analyzed by solving a series of ordinary differential equations relating heterogeneous reaction kinetics at the solid/liquid interface to mass transfer of reactant and products. Special emphasis has been given to the effect of changing of the surface area of the leaching substrate and initial particle distribution on the overall leaching rate. The dissolution of gold powders in acidic solution with bromine as an oxidant has been used as a model system. The effect of particle size, chemical reaction order, rate constant and mass transfer coefficient on the overall rate of dissolution of metal powder has been analyzed and discussed.

Jan 1, 2005

By K. N. Han

A kinetic model for the batch leaching of various metals using different lixiviants was developed. The overall material balances for the reactants and products at the solid/ liquid interface were formulated for various types of heterogeneous reactions at the interface. The solutions to these mass balances are identified analytically, as well as numerically. Applications of these numerical solutions to various leaching systems using rotating discs or powders are discussed. The metal-dissolution systems addressed include cobalt, nickel and copper in acid, cyanide and ammoniacal solutions.

Jan 1, 1996

By X. Meng

A kinetic model for batch leaching of various metals with different lixiviants has been developed. Overall material balances for reactants and products at the solid/liquid interface were formulated with various types of heterogeneous reactions in place at the interface. The solutions to these mass balances have been identified analytically as well as numerically using a Runge-Kutta method. Applications of these numerical solutions to various leaching systems using the rotating disc or powders have been discussed. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1994

By K. Fumimura, T. Nishimura, M. Kohno

When applying numerical techniques to problems of deformation of rocks, the body to be analyzed is divided into small portions and is represented by a system of points linked together with the neighboring points. In the so-called distinct element modeling, the particles in the system are directly connected by springs and a contact law is used to specify forces on the particles to simulate the mechanical behavior of the body. The relation between the spring stiffness and commonly measured material properties, such as the Young’s modulus and the Poisson’s ratio, should be known a priori. For the general case of a random packing of particles, the relation is found by means of a process in which a system of particles and set of parameters are prepared to simulate a set of specimen-size test and then the input parameters are chosen to match the measured material properties. The validity of the numerical result is only demonstrated by comparison model behaviors with the measured responses. The process includes trial-and-error manner, therefore, no model is complete to reproduce the mechanical properties. In this paper, a relation between the spring stiffness and the elastic constants; the Young’s modulus and the Poisson’s ratio, is introduced to a three-dimensional distinct lattice spring method. Two simple numerical examples will be presented to demonstrate the performance of the method with the procedure for the determination of the spring stiffness.

Jan 1, 2015

By K Schonert, K Eichas

Electrostatic separation of non-conductive materials can be accomplished by triboelectric charging. The efficiency of convential separators becomes worse in the size range below about 100 ¦m. These problems are solved by developing a new double-drum-separator. The investigations have shown the possibility of separating very fine mineral mixtures (eg quartz/calcite) in a strong electric field after tribo-charging in a special dust-feeder. The paper reports about the influence of particle size and field intensity on the separation and deals furthermore with the problem of desagglomeration.

Jan 1, 1993

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A. T. Schwennesen

(Wilkes-Barre Meeting, June, 1911.) EVERY engineer has occasion to trace or copy a map, plan, or other drawing on paper too thick for the ordinary way of using tracing-cloth or tracing-paper. When the figure is small and simple a copy may be made by holding the original against a window-pane, covering it with the paper, and tracing direct by the aid of the strong sunlight from outside. The need of utilizing this principle on a larger scale and in a more convenient position led Dr. J. C. Branner to plan the table of which the following is a description: This table was first made in the form of an adjustable glass-top table with a mirror beneath, in 1887, while Dr. Branner was State Geologist of Arkansas. Later it was modified as experience suggested until the form as here described was evolved. The device consists essentially of a drafting-table with a plate-glass top, upon which the original drawing and the paper are laid, and a mirror mounted underneath to reflect the light of the sky up through the drawing. The glass top is hinged and fitted with two arms and thumb-screws, so that it can be raised and fixed to any position, either inclined or horizontal. The mirror is pivoted and revolves about a horizontal axis, so that it may be tilted to any angle. The hood of cardboard or black cloth prevents the reflection of light from the tracing, and may or may not be attached to the table. The apparatus is set up before a window through which part of the unobstructed sky is visible. The mirror is then adjusted like the reflector of a microscope, so that the skylight is reflected up through the drawing. If the mirror can be so located that the direct rays of the sun are reflected through the drawings, thicker paper can be used. The map or drawing may be held in place by clips screwed

May 1, 1911

By M. R. Anderton

"A hierarchical four-character code designed for geological and allied data may be used to log exploration drill-holes and store the information on magnetic media. The code is intended for use in semi-free format and permits the collection of as much, or as little, data as the geologist may require for the purpose in hand. A method of data storage by variable length records is discussed.Information may be retrieved by means of a simple enquiry language. Optional output facilities could allow the retrieval of data in a form suitable for direct input to a contouring package. The enquiry parameters and interrogation program can thus provide the interface between the data bank and associated application systems."

