Search Documents

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Orville R. Lyons

THE Russellton preparation plant of Republic Steel Corp., located north of Pittsburgh, Pa., prepares 3 1/2x0-in. Thick-Freeport coal by means of a 13-ft 6-in. diam Chance cone and 16 No. 7 Deister tables. The plant feed ranges between 370 and 410 tons per hr, of which approximately 31 pct is ¼x0-in. size, and the plant reject ranges between 14 and 16 pct of the feed. The 3½xY4-in. washed coal, the cone product, is dewatered and desanded by a double-deck Parrish-type shaking screen 46 ft long and 7 ft wide. The 1¼x¼-in. portion is further dewatered by two 4x12-ft single-deck vibrating screens. The ¼x0-in. washed coal from the tables is distributed to three 54x70 in. Bird centrifuges. The dewatered centrifuge product is combined with the product of the de-watering screens prior to loading into railroad cars. During the early part of 1951 complaints were received from officials at Republic's coke ovens concerning the moisture content of Russellton washed coal. The records revealed that during the first half of 1951 the shipped washed coal moisture averaged

Jan 1, 1954

By F. G. Miller

The washabilities of typical bituminous coals are discussed in an effort to illustrate the importance of determining, by a complete washability study, the sulfur forms and their distribution in a coal. This study will then show the extent to which the sulfur can be removed. It should be emphasized that each potential application requires a thorough study because of the varying amounts of sulfur in different coals. It is not the intent of this paper to show the best results that flotation can produce, but rather to illustrate the potential of this process and point out the importance of improved flotation techniques where sulfur reduction is involved. It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur make up almost all of the total sulfur content, occur in varying amounts in different coals, and can vary greatly in coal of the same seam. Pyritic sulfurs of 20% to 80% of the total sulfur have been reported. Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and ones' state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing

Jan 1, 1964

By A. C. Fieldner, W. A. Selvig

Ash in coal has always becri regarded as an undesirable substance, as the heat content of a coal dccreases in direct proportion to its ash contcnt. It represents so much inert materid that has to be transported, handled when the coal is burned, and finally disposed of. W. R. Roberts, in an address bcfore the Engineers' Society of Western Pennsylvania, Pittsburgh, on Sept. 29, 1925, said that on an annual output of five hundred rnillion tons of coal, a reduction of 3 per cent. of ash means fifteen million tons of refusc and a decrcase of $30,000,000 in freight charges. Ash also often prevents effieient utilization of the coal through the formation of clinker causcd by the mcltirig of the ash constituents when subjected to heat. The mineral constituents of coal may be of such nature as to make the coal unsuited for speeifie uses as for instance, high-sulfur coal for making metallurgical coke. While the usual proximate analysis of coal gives the amount of ash, it gives no information as to the nature and coniposition of the ash nor of the minera1 constituents from which the ash is produced. For the efficient washing of coal to remove ash-forining constituents it is desirable to know the composition and distribution of the ash-fonning constituents. Obviously such information is also desirable for the most efficient utilization of coal. Nature and Composition of Coal Ash Coal ash may be defined as the inorganic residue remailning after cornplete ignitior of coal. It is dcrived from the mineral constituents of thc coal. The ash-forming constituents may be roughly classified as inherent impurities and extraneous impurities. The former are mixed intimately with the coal substance, and arc derived either from the original coal-forming material or from external sources such as sedimentation and preeipitation while the vegetal coal-forming plant remains accumulated. The latter are present in the coal bed as partings, bands or nodules of pyrite! slate, shale, calcit,e, bone, etc. These are formed either during the laying down of the coal bed, or subsequently. Flag-

Jan 1, 1927

By S. W. Parr

The extent to which geological carbonization has taken place in the process of coal formation is a fundamental factor in all considerations relating to classification, oxidation, deterioration, spontaneous combus tion, and especially in all considerations relating to destructive distillation having as an objective the production of marketable coke and by-products. Moreovcr, it may be readily shown that a striking relationship exists between the geological decomposition or geological carbonization processes and those artificially produced by heat. This may be well illustrated by bringing again to view some of the charts more commonly mct with 25 years ago, as in Fig. 1.' In this figurc the line of geological decomposition by decay, pressure, etc., because of its relation to the line of carbonization by destructive distillation, becomes of special significance when we attempt to formulate any system of classification which shall be reasonably scientific and at

