Search Documents

Samples of the feed, underflow and overflow mediums from dense medium cyclones operating at low separation densities in eight commercial coal washeries were sized and analysed, to obtain comparative cyclone classification performance curves for the magnetite, shale and coal components in the circulating medium. The resulting component classification curves indicated that the dense medium cyclones hydraulically classify the magnetite and the shale to the underflow with a Stokesian size and density relationship at these low medium densities, ie the shale curve was shifted parallel to and appropriately coarser than the magnetite curve because of the lower density of the shale. However the lower density coal reverse classified to the overflow (ie away from the cyclone wall) with a similar Stokesian relationship. By correcting the magnetite and shale classification curves for the bypass inefficiency to underflow, and similarly correcting the coal classification curves for the bypass inefficiency to overflow, the corrected classification curves for the magnetite, shale and coal were reasonably parallel (considering that the coal has a range of densities). Using a value of five for the density of the magnetite, the displacement of the shale and coal curves corresponded to densities of 2.27 and 1.38 respectively for one circuit, although the data was not as good for the other circuits. This reverse classification mechanism was confirmed in a 140 mm diameter laboratory dense medium cyclone circuit using low density (1.20 - 1.30 RD) tracers, sized from 0.25 to 2 mm. These classification performance curves were corrected for bypass ineffiency (as above). The corrected curves were parallel and displaced according to tracer density, even though the lowest density tracers were reverse classified to the overflow. The data indicate that the rates of classification of all particles could be described by the same Stokesian relationship, regardless of the direction of travel, except for a narrow band at the partition density. Particles heavier than the partition density classified to the underflow, particles lighter than the partition density reverse classified to the overflow and particles identical to the partition density were not classified at all. Consequently it should be possible to simulate partition in dense medium cyclones, operating under free settling low density conditions, with a simple cyclone classification model, provided the partition density can be accurately calculated from, or correlated with the cyclone feed, underflow or overflow pulp densities. The tracer partition performance in the laboratory cyclone was an inverse function of the tracer particle size, as proposed by King and Juckes (1984) for medium/coal ratio in low density medium systems. Their sized coal data was parallel, with lower partition values due to a higher energy cyclone. Partition data with similarly sized tracers (Scott, 1988) showed a parallel shift to higher partition values due to the separate effects of higher viscosity medium and a larger diameter lower energy Cyclone.

Jan 1, 1993

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous metals of certain classes recovered in the United States for the year 1924 to 1925 as shown in Table 1. The figures are tabulated simply to give the reader some idea of the scope of the secondary non-ferrous metal industry. Approximately 900,000 tons of an annual value of $244,000,000 were recovered in the year cited. In 1916 (again using the Mineral Resources of the United States as authority) the tonnage reclaimed was approximately 632,000 tons and the value, because of the high prices for metals prevailing at that time, amounted to $265,000,000. It is not the purpose of this paper to discuss smelting and refining operations or the feasibility of an organization, primarily engaged in some other activity, conducting smelting and refining operations to convert its own non-ferrous scrap metals and alloys. The classification and preparation of these non-ferrous materials is a preliminary step, regardless of what subsequent operations the material may pass through or where these operations may be conducted. For that reason the subject can be readily discussed without any reference to subsequent activities. Space must be provided, with suitable handling facilities, scales and the necessary storage bins where the material may be accumulated. The scope of the activity, the nature of the industry and the tonnage handled will determine, in a large measure, what preparation, if any, it may be desirable to give these scrap materials to put them in the best marketable condition. By preparation is meant largely what, for the want of a

Jan 1, 1928

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some Secondary Non-ferrous Metals Recovered in the United States for the Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 $ 71,170,400 Brass, scrap remelted 242,300 56,270,800 Lead as metal 112,4201 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc -in alloys other than brass 13,300 Tin as metal 1 7,950 35,165,400 Tin in alloys 23,000 Antimony as metal 1 } 3;794,000 Antimony in alloys 10,839 Aluminum as metal 17,700 24 Aluminum in alloys 26,300 ,816,000 Nickel as metal 19 1 1,518,000 Nickel in non-ferrous alloys 2,109 Total 882,600 $243,570,700

Jan 1, 1928

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form .of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition-of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some. Secondary Non-ferrous Metals Recovered in the United States for the -Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 8 71,170,400 Brass, scrap remelted : 242,300 56,270,800 Lead as metal : 112,420 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc in alloys other than brass 13,300 Tin as metal 7,950 Tin in alloys 23,000, 35,165,400 Antimony as metal 1 3,794,000 Antimony in alloys : 10,839 Aluminum as metal 17,700 24,816,000 Aluminum in alloys 26,300 Nickel as metal 191 1,518,000 Nickel in non-ferrous alloys 2,109 Total l 882,600 $243,570,700

Jan 1, 1928

Studying the ore textures in a discrete orebody is a novel approach to estimating liberation potential of the ore minerals present. As part of a PhD thesis, this project aims at classifying and quantifying the textures of the Hilton North orebodies, and at estimating their liberation characteristics.