Jan 1, 2014

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By Pete G. Kovalchik, Lynn A. Alcorn, Rudy J. Matetic, Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage is comprised of seven different types of machines. The continuous mining machine is first among all the equipment with 35% of the noise overexposures. The ational Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce excessive exposure for operators of continuous mining machines and preventing additional cases of oise Induced Hearing Loss (NIHL) by developing low-cost retrofit noise controls for mining equipment. This paper describes a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 26.4% and 27.4% noise exposure reduction for the continuous mining machine operator. This research is providing the mining community with an additional noise control to be utilized on continuous mining machines, therefore reducing operator noise overexposure. Utilizing this newly developed noise control, along with previously proven controls for the continuous mining machine chain conveyor, will provide operators of these machines an opportunity to be within the MS HA-Permissible Exposure Limit (MSHA-PEL).

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

The modern resource extraction enterprise is a complex capital intensive business operating in a world of constantly evolving social, environmental and economic scrutiny. Investors, government, media and special interest groups expect to see business environmental and social performance respond and deliver increasing corporate responsibility and sustainability.   Thorough interrogation of business performance using a multi-disciplinary due diligence approach presents a more sophisticated review and benefits beyond the traditional compliance/conformance 'audit' style assessment.   Using a due diligence approach allows assessment through a comprehensive lens which examines potential short- and long-term risks including sometimes less tangible environmental and social liabilities, and informs management, investors and regulators of broader business performance. This approach provides information in a form that business can measure performance in a repeatable and enterprise wide sense.   This paper provides an outline of the due diligence process applied in this way, drawing from lessons learnt and industry based experiences in the due diligence process and the benefits and tools that can  be applied in an environmental and social due diligence business performance assessment

Jun 1, 2010

By S. Huang, K. Xia

"During crushing, rock particle is subjected to complicated loading and the particle shape influences the fragmentation outcome. Thus, a highly controlled laboratory test is desired to establish the relation between the loading and the fragmentation parameters for better understanding the rock crushing mechanism. In this work, a split Hopkinson pressure bar system in combination with high speed cameras is utilized to carry out a dynamic ball compression test, in which the spherical rock sample is adopted to avoid the shape effect. Using the elasticity theory, the history of the axial symmetric tensile stress perpendicular to the diametrical direction along the loading axis is determined, from which the loading rate and the dynamic indirect tensile strength are calculated. With the aid of the moment-trap technique, the total energy absorbed by samples is accurately determined from the one-dimensional wave analysis. Furthermore by considering the kinetic energy of the sample fragments using the high speed camera snapshots, the surface energy is determined for each sample. The relations between the loading rate and the fragmentation parameters, i.e., the number of fragments and the surface energy are established. The application of this method to a granitic rock shows that it is flexible and can be applied to the crushing study of generic brittle solids. INTRODUCTIONCrushers are widely used to break rocks to extract specific minerals in the mining industry, and to obtain rock fragments with desired size distribution in construction industry. During crushing, the breakage of particles can be in either the single-layer mode or the multi-layer mode. In the single-layer mode, the particle breakage can be assumed to be isolated, in which the interaction between particles can be ignored. It is thus suggested by many researchers that highly controlled single particle test should be performed to establish the relation between the input mechanical energy and size reduction for better understanding the crushing mechanism (Yashima et al., 1987; Tavares, 2007; Pitchumani et al., 2004)."

Jan 1, 2015

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab's Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By G Fergus, M Hart, S W. Weeks

Rio Tinto Alcan has undertaken feasibility level assessments into the expansion of its bauxite mining operation in an area south of the Embley River in far north Queensland. The project has the potential to extend their Weipa operations by approximately 40 years.The construction and operation of two additional mineral ore processing plants are proposed for the South of Embley project. Golder Associates was engaged to develop and conduct modelling assessments of potential sources of water supply required by mineral ore processing.Two models were developed using GoldSim: a dam yield model and a water balance model. GoldSim is a graphical object-oriented modelling environment with a capacity to carry out dynamic probabilistic simulations. Originally developed by Golder, GoldSim has been applied successfully in a decision support role to a range of mine water management operations.The dam yield model was used to provide estimates of reliability and volume of annual water supply of several potential surface water dams. This information was then used to determine a hierarchy of water supply options for processing plant operations. The water balance model dynamically simulated the water demands of the two production plants and the consequential response in water supply, with respect to the timing and discharges provided by the various source options.Use of the model provided a preliminary operational tool to assist with water supply management decisions. Water quality issues required a blending of water from separate sources and attention paid to scheduling to ensure water supply through the dry season. The model also helped identify risks to water supply in the event of underperformance of one or more water supply sources. This allowed the operational rules to be refined to minimise those risks.The dynamic and stochastic modelling approach provided a method for identification of water supply issues susceptible to seasonal climate variability.CITATION:Weeks, S W, Hart, M and Fergus, G, 2013. A dynamic evaluation of water supply security susceptible to climate seasonality, in Proceedings Water in Mining 2013, pp 197-208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Walter C. Labys, Fereidoon Shahrokh

This paper presents an application of computer simulation methods to the modeling and forecasting of the United States coal market. The computer methods employed as well as the model constructed are based on economic and econometric theory. The contents of the paper include a description of the coal market, the corresponding computer model, tests of model validation, computer generated scenarios for the period 1980-1985, and comparisons of the scenarios generated with that of other major coal forecasts.

Jan 1, 1983

By Reid K. J, Restarick C. J

The breakage and flow characteristics of quartz, ground as a minor constituent with calcite in a continuous wet ball mill, have been determined by carefully controlled grinding tests.A mathematical model, combining the simple functions which describe these characteristics, has been used to predict both steady state and non steady state results.The calculated results are compared with experimental data.

Jan 1, 1966