Search Documents

By Raquel Húngaro Costa, Jonathan Tenório Vinhal

The demand for natural resources has grown over the years, however, the environment offers a limited amount of these resources for exploration. Then, the investigation of new methods for recovering and reuse some compounds and elements are essential to know later tailings purposes. Zinc is used in corrosion resistance as a protective coating for several products. One of the steps for the extraction of zinc is by flotation process to obtain the concentrated ore, in which a residue is generated. The aim is to characterize this residue, allowing the choice of recovery routes for compounds and elements in future stages. The methods of analysis were Malvern, VA, Eltra and ICP-OES, besides the water content. In this study, a characterization of elemental chemical analysis was performed, in which the main elements presented were: calcium (17.4%), magnesium (10.3%) and iron (7.97%); the water content was 27% and the grain size of the material presented an average size of 50μm. With the presented characteristics the material can be used, after treatment, in the recovery of other compounds for applications in the sector of fertilizers, ceramics and steel industry.

Oct 3, 2019

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By G. L. Peralta

Geothermal energy is an important source of power in more than 12 countries and is a potential source in 50 countries. However, the exploration and use of geothermal resources generate residues such as scale and sludge. The scale is from the steam distribution pipes while the sludge is from cooling ponds. These solids contain significant levels of elements which are of environmental importance notably, arsenic, sulfur, copper, zinc and lead that require safe treatment and disposal. The compositions, phases, textures, morphologies and size of scale and sludge particles have been studied by laser particle size analysis, light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. In addition, their leachability was tested with protocol leaching procedures and sequential extractions. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how the scale and sludge are formed, their leaching behavior if disposed of in a landfill and in developing appropriate treatment strategies.

Jan 1, 1994

By Denise Cristina de O. Nascimento

Natural lignocellulosic fibers are increasingly being used as polymeric matrix composite reinforcement owing to economical and environmental advantages as renewable and biodegradable materials. Among these, the piassava fiber extracted from a palm tree native of South America stands as one of the most rigid with a potential to be used as composite reinforcement. Therefore, the present work investigates the notch toughness behavior, by Izod impact tests, of epoxy composites reinforced with up to 40 % in volume of continuous and aligned piassava fibers. It was found that the incorporation of piassava fibers results in significant increase in the impact energy of the composite. Scanning electron microscopy analysis showed that the nature of the piassava fiber interface with the epoxy matrix is the major responsible for the superior toughness of the composite.

Jan 1, 2009

By Ailton S. Ferreira, Rubén J. Sanchez Rodriguez, Sergio N. Monteiro, Felipe Perissé D. Lopes, Teresa E. Castillo

"Polyester composites reinforced with natural lignocellulosic fibers have, in recent times, been gaining attention in engineering areas as lighter and cheaper alternatives for traditional composites such as the ""fiberglass"". One of the strongest, the curaua fiber, is today being considered as reinforcement of composites for automobile interior parts. In fact, several research works are currently being dedicated to curaua fiber composites since physical and mechanical properties are required for practical uses. In this work, the thermal behavior of polyester composites reinforced with up to 30 % in volume of curaua fibers was investigated by differential scanning calorimetry, DSC. The results showed endothermic and exothermic events associated with water release and possible molecular chain amorphous transformation. Comparison with similar composites permitted to propose mechanism that explains this DSC thermal behavior.IntroductionThe modem composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace [1]. In fact, fiber composites offer significant advantages over monolitic materials, such as common metallic alloys, plastic and ceramics. One of the most important is the ratio between the ultimate stress and the density, known as the specific strength. For example, in common glass fiber polymer composites, the so called ""fiberglass'', the specific strength of around 400 MPa.cm3/g is higher than any conventional monolitic material. However, drawbacks exist. The energy required to fabricate ""fiberglass"" generates large emissions of C02, which are responsible for global warming. Moreover, ""fiberglass"" is not recyclable and cannot be incinerated [2]. As a result, most synthetic fiber composites end up in landfills or contribute to rivers and oceans pollution."