Jan 1, 1993

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By M. J. Taylor

A common method of classifying non-water- impounding mine waste structures is necessary to facilitate professional comnunications within the industry and between representatives of industry and government. Camnon classifications can a1 so he1 p quickly create and maintain a mental picture of the structures being discussed. Three categories for classification presented in this paper include: (1) configuration and location with respect to existing topography. (2) material characteristics of waste, and (3) environmental sensitivity or characteristic; of the disposal area. Configuration and location classification involve terminologies typically utilized for waste dumps over the past several years. General classification categories for non-impounding structures include: (a) valley-fill, (b) cross-valley, (c) side-hill, (d) ridge, and (e) heaped. Material characteristics can govern the location, engineering details, and environmental sensitivity of the waste structure. Material classification includes: (a) hazardous, (b) non-hazardous, (c) inert, (d) fugitive dust susceptible and (e) leachate susceptible. A1 though many characteristics are potentially applicable, this paper will focus on the categories mentioned above. Environmental sensitivity of a waste structure encompasses many objective and subjective evaluations plus many multi-disciplinary considerations. Environmental sensitivity incorporates numerous factors in addition to those highlighted in configuration and location, and material characteristic classifications. A few examples of how this categorization can govern the engineering design and location of waste dumps are provided in this paper. In addition to the verbal descriptions of classifications, a simplified version of the combined classifications with an alphanumeric format and its methodology is discussed in this paper. Surface water controls often govern the classification or vice versa. In order to maintain a non- impounding status, water must be prevented from collecting behind the structures. Depending on material characteristics, water inflow to or over the site can cause significant environmental or human consequences. Finally, the access of water to the waste dumps can play a large role in the degree of environmental sensitivity to the site. This paper provides a framework in which to discuss the other aspects of this conference and also provides insights as to how the framework is based on actual practice.

Jan 1, 1985

By W. G. Hatch

Introduction Classified equipment originally installed in 1923 in the Britannia mill consisted of eighteen Model C Dorr Simplex classifiers, each in closed circuit with a pebble-mill. These machines were only three feet wide and of light construction, so that their raking capacities were necessarily limited, the maximum being about 20 tons per hour for each classifier. On conversion from pebble-mills to ball-mills, in 1924, attempts to increase circulating loads with higher rake speeds resulted only in overflowing a coarser product to the flotation cells. The elevator type of classifier was developed locally in 1935 and during that year two units, each having a sand carrying capacity of from 30 to 40 tons per hour, were installed. With such loads, a material increase in the grinding capacities of the ball-mills was noticed, and, after further development work on the elevator classifier, fifteen of the small Dorr classifiers were replaced by units of this type, capable of handling approximately 75 tons of sand per hour, with later alterations increasing this capacity to well over 100 tons per hour. In the meantime, the three remaining ball-mills had been placed in circuit with Dorr FX classifiers, one of which was six feet wide and the others five feet wide. Impartial and exhaustive tests conducted on the Dorr FX versus the elevator classifier showed the average results on these machines at Britannia to be substantially the same. A large amount of testing was carried on to determine the effect of circulating load on the output of the grinding units. This work indicated a rapid increase in the grinding rate as the ball-mill feed increased up to about 60 tons per hour, after which a relatively slow increase took place up to 100 tons per hour. No benefits were derived from higher circulating loads. A 300 to 500 per cent circulating load, depending on the nature of the ore treated, is considered to be within the economical range for the grinding of Britannia ores.

Jan 1, 1946

By G. J. Knighton

Introduction The Sullivan concentrator treats the complex lead-zinc-iron ore from the Sullivan mine of the Consolidated Mining and Smelting Company of Canada, Limited, to make a lead and a zinc concentrate for its metallurgical plants at Trail. Three miles separate the mine and mill, which are situated near the town of Kimberley, in the East Kootenay district of British Columbia. The orebody consists typically of banded sulphides, mainly galena, sphalerite, pyrrhotite, and pyrite. Important factors in the concentration of the ore are its exceedingly complex and its high specific gravity. It should be remembered throughout the paper that results and figures are based on Consolidated's experience with the Sullivan ore. The present mill feed rate is 8,500 dry tons of ore per 24 hours, for an operating week of five and a half days. Grinding and classification of the ore are carried out in three stages and, in addition, there is a re-grind section which re-treats the zinc middling. It is the purpose of this paper to discuss the classification in the various stages and to give the results o comparative tests which have been carried out for the purpose of improving operations in the mill. The Primary stage consists of six units, each made up of a ball-mill and classifier (see accompanying flow-sheet). Four units operate in open circuit and two in closed circuit. The secondary stage consists of eight ball-mills operating in closed circuit with twenty-one classifiers. In the Tertiary stage are two ball-mills in closed circuit with eight classifiers. The re-treatment section for re-grinding the zinc middling comprises one ball-mill in closed circuit with two classifiers.

