Search Documents

By F H. Henrfquez, A G. Oroz

Design and operating conditions of large size mechanical flotation cells were evaluated by comparing them with actual operating conditions in a plant. The objective was to determine the time scale-up factor, typically based on empirical rules. Experiments were conducted on the rougher flotation circuit at Minera Escondida Ltd. The circuit consisted of self-aerated mechanical cells of 160 m3, arranged in six parallel banks with nine cells each. The rougher circuit flotation kinetics were evaluated from direct sampling and local mass balances around each cell of the bank. Adjusted overall mass balances were also developed. This information was used to fit different kinetic flotation models, and it was found that the rectangular distribution function was the most appropriate to describe the distributed rate constant for industrial operation. Then, a rougher flotation simulator was developed to describe the actual operation in terms of the operating variables (mass flowrate, solid percentage, feed grade) and the actual volumetric flowrate entering to each cell. In this study feed pulp samples were taken in parallel from the rougher circuit and were simultaneously floated in the laboratory. The kinetic behaviour was then modelled at a laboratory batch scale in order to determine the time scale-up factor between laboratory batch flotation data and industrial size flotation. The time scale-up factor observed for large sized cells, 160 m3, was found to be reasonably similar to those previously determined for self-aerated mechanical cells, but of lower size, operating at similar recoveries. In addition, the relative effect of mixing, between laboratory batch and an industrial flotation bank, was quantified by the parameter, separating the impact that kinetic and mixing changes have on the time scale-up factor. In general, the rougher flotation operation was found to reach the predicted metallurgical target, and the optimal separability criterion was also respected. The diagnostic generates information about the internal state of the process and helps to identify potential improvements for design, operation and control of the circuit.

Jan 1, 2005

By R Salmimies

Choosing a ceramic capillary action filter is often favoured in processes where low energy consumption is important, such as the dewatering of iron ore. In addition, the performance of the filter medium is essential, and the possibility to regenerate the medium is an advantage compared to other types of filter media. Although low, roughly 8 - 9 w-per cent for iron ore concentrate, and even cake moisture is the primary goal of dewatering, the introduction of better filtration processes can result in significant improvements of water economy and material efficiency.As industrial beneficiation processes are often complicated in their chemistry due to impurities originating from the ore itself, from the up-stream processing equipment and from the process water used, the characterisation of the filter media after usage might provide relevant information on what actually takes place during long operating periods. The aim of this study was to obtain new information on the fouling of fi lter media in an iron ore process to enhance and develop the regeneration process of the media in the future.X-ray diffraction and scanning electron microscopy were used to characterise ceramic filter media used in the dewatering of magnetite. Principal component analysis and discriminant analysis were introduced to identify trends in the data. Two types of media blockages were found to play an important role in an acidic iron ore dewatering process: fouling by slurry particles and by in situ crystallisation of a calcium compound, of which the latter originated from the combination of process water and process chemistry.

Jul 11, 2011

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Characterisation of Manganese Ores

Sep 13, 2010

By J T. Woodcock

This paper discusses characterisation techniques that can be applied to complex waste products from metal production and processing operations with the aim of devising treatment methods for upgrading the metal content for recycling. Two waste streams were selected to illustrate the role of characterisation in adapting mineral processing techniques to provide an effective recycling strategy. Waste products chosen were:aluminium dross, which contains metallic aluminium particles in a coarse matrix of many components; and steel shredder sludge that contains copper wire and other metallics in a matrix of plastic and natural fibres, iron oxides, metallic iron, and other compounds. Characterisation methods discussed include chemical analysis (XRF, ICP-AES, and selected specialised techniques), phase analysis (XRD, SEM, TEM, and optical microscopy), morphology (IFESEM), sizing analysis (screening, Cyclosizing, Infrasizing, Malvern sizing), and general techniques such as particle shape, surface area, and porosity determinations. The applicability of these techniques to the waste products is considered in relation to their advantages and disadvantages, and sampling issues.Treatment techniques considered for the two waste products included comminution, screening, air or water classification, simple water leaching, gravity separation, magnetic separation, flotation, and eddy current separation.Tentative flow sheets were developed for the two wastes. For aluminium dross, it was proposed to use fine crushing followed by water washing to remove soluble chlorides and aluminium nitride, and then desliming followed by flotation of the granular fraction to give a metallic aluminium-rich concentrate. For shredder sludge, it was proposed to use wet screening, water classification, and gravity concentration to produce a copper-rich product and magnetic separation to produce a metallic iron-rich product.