Jan 1, 1927

By R. Q. Shotts

This paper is a review of recoverable reserves of bituminous coal in the Southern Appalachian area, according to the latest published estimates. A few comparisons are made, some apparent trends are discussed, and some comments are made regarding the limitations of present estimates. The definition of Southern Appalachian area used in this report is somewhat arbitrary. It includes all the bituminous coal deposits of Alabama, Georgia, and Tennessee. All of West Virginia has been excluded. The East Kentucky and Virginia counties included were selected in connection with a literature study the writer made in 1959 of possible coal supply areas for the Tennessee Valley Authority. The selected counties were considered to be the only ones from which TVA might expect to obtain coal. The availability of coal from some of these counties is doubtful, but no other East Kentucky counties were considered more than remote possibilities. With these limitations, the Appalachian area covered is that from which producers of electric power and steel and commercial coal users, located in the Southeastern U. S., may expect to obtain their supplies of coal. Of course, it is recognized that coal from the eastern interior fields is also available to many of these same organizations. RANK AND QUALITY OF THE COALS Practically all the coals in the Southern Appalachian region are of high volatile A bituminous rank. An occasional sample indicates a slightly lower rank, but such samples may be oxidized or otherwise not representative. Some thin beds in Lookout Mountain and Sand Mountain in Alabama and Georgia, are low volatile bituminous coals, but they have not been mined extensively in modern times. There is a possibility that some of the deeper beds along the southeastern edge of the Warrior field of Alabama are near the Low-medium volatile bituminous dividing line. The Sewanee bed and some other minor ones of the Southern Tennessee field, some of the lower beds in Virginia, many beds in Sand and Lookout Mountains in Georgia and Alabama, one or more beds in the Coosa field, possibly some lower beds in the Cahaba field, and most of the beds along the southeastern edge of the Warrior field and the southern end of the Sequatchie anticline of Alabama, are of medium volatile bituminous rank. The quality of the Southern Appalachian coals is highly variable. Some of them, particularly such prevailingly thin ones as the Black Creek bed of Alabama and the Straight Creek bed of Kentucky, are unusually low in mineral matter— probably the lowest in the U. S. With the exception of certain beds and local areas, Alabama and East Kentucky coals probably have as low average ash and sulfur content as can be found in any sizeable coal area in the country. The sulfur content of Southern Appalachian coals is also variable, but few beds are consistently high in sulfur. In Alabama, sulfur generally increases from southeast to northwest across the Warrior field, but this trend is not quite as clear in the other states. A few beds in Northern Tennessee are prevailingly high in sulfur. All Southern Appalachian coals are potential coking coals if they can be prepared to meet chemical requirements. Only a comparatively small part of the medium volatile A bituminous coal, but most of the medium volatile bituminous coal mined is actually used for coking purposes. An estimate of reserves of coking coal under the requirements of present practice, could be compiled comparatively easily, but this probably has never been done. The reserve of coal that can be coked as an ingredient of a suitable blend is probably many times the size of the reserves of coal that will yield suitable blast furnace and foundary coke without blending. WHAT CONSTITUTES ECONOMICALLY RECOVERABLE COAL RESERVES? When one first realizes the vast extent of the coal-bearing rocks in the Southern Appalachian area, (see Fig. 1) the thought is likely to occur that the supply of coal is inexhaustible. This is particularly true on realizing that in some of the basins of thicker coal-