Jan 1, 2011

By Leonardo Mota, Felipe Perissé Duarte Lopes, Marcelo Gomes da Silva, Sergio Neves Monteiro, Helion Vargas

"Natural fibers, as a class of material, are attracting the interest of engineering sectors owing to specific advantages such as comparatively reduced cost and lower density as well as environmental benefits associated with renewability and biodegradability. For industrial applications, thermal properties, among others, are required. These are major requirements, especially in the case of an insulating natural fiber. In the present work, thermal properties of the curaua were investigated by photothermal techniques, i.e., the open photoacoustic cell and a method based upon the monitoring of the temperature evolution as a function of time. This investigation, in tum, permitted to evaluate two important thermal properties: the thermal diffusivity and the specific heat capacity of the curaua fibers. Indirectly, by means of simple mathematical relations, the thermal conductivity was also obtained. The results were compared with other materials and characterize the curaua fiber as an efficient insulator.IntroductionMaterials are gaining attention in recent years owing to their benefits for the environment as compared to synthetics. Being biodegradable, yearly renewable and recyclable, the natural planted-based are considered fully sustainable [1]. In particular, their life-cycle, from growing to industrial processing, absorbs as much C02 as it is emitted and makes them neutral with respect to greenhouse gases responsible for global warming [2]. Typical examples of these environmentfriendly materials are the lignocellulosic fibers that have been used in simple items such as ropes, baskets, textile, modest roofing, etc, since the beginning of our civilization [3]. In the past few decades, these natural fibers have been extensively investigated [ 4-1 O] as a possible reinforcement phase of polymer composites in substitution for synthetic fibers. In fact, engineering application of lignocellulosic composites are today in the market, especially in the automobile industry [11-13]. Out of the hundreds available natural fibers, only part of them exhibits superior properties to be qualified for composite reinforcement."

Jan 1, 2011

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By Constantino Capurro

For certain applications, coarse titanium nitride (TiN) precipitates can be deleterious for the final properties of the material. Hence, in order to better understand the mechanisms involved in the generation of these precipitates, a thorough characterization of the particles observed in steels with different titanium and nitrogen content was carried out. Samples from liquid steel (tundish), continuous casting billets and final product were evaluated using an Automatic Particle Analyzer (APA) coupled to a Scanning Electronic Microscope (SEM). The location, frequency, size distribution and composition of the different particles observed were assessed. While only few TiN precipitates were observed in liquid steel samples, the density of this type of particle significantly increased in the continuous casting billets samples. Particles ranging from 1 to 10 µm were mainly found in the interdendritic zones of the as-cast structure. The density of TiN particles observed in these samples did not change after re-heating and rolling operations. A model to predict TiN precipitation during solidification was developed. A reasonable agreement was found between model results and measured data. Results of this analysis confirmed that the precipitated fraction of TiN increases as the product of steel Ti and N contents rises.

Oct 30, 2017

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By Donald F. Saunders

Means and relative standard deviations were calculated for eU, eTh, K, and their ratios for aerial gamma-ray spectral data in 29 quadrangles at 1:250,000 scale. Known or suspected uraniferous provinces were characterized by: 1) Higher eU, eTh, and K means (due to generally higher radioelement concentrations); 2) Higher relative standard deviations for eU, eU/eTh, and eU/K (reflecting the presence of local uranium enrichments); and

Jan 12, 1979

By Donald F. Saunders

Means and relative standard deviations were calculated for eU, eTh, K, and their ratios for aerial gamma-ray spectral data in 29 quadrangles at 1:250,000 scale. Known or suspected uraniferous provinces were characterized by: 1) Higher eU, eTh, and K means (due to generally higher radioelement concentrations); 2) Higher relative standard deviations for eU, eU/eTh, and eU/K (reflecting the presence of local uranium enrichments); and lower mean eU/eTh and eU/K values (showing uranium loss from "average" rocks to form local enrichments). "Uranium favorability indexes," i.e., combinations of the sensitive variables, show an excellent qualitative relationship to known occurences and geologic favorability. Results appear to confirm the existence of long-term crustal uranium provinces formed at the time of emplacement of the oldest known rocks.

Jan 1, 1980

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By Jürgen Antrekowitsch, Thomas Griessacher

The recovery of valuable metals from residues like dusts and sludges is nowadays state of the art. Depending on the complex constitution, a recovery of different metals can – in the majority of cases – only be performed with considerable energy input in high temperature processes together with insufficient yields and newly generated residues. Often, the behavior of the dust or sludge in the process during melting or reduction is unknown. In this work, a detailed characterization of selected residues like steel mill filter dusts, cupola furnace dusts and leaching residues is done. The different steps of getting from solid particles into a homogenous liquid phase were investigated. Although high temperature processing leads to high reaction speeds, the complexity of residues keeps the system away from thermodynamic equilibrium. With this research program, some basics are generated to understand smelting and reduction and the gap between thermodynamical calculations and real behavior can be explained.