Jan 1, 2004

By Mackinnon I. D R, Glikson M

Samples from the Callide Coal Measures, Queensland, Australia, containing the minor maceral, micrinite, have been studied using optical and electron-optical techniques to determine the precise compositional and structural nature of micrinite when in association with vitrinite macerals. Emphasis has been placed on direct spatial correlation of optical and electron-optical data due to the fine grain size (90 per cent of the component) and, as such, should not be considered a maceral.

Jan 1, 1991

By C K. Suzuki, J A. Yanaguizawa, D M. F de Santana, L R. P Leite, A H. Shinohara

In the present work, the microstructure and mechanical properties of structural mortar from glass insulators were studied by X-ray fluorescence, X-ray diffraction, infrared spectroscopy, microhardness and compression testings. The investigated glass insulators were manufactured between the 1960 and 1990 years and had been used in 230 kV transmission lines. The results evidenced that the structural mortar of glass insulator was replaced from Portland to aluminous cement along the years. The crystalline phases of the mortar were identified and mechanical properties were correlated.

Jan 1, 2008

By J Cortinez, P Vallejos, J Yianatos, M Rodriguez

Nowadays, one of the main problems in current flotation plants and new projects is the significant decrease in feed grades and changes in the mineral composition, which has an important effect on the mineral liberation and associations. Additionally, flotation plants usually operate with feed throughput higher than the original design, which has a significant impact on the feed particle size. All these conditions affect metallurgical performance, and must be evaluated and addressed, by improving control strategies for banks optimisation. For this purpose, the flotation of valuable minerals along the circuits requires better understanding, considering the compromise between performance and selectivity in flotation circuits. This paper presents a characterisation of the different minerals recovered along industrial flotation circuits. Plant sampling campaigns, performed in a copper industrial concentrator in Chile, provided the data for the study. Two rougher flotation banks consisting of cells of 130 m3 and 300 m3 were analysed. All the samples from the industrial surveys were analysed by screening and mineralogy, and the mineral recovery along the circuits was evaluated per particle size class, liberation class, type of associations, and others. Additionally, operating data on froth depth profiles complemented the evaluation of the mineral composition of concentrate streams, along the circuit. The results allowed for identifying and quantifying the main factors that affect the copper recovery and concentrate grade along the flotation banks. It was found that minerals with liberation lower than 50 per cent have a significant impact on the recovery. On the other hand, the decrease in the Cu grade in concentrates along the flotation circuits is mainly due to the relative increase of middling minerals (less liberated), non-valuable floatable minerals, such as free pyrite, and gangue entrainment. The characterisation of the gangue entrainment flow rate along the flotation banks showed a strong relationship with froth depth, which becomes more critical towards the last cells of the banks.

Aug 24, 2022

By A. Iordanidis

Mining activities have recently been taken place in Vourinos mountain, northern Greece, exploiting the so-called ?olivinite?. A representative sample was collected from this mining area. Mineralogical analysis was conducted using X-Ray powder Diffraction (XRD). A thin section was prepared and analyzed under optical microscope. X-Ray Fluorescence (XRF) was employed for the chemical analyses of major, mi-nor and trace elements. Environmental Scanning Electron Microscopy coupled with energy dispersive x-ray analysis system (ESEM-EDX) was also applied for the characterization of the sample. Forsterite (Mg-rich olivine) and enstatite (Mg-rich orthopyroxene) were the main mineral phases determined by XRD, with a 56% and 44% content respectively. Trace amounts of chromite spinels were also determined. Based on this characterization, the industrial rock proved to be a hartzburgite (a type of peridotite in petrological terms). Optical microscopy and ESEM-EDX provided similar observations and confirmed the above-mentioned results. XRF revealed a composition of 43.31 MgO, 44.25 SiO2, 9.98 Fe2O3, 1.40 CaO, 0.67 Al2O3, 0.22 MnO, 0.01 TiO2 and negligible amount of LOI (<0.1%). Trace elements with high concentrations were Cr (2678 ppm) and Ni (2044 ppm). The comprehensive characterization of this mining product suggested the suitability for various uses, such as refractories, foundry and slag conditioner. Additional experiments are being carried out for environmental applications, e.g. wastewater treatment.

