Search Documents

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By R McIlwraith, B Breul

Two case studies are presented in this paper. The first one discusses a roller compacted concrete water supply dam that was constructed in El Mauro in Chile to provide water for agriculture activities downstream of a copper mine during the dry season. The 23 m high dam used a bituminous geomembrane (BGM) as the low permeability upstream facing element on the dam to control seepage through the dam. This is the first time that a BGM has been used in this application. A deep cut-off trench was used to control seepage beneath the dam and through the abutments. This paper briefly presents the design of the dam, including selection of the concrete mix and maximum aggregate size that the use of the Coletanche BGM allowed, and provides details of the construction, quality control and assurance of the installation of the BGM. An ultrasonic apparatus was used as part of the quality control on the BGM seams.The second case study discusses a tailings dam in Cerro Lindo, Peru (near Chincha), where a watertight BGM was installed on the upstream face. Results are presented of the survey done by a consultant on the behaviour of the dam and in particular of the BGM following an earthquake of magnitude 8.1 in Chincha close to the site. These findings on-site were checked by trials in a laboratory in California. Test results are given and explained.CITATION:Breul, B and McIlwraith, R, 2015. Case histories – roller compacted concrete dam waterproofing with a bituminous geomembrane in Chile and a tailings dam in Peru subject to an earthquake of 8.1 magnitude, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 367–372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By R. E. Martin

"The Westerose Leduc (D-3) pool, a Devonian reef reservoir situated in Central Alberta, Canada, has now been producing for over seven years. As a unit operation, the pool pro-vides an interesting example of the full exploitation of gravity segregation tendencies. The reef has a 238-foot oil column, underlain •by bottom water and over-lain by a substantial gas cap. The original hydrocarbons in place were 147.96 million STB oil and 94.4 MMMCF of Taw gas cap gas. Nine-teen producing wells on 80-acre spacing have been completed, most of which are highly productive. Gas injection operations return solution gas to the gas cap. A study of the rock and fluid properties of the pool show it to be conducive to production by gravity segregation at high rates. Monthly average producing rates have varied between 800 B/D and 8,000 B/D and have recently totalled 3,000 BID to 5,000 B /D. Recovery and performance predictions under partial pres-sure maintenance at 10,000 BID indicate an ultimate recovery of 66 per cent of the original oil in place. In the absence of pressure maintenance, recovery would be only slightly less."

Jan 1, 1960

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By L. A. Pursell

Environmental constraints can both delay and raise the cost of a major plant addition, often requiring a complete reevaluation of the plant site and the proposed project. In this case history, steps are presented which were followed in applying for environmental permits for a major addition to a lime plant. Methods are described for determining expected emission increases and for selecting the best control technology for each source. The description progresses through pre-application conferences with control agencies, the formal application procedure, computer modeling the air quality impact, and the methods followed in obtaining a favorable determination.

Jan 1, 1983

By D. Crone, T. Watts

"The Lindsley project was a program of deep drilling to test the contact down-dip from two nickel-copper deposits, one uneconomical and the other mined out. The role of Borehole Pulse EM(PEM) was to detect the higher grade, more massive sulphide zones if they were missed by a drillhole, and to help determine geometry if the zones were intersected. Two problems appeared as the PEM survey progressed: (1) conductivity-thickness as measured by the PEM did not always relate to economic sulphides as determined by the market; (2) a pattern of unusual PEM anomalies was obtained that indicated something odd and big, but the cause was unknown. A large fold structure subsequently was indicated by a program of deepening previous holes, the third of which intersected high-grade mineralization below 1280 m. Falconbridge is in the process of shaft sinking and underground exploration.IntroductionThe Falconbridge Lindsley property is on the south rim of the Sudbury basin, 8 Ian north of downtown Sudbury. The original property was acquired by a prospector named James Stobie, who, in early August 1885, staked a showing that later became the Mount Nickel mine (Fig. I). On August 10 Stobie staked another property that would become the Little Stobie mine, and at the end of the same month he staked the main Stobie orebody.In 1888, the ground immediately west of the MOlU1t Nickel find was staked. This ground contained the Blezard deposit (Fig. 1) which was put into production in 1889 and was eventually acquired by Inco. Down-dip from the Blezard workings, on Falconbridge ground, is located the upper Lindsley No. 1 deposit which was drilled off by Falconbridge in the 1940s to 1950s. A decision to go underground on the Lindsley No.1 mineralization was made in 1969, but the project was cancelled in 1971 because of declining nickel prices. The shaft was stopped at 95 m, and the headframe and hoist were sold. Further surface exploration drilling in the 1970s discovered the deeper Lindsley No. 2 zone, but as it had grades similar to those of the No. 1 zone, it too was considered uneconomic."