Jan 1, 1947

The concept of classification in wet, closed circuit ball milling is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters that effect fines removal are identified and discussed, and a quantitative index for circuit classification effectiveness is presented.

Jan 1, 1987

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By Donald A. Dahlstrom, Wai-Ping Kam

The mineral industry and individual processing plants are large consumers of energy. While energy conservation has received some attention in the present Federal Administration National Energy Strategy proposal it is obvious that the mineral industry should also continue to emphasize energy consumption reduction for important economic savings alone. As indicated by other studies, comminution is the largest single consumer of energy in the mineral processing plant (1.3% of total electrical energy consumption in the U.S.A.).1 Fine grinding is the largest portion of this amazing statistic. While substantial energy savings have been demonstrated by new machine developments and improved control methods, undoubtedly there are additional areas in comminution where substantial progress can be made. Some time ago, the U.S. Department of Energy published a report on "Comminution and Energy Consumption" by a committee composed of experts in the field of comminution from industry and academia. They identified the following potential for energy savings by specific areas? Classification device design 9-13% Comminution device design 3-16% Control 9% Grinding additive 3-6% Materials 3% It is apparent that the classification device had the first or second highest savings potential. Obviously, serious research consideration must be given to this technology area. A series of three papers have previously been written on the subject of two stage classification research work for ball mill operation by the authors. Accordingly, a brief review will be made. Previous Research Results on Two Stage Classification The hydrocyclone was selected as the type of classification equipment for this study as it represents by far the majority of the devices used in ball milling. While four different hydrocyclone circuits have been proposed by others,3 only two were considered in this work as illustrated in Figure 1. Flowsheet A is truly counter-current in nature in that the product from the ball milling circuit is taken from the first stage overflow

Jan 1, 1992

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By F. S. McNicholas

Various methods of block caving and draw practice are classified and the advantages, disadvantages, rock, treatment, size of orebody, costs, and profit comparisons, and other factors which determine the selection of the proper method are outlined.

Jan 1, 1951

By Srinivasulu Tadisetty

The productivity and safety of Indian longwall operations are insignificant because of complex geomechanical conditions. Therefore, the continuous monitoring and forecasting of abnormalities is imperative. Authors developed an innovative real time system and implemented in one of the Indian longwall mines. The real time system was successfully acquired data from underground chock shields and classified the behaviour in real time as per the standard norms. Furthermore, it forecasted the abnormal behaviour of chock shields promptly. The management was implemented appropriate precautionary measures based on real time forecast. Subsequently, the longwall operations were successfully completed with enhanced productivity and safety. This paper discuss the impact of the innovative system on productivity of experimental longwall mine.

Jan 1, 2006

THE object of all classification is to group together things which are alike, and separate those which are unlike. This object is essentially a practical one, enabling us to apply past experience to new conditions: Many costly large-scale experiments lose half their importance for want of proper description of the coal used, and the consequent impossibility of predicting other coals will behave in the same way. I do not, therefore, make a fundamental distinction between "scientific" and "use" classifications, except in so far as use depends on conditions, such as size or impurities which are not related to the nature of the coal substance itself. The characters chosen to define the classes of coal must be such as are accompanied by as many other properties as possible. It is not to be expected that any system of classification will enable us to predict every property of coal, since all specimens have an individuality of their own. But specimens can be grouped by a number of resemblances into species. Further, species which resemble each other can be grouped into genera.

Jan 1, 1928

By Persifor Frazer

(Read at the Wilkes-Barre Meeting, May, 1877.) A CLASSIFICATION of natural objects is usually based either upon some fundamental and permanent attribute of the thing itself (as in the case of scientific classifications), or it embraces one or more generalizations convenient for use in ordinary life. Thus, it suffices for the statistician to, know that so many tons of fish are annually taken by our fishermen, and that they realize so many thousands of dollars, whereas to the student of natural history the anatomy, habits, and relationships of the animals are of chief interest, as settling their respective places in the scale of animate nature. Many different classifications of coals have been attempted, as one would naturally anticipate from the immense extent of the coal trade, and the different localities whence the supply was derived. The English divisions were prevalent up to the date of the publication of the last geological survey of the State, except so far as they were modified by local designations. Indeed, Rogers' classifications made very little alteration in the English nomenclature, as may be seen by comparing. the tables given below. To commence with the different kinds mentioned in Ure's Dictionary of Arts, Manufactures and Mines of 1845 " 1. Cubical Coal.-Black, shining, compact, moderately hard and easily frangible. Comes out in rectangular masses, of which the

Jan 1, 1878

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934