Jan 1, 2006

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By A E. Waltho, W J. Shaw

Predicting the physical characteristics of various ore types has for long been a difficult problem during mining. Grade control practices tend to concentrate on the chemical grade of the ore. Estimation of physical characteristics such as beneficiation behaviour is commonly limited to the simplistic application of historical averages. Large amounts of geochemical data are often gathered during the exploration and mining stages of a project, especially in ferrous and base metal deposits. In addition to the elements of principal economic interest, samples are often analysed for suites of gangue constituents to determine whether the mineralisation lies within target specifications. This multi-element data is often put to no other use than this simple chemical classification, yet it may present the geologist or metallurgist with valuable insights into the mineral content and physical characteristics of the deposit. Normative mineral estimates have been used as a method for characterising igneous rocks for almost 100 years. The method establishes and applies a set of sequential rules, by which the chemical components of a sample are assigned to mineral components. Provided that it is possible to make some realistic assumptions about the mineral species likely to be present in a rock unit or deposit and their paragenesis, this approach can be extended to a variety of mineral deposits. The geochemical data that are routinely collected when, for example, drilling iron ore and base metal deposits, can be used to derive estimates of normative mineral content. These estimates can be used to characterise physical or metallurgical aspects of the ore, such as density, beneficiation behaviour and metal recovery. This paper examines the application of normative mineral estimates to a variety of practical resource characterisation problems. The potential for predicting the lump and fines proportions of iron and manganese ores is also discussed.

Jan 1, 1999

By D Johns, L Murray

This paper discusses pore pressures in the embankments of tailings dams by comparing real world data with common design assumptions. Assessment of pore pressures has implications on material behaviour interpretation from CPT investigations and, therefore, on the design. For example, the assumption of hydrostatic pressure is conservative for limit equilibrium stability analyses but may be un-conservative in assessing the potential for contractive behaviour and strength loss during shearing. This paper presents some real world data, the investigation methods to determine the pore pressures, and subsequent interpretation of CPT data and material parameters such as the state parameter. It also examines the design implications of assuming a hydrostatic pressure distribution, by comparing results from that assumption with those obtained using the real pore pressures.CITATION:Johns, D and Murray, L, 2018. Characterisation of pore pressure in tailings dams and the implications for design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 239–249 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Y. Belloa, C. Dorfling

The presence of impurities such as Se and Te in copper sulfate leach solutions can have a detrimental effect on electrowinning efficiency. These elements can be removed from the solution by precipitation; sulfurous acid is commonly used as a precipitation reagent, while studies have also reported improved precipitation with the addition of metallic copper. This paper aimed to determine the effect of conditions used during the solution purification step on the characteristics of the precipitates that formed. Precipitation tests were performed in a batch reactor with copper sulfate leach solutions obtained from the base metal refinery of a platinum group metal producer. The effects of agitation rate (250 and 500 rpm), SO2 flow rate (4.4 and 5.8 mL/min.L), temperature (65 and 95°C) and metallic copper powder addition (0, 1 and 2 g/L) on the characteristics of the precipitates formed during the tests were determined using scanning electron microscopy. The major phases detected in the precipitates formed when using SO2 as the only precipitation reagent were elemental Se and Cu2Se. The introduction of copper powder led to the production of different sulfide phases for the experiments conducted at 65°C irrespective of the values of the other reaction parameters. At 95°C, Cu crystals, Cu2O and tiny inclusions of Cu2(Se,Te) were the prominent phases noticed in the precipitates produced from all the tests conducted with copper powder as precipitation enhancing reagent. Keywords: copper, precipitation, selenium, tellurium