Jan 1, 1992

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By Jay Jones, William D. Rech

The Henderson Mine developed a water treatment system in 1985 to meet the NPDES requirements for its mine water discharge. Unacceptable levels of Zinc and Manganese formed the basis for the design and operation of the treatment system. Since initial start up, this system has reliably removed metals from the mine water and facilitated low cost compliance with water standards. The potential addition of a bio- monitoring requirement to the NPDES Permit in 1990 has added a second dimension to the metals removal process. This paper will review the history of Henderson's success at developing a low capital treatment system for metals removal and the anticipated effects of bio-monitoring upon this system based upon preliminary bio-monitoring screening.

Jan 1, 1991

By McKenzie A. M

The Corridor ore body is so named because it occurs in an east-west zone or corridor of schist bounded on the north by the siliceous conglomerates of Mount Lyell, and on the south by similar conglomerates of the Tharsis ridge (Fig. 1). It was discovered after the geophysical prospecting methods described below had defined a target zone for diamond drilling.Since the proving of copper mineralisation by drilling, the corridor orebody has served the vital function of a convenient known target body for the orientation of more recently developed geophysical methods. Traversing of the orebody by these new methods has provided experience for the evaluation of anomalies elsewhere.Some of the methods applied had not been used in Australia before, and were introduced to the west coast of Tasmania through the undertaking there of modern regional exploration programmes. The authors feel that the information gained could be of assistance to others engaged in geophysical prospecting.HISTORY OF DISCOVERYProspecting in the Mount Lyell district has been more or less continuous since 1881. The first geological report was published by Thureau (1886).In 1934, Blazey and Douglas (1934-38) commenced geophysical surveys at Mt. Lyell using the equipotential method.They obtained anomalous indications in several discrete zones and actually detected the south-east half of the corridor orebody but their work never became the basis for...

Jan 1, 1961

The Hishikari gold deposit, discovered by the Metal Mining Agency of Japan, has become a giant class epithermal gold deposit with the highest grade of gold yet recorded in the world through detailed exploration and development by the Sumitomo Metal Mining Co Ltd. The exploration strategy involved a regional approach combining geological and gravity surveys over a 900 km2 area which had historically produced over 120 t of gold. These surveys were carried out to grasp the common geologic features of epithermal gold deposits in the survey area. A genetic model for epithermal gold deposits in the area under regional survey was also considered based on detailed research of the Kushikino epithermal gold deposit which was in operation at that time. This model was applied to the targeted areas, and important relationships between mineralisation, host lithology, intensive propylitic alteration and gravity highs became apparent. The Hishikari block was selected in this way and bonanza gold was discovered during drilling. Since the development of the Hishikari mine, information useful for further exploration for the same type of deposit has been accumulated.

Jan 1, 1995

The Hishikari gold deposit, discovered by the Metal Mining Agency of Japan, has become a giant class epithermal gold deposit with the highest grade of gold yet recorded in the world through detailed exploration and development by the Sumitomo Metal Mining Co., Ltd. The exploration strategy involved a regional approach combining geological and gravity surveys over a 900 km2 area which had historically produced over 120 t of gold. These surveys were carried out to grasp the common geologic features of epithermal gold deposits in the survey area. A genetic model for epithermal gold deposits in the area under regional survey was also considered based on detailed research of the Kushikino epithermal gold deposit which was in operation at that time. This model was applied to the targeted areas, and important relationships between mineralization, host lithology, intensive propylitic alteration and gravity highs became apparent. The Hishikari block was selected in this way and bonanza gold was discovered during drilling. Since the development of the Hishikari mine, information useful for further exploration for the same type of deposit has been accumulated.

Jan 1, 1995

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46º 31' north latitude, 67º 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sulfide deposits of the Bathurst-Newcastle district.

Jan 1, 1958

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006

By Allan Sylvester

This paper will discuss the design, construction, and performance of the support of excavation on the San Diego State University LRT Station. The vertical elements of the system include drilled secant piles and drilled soldier piles. We will discuss the geo-technical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the pile and support of excavation systems. In consideration of the conference theme, there will be a discussion of the successful accomplishment of meeting the interim milestone dates of the Contract. The project team cooperatively worked to design and install approximately 1,100 drilled secant and soldier piles as well as excavate and install the balance of the support of excavation elements in such a manner as to minimize the disruption to campus students and operations.

Jan 1, 2002