Jan 1, 2008

By R. Hogg

"The problems of sampling particulate materials, and of characterizing the distributions of particle size and composition are reviewed. Requirements for sampling from comminution systems are discussed and a simple formula is presented for estimating the minimum sample size needed. The limitations and errors associated with the techniques available for particle size analysis are evaluated and guidelines are suggested for the selection of appropriate methods. The use of microscopic and macroscopic approaches to the characterization of particle composition are discussed.INTRODUCTIONComminution is a process of particle size reduction in which the goal is to produce a material with a specified particle size distribution from a coarser feed. In mineral processing applications, the product size distribution is often qf secondary importance to the extent to which individual mineral grams can be liberated from one another. However, due to poor understanding of the nature of the liberation process and the lack of reliable procedures for characterizing it, the actual specification is normally in terms of particle size.Particle size distribution can be regarded as the fundamental characteristic of a particulate system. The distributions of particle shape and composition among the various particle sizes present are often sufficient to define the bulk properties and behavior of the system. Description of the distributions of size; shape and composition of the different phases which may exist within individual particles is necessary to complete the picture and is especially important for predicting liberation etc., in comminution processes. It is quite obvious that · the complete characterization of real particulate systems is a formidable, if not .impossible task. Practical characterization procedures should involve ·evaluation of those characteristics which are deemed to be important and which can be measured. In comminution systems, this should ideally include the particle size distribution, the size-by-size distributions of particle composition, and as much information as can be acquired on the internal composition and structure of individual particles. In most cases, of course, we fall far short of even this rather limited goal."

Jan 1, 1988

By C. J. Beyke

Slags and/or mattes from three secondary lead producers were studied as part of an effort to develop treatment methods for these lead-bearing residues. Each company used a somewhat different production process. Company A used a reverberatory furnace followed by a blast furnace. Company B used only a blast furnace. Company C used both a reverberatory and a blast furnace, and the scrap material was desulfurized with sodium carbonate prior to smelting. The slag matrix produced from sulfur-bearing scrap consisted mainly of iron-calcium silicates; the slag from desulfurized material was similar, but also contained sodium. In all the slags most lead was present in metallic form, often alloyed with tin, antimony, arsenic, and/or iron. Slag from Company B contained the most alloying elements, often as discrete subparticles within the lead droplets. Mattes were produced at Companies A and B; predominant phases were pyrrhotite and magnetite, while lead was present in metallic form and as galena.

Jan 1, 1995

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023

By C. Musingwini, T. C. Sebutsoe

"The primary objective of any mining business unit is to make profit by extracting, processing, and selling minerals from a particular mineral deposit. It is important to optimize extraction of the mineral resource given time, capital, and space constraints. Mineral extraction is often associated with uncertainty due to variable technical and human factors. Technical factors such as grade distribution, ground conditions, and equipment reliability influence the performance of a mining production system (MPS). The performance of the MPS is also impacted by human factors such as employee skills, health, and attendance. Uncertainty associated with technical and human factors often leads to actual output differing from what was planned. Therefore an in-depth analysis of the significant causes of deviations from the planned outcomes is relevant.In this paper we investigate the empirical relationships between inputs and outputs in a MPS in order to assist management in directing efforts at key production drivers. Once a MPS has been empirically characterized, more effort and resources can be focused on the key decision-making variables (DMVs) in order to meet the planned outcomes.For a typical underground, tabular, narrow-reef conventional drill-andblast platinum mine the face advance, face length mined, number of teams, team efficiencies, and team size have a statistically significant relationship with the centares (m²) produced, which is a key performance indicator (KPI). The production function derived in this study can be used to align the physical, technical, and human factors together to predict the optimal output level. The most significant production lever of the MPS is the face advance. IntroductionA mining production system (MPS) is a result of an iterative process of design, planning, and optimization of mining input variables and decision-making variables (DMVs). The MPS exists within the mineral extraction link of the complete mining value chain. It represents the stage where mining companies have the opportunity, through production, to start generating returns on the investments undertaken. Returns on shareholders’ investments can be realized at this stage."

Jan 1, 2017

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014