Jan 1, 2020

By R. Asamoah, P. Forson, S. Xu, W. Skinner, M. Zanin

In most auriferous hydrothermal deposits, gold is preferentially associated with pyrite and arsenopyrite minerals, with higher economic gold values noted for the latter and arsenian pyrite minerals. In this paper, surface (Cryo-XPS) and solution (EDTA extraction) analysis were used to characterise pyrite and arsenopyrite minerals under different aqueous conditions involving electrokinetic study and collector interactions to better understand ways of improving the separation of pyrite and arsenopyrite. The evidence showed higher surface oxidation at solution pulp pH values in the range of 4-11 for arsenopyrite relative to pyrite. The observed highest ratio of pyrite to arsenopyrite selectivity was 1.7 at collector concentration of 50 g/t and decreased with an increase in collector concentration. Keywords: EDTA extractable iron, selectivity index, differential flotation, grade engineering

Jan 1, 2020

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By M I. Pownceby, S Hapugoda, H Han, E Donskoi, L Lu

Iron ore sinter mineralogy and its associated macro-/micro – structure has a strong impact on sinter quality. At a macroscopic scale, sinter ideally consists of a strong, porous matrix which bonds relict ore nuclei together. Microscopically, the sinter matrix (solidified from the melt part of the initial sinter mix) generally consists of complex calcium ferrites known as SFCA, secondary magnetite and hematite grains (precipitated from the primary sinter melt), glass and silicates. Depending on the conditions under which the sinter structure is formed, two major forms of SFCA with different morphologies are generally recognised, ie fine micro-platy SFCA (usually termed SFCA-I) and coarse columnar/prismatic SFCA. Detailed optical microscope observations of several pot grate and compact sinter samples revealed the presence of a variety of fine, coarse and dense forms of both types of SFCA. The controlled cooling tests revealed that cooling rate has an impact on the form and size of SFCA crystals. In this work, EPMA analysis of SFCA compositions from a variety of pot grate and compact sinter samples are presented. Results show that the SFCA types exhibit a broad range of complex compositions within the system Fe2O3/CaO/SiO2/Al2O3/MgO/TiO2/MnO2. Although SFCA-I and SFCA are known to be crystallographically distinct and with different, well-defined ranges in composition, there was considerable overlap in compositions of the experimental sinter samples. The development of SFCA textures depend on several parameters including the local chemistry and conditions including the maximum temperature attained and the cooling rate, within the sinter bed, thereby suggesting that SFCA identification based on morphology alone may be erroneous.

Nov 8, 2021

By N Guresin, M Rohde

A lead-zinc flotation tailings sample containing silver from BHP Billiton’s Cannington Mine has been characterised to understand occurrences of silver in the tailings by conventional elemental, X-ray diffraction (XRD) and size analyses followed by mineralogical analysis with a scanning electron microscope (SEM) equipped with mineral liberation analysis (MLA) software and the use of an adapted diagnostic leach process originally developed for gold containing materials.The tailings sample contained 67 g/t Ag, 1.8 per cent Pb and 0.52 per cent Zn. The XRD analysis showed that the sample consisted of 74 per cent silicates, nine per cent sulfides, 11 per cent magnetite and small amounts of other minerals such as fluorite, fluorapatite and rutile. The p80 and p50 of the sample were determined to be 106 µm and 38 µm, respectively. The silver distribution was high in the small size fraction with 52.1 per cent of the silver being in the -8 µm fraction. The silver minerals freibergite, acanthite, jamesonite, pyrargyrite and native silver were observed in the mineralogical analysis of the sample by SEM/MLA. The associations of the minerals were intricate and the occurrences of silver were complex. There were finely disseminated silver minerals and also coarser grains of silver minerals in composites with the host minerals. It was estimated that almost 50 per cent of the silver was contained in pyrargyrite, around 14 per cent as native silver and contained in acanthite, 12.5 per cent in galena and around ten per cent in freibergite and jamesonite.These composite particles and the type of the silver minerals present were expected to limit leaching efficiencies of the silver in hydrometallurgical processing. The diagnostic leach tests showed that around 50 per cent of the silver could be recovered by direct cyanidation and higher extractions could be achieved by more aggressive acidic systems.Cyanidation tests were conducted to confirm the findings of the diagnostic leach studies. The investigated cyanidation parameters were time (up to 48 hours), solid to liquid ratio (1:1 and 1:2), cyanide concentration (0.025 M, 0.5 M and 0.1 M) and particle size (p80 of 106 µm, 63 µm and 7.5 µm). The effects of oxygen and lead nitrate were also studied. The tests were conducted at atmospheric temperatures. The maximum silver recovery obtained was about 50 per cent for all the parameter ranges trialled except particle size. The decrease in particle size from 106 µm to 7.5 µm by fine grinding resulted in an increase in silver recoveries from 50 per cent up to approximately 82 per cent indicating that the liberation of the silver grains/minerals is one of the factors affecting the cyanidation recovery of silver in addition to the presence of refractory silver minerals not amenable to cyanidation.Low head grades of silver in the tailings and relatively low cyanidation recoveries of silver (without fine grinding) necessitate a thorough cost analysis for the cyanidation of the Cannington lead and zinc tailings to assess if cyanidation would be a suitable process option for the extraction of silver. It is clear that one of the most important factors in determining the cost feasibility will be the price of silver in the world metal market.CITATION:Rohde, M, Guresin, N and Johnson, N W, 2014. Characterisation of silver minerals in lead-zinc flotation tailings and their response to cyanidation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L. Mabiza

Keywords: Pyrometallurgy, furnace, sulphur, SO2, off-gas, Zimplats Zimplats embarked on an off-gas sampling campaign in December 2009 to characterise the concentration of SO2 in the off-gas from their 13 MW furnace. In excess of forty isokinetic samples (US EPA Method 8) were taken over seven days. The aim of the sampling campaign was to increase the understanding of factors that influence sulphur release from sulphide concentrates in an electric furnace. Specifically, detailed monitoring was conducted over various operating conditions to evaluate: ? The relationship between SO2 and feed rate (i.e. furnace power) ? The relationship between SO2 and ingress (i.e. furnace freeboard pressure) ? The impact of concentrate bed thickness on SO2 (i.e. blacktop) ? The effect of events such as tapping and converter slag return on SO2 ? The desulphurization reactions that take place in the blacktop A model was developed to predict the SO2 content in furnace off-gas for a particular set of operating conditions. In order to evaluate the impact of random, uncorrelated changes in concentrate composition, ingress and power (feed rate) on the SO2 content of the off-gas, a Monte Carlo approach was adopted whereby concentrate composition, power, and ingress were allowed to vary randomly around selected set-points. The model is primarily based on the release of ?labile? sulphur from the partial thermal dissociation of sulphide minerals with an over-stoichiometric sulphur content (e.g., Fe7S8 decomposition to FeS and S). The main findings of this work suggest that labile sulphur does not fully account for the measured SO2 content of the off-gas, and that limited oxidation of sulphides during melting also contributes to the SO2 content. Details of sulphide oxidation reactions in the furnace remain unclear, and it is currently not possible to provide a theoretical framework for the relationship between the extent of oxidation and variables such as temperature, gas composition, particle size, and residence time in the furnace black top. Through the use of the Monte Carlo model it was, however, possible to constrain the extent of sulphide oxidation to about 1%. This work has shown in practice what was expected in concept, that SO2 in off-gas is proportional to furnace power and ingress rate. The model that was developed consistently slightly under-predicts the quantity of SO2 generated. It also highlights that more work is required to better understand the analytical methods used to analyse for SO2 in off-gas.

Jan 1, 2011

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By E R. Ramanaidou, M S. Piggott

Transport to and handling of iron ore at Port Hedland, Western Australia, results in the generation of airborne particulates that contribute to the atmospheric dust load, with concerns about potential local environmental impacts (eg mangrove swamps) and possible human health implications. Mineral and chemical characteristics of the Background soil samples were contaminated with particles of iron ore as martite octahedra and grains of micro-platy hematite as detected by scanning electron microscopy (SEM) in the 2.5 - 10 ¦m and 10 - 50 ¦m size fractions. Fossilized wood fragments similar to those observed in Yandicoogina fines ore were also detected in some background soil samples. With a predicted increase in demand of channel iron deposits (CID) ores and the inherently dusty Marra Mamba ores (eg West Angelas, MAC, OB29/30/35, Marandoo), in conjunction with particulate emissions from hot-briquetted iron and direct reduced iron (HBI/DRI) processing plants, there is the potential for additional sources of anthropogenic dust to contribute to background levels. Mineralogical and chemical characterisation of the entire range of particulates that could be produced is necessary for a complete understanding of their potential impact on the local environment.

Jan 1, 2002