Jan 1, 1962

By A. E. Zawadzki

A progress report is presented on the development of a process for the removal of sulfur dioxide from flue gases. Catalytic oxidation of the sulfur dioxide in flue gases, with the production of recoverable sulfuric acid, has been demonstrated to be technically feasible. Problems associated with the process are discussed. The need for an inexpensive and efficient process for controlling sulfur dioxide emissions from utility plant stacks has been accentuated by the ever-increasing public demand for elimination of all man-made air pollutants. I would like to describe the results of an investigation of the development of such a process; more important, I would like to present a discussion of the problems associated with the process which remain to be solved. The research work on the BCR catalytic gas phase oxidation process has been jointly sponsored by the Association of Edison Illuminating Cos., Edison Electric Inst. and Bituminous Coal Research, Inc., since 1958. However, work on SO2-pollution abatement was initiated by BCR in 1953. Tieman and Clymer,1 working with ozone and simulated flue gases, evaluated a gas phase oxidation process for removing SO2 from flue gases. Their experimental data indicated that the use of ozone to oxidize SO2 in flue gas concentrations, with subsequent recovery of H2SO4, did not appear to be economical due to the large ratio of ozone to sulfuric acid produced (2.6 to 1). The cost of the ozone would be 6 to 10 times the cost of sulfuric acid produced. As a result of the ozone study, work on a catalytic oxidation process was developed. The following reactions are the basis for the catalytic oxidation process Reaction [I] normally occurs in the combustion of sulfur-bearing fuels. At the high temperature found in the combustion chamber, 95% to 99% of the sulfur in the fuel is oxidized to SO2 and 1% to 5% is oxidized to SO3. The concentration of SO2 in the combustion gases depends on the combustion efficiency and the quantity of excess air used. A commonly used rule of thumb is 0.1 percent by volume SO2 in the flue gas for each 1% sulfur in the fuel. Reaction [2] proceeds at a wide range of temperatures. The rate of the reaction is rapid above l,000°F; however, the equilibrium conversion drops rapidly above this temperature. 2 Reaction [3] occurs rapidly to completion at temperatures below 400°F; above this temperature some SO3 exists in equilibrium with H2SO4. Complete dissociation of H2SO4 occurs above 650°F.3 The simplicity of the proposed process provided added incentive to the development and evaluation of the various component unit operations. The advantages of the process were considered to be as follows: 1) no raw materials were required, 2) the unit operations were not radically new; and 3) a salable product, sulfuric acid, would be produced. The successful development of the process was contingent upon the solution of several major problems: 1) The development of a catalyst which would provide high catalytic activity at reasonable conditions of gas flow and temperature without causing an unacceptable increase in pressure drop. 2) The development of a high temperature dust collection system to provide clean flue gases to the catalytic reactor. 3) The complete recovery of the sulfuric acid produced in the process; the effluent gas must contain less than 20 ppm by volume of sulfuric acid. As of this date, the complete solution to these problems has not been achieved. EXPERIMENTAL Catalyst Development: The use of platinum and vanadium catalysts for the production of sulfuric acid by the treatment of dry gases containing 5% to 20% by volume sulfur dioxide has been known for many years. The application of the basic idea of catalytic oxidation of sulfur dioxide in flue gas concentrations was

Jan 1, 1965

During the past year the Committee on Coal and Coke has been collecting data concerning various phases of the bituminous industry about which considerable misinformation has been circulated even, in some cases, through the coal trade papers. The data here presented have been compiled by various members, from the most authentic sources available and, where possible, cover the period 1913-1924. They will enable comparisons to be made within the industry, and of this and other industries, and will explain some of the differences between conditions existing now and in the prewar period. Capacity and Over-development The capacity of bituminous mines is frequently stated at figures ranging between 800,000,000 to 1,400,000,000 tons per year. Table 1 shows statistics for the industry, mainly from U. S. Geological Survey sources but partly from U. S. Coal Commission reports. Column 3 gives the mine capacity with equipment and labor as of given date, as estimated from the data published by the U. S. Geological Survey. This is calculated for each State by obtaining the total man days worked as reported by the operators (multiplying average men employed by total days worked at each mine) and dividing this figure into the total production, getting the production per man day; this figure times number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method—one that the total number of men employed is used, instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. The first objection is answered by the fact that the same number of men is used in estimating capacity as is used in actual production, and while this number is always from 12 to 20 per cent. more than are actually working, this condition exists at all times, although it is worse at times of maximum output. Few coal men will agree with the conclusion that the use of 308 days is correct, as it is practically impossible to keep any mine working full time at the same daily rate of production as when it is working part time, and the opinion is

Jan 1, 1927

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By T. Reed Scollon

Coal reserves of the Rocky Mountain area are vast and are more than adequate to meet significantly increasing demands in the immediate future. Practically all of the increase in coal demand for the next decade or so will be in the electric power utility sector. All ranks of coal are available in the area, and from a technological viewpoint, all are suitable for electric power generation. Location of economically recoverable coal deposits, location of generating plants with respect to power demand areas and sources of cooling water, and availability and price of other fuels are the major factors which, individually or in combination, will determine the ultimate selection of Western coal deposits to be developed for electric power generation. The low sulfur content of most western coals and the non-urban location of many power plants should tend to minimize problems of air pollution. If projections for nuclear power prove correct, increases in demand for Rocky Mountain area coals beyond about 1980 will depend primarily on the extent of commercial development of synthetic fuel processes. Current research activities on the conversion of coal to liquid and gaseous fuels are promising. Most western coals range in rank from lignite through high-volatile bituminous coals and are particularly amenable to conversion. Vast reserves of Rocky Mountain coals have long lain dormant primarily because of their remoteness from major market areas. Recently, however, innovations in coal transportation and electric power transmission methods, combined with unprecedented demands for electric power in the West, have resulted in large-scale development of some of these coals. In the past few years, announcements of coal mine openings and transportation plans in the Southwest have been filled with superlatives: The Navajo mine in northwest New Mexico is expected to be the largest mine in the country in the near future. The largest single coal agreement ever made provides for coal shipment from northeast Arizona to Nevada via the largest and longest coal-slurry pipeline ever used. An 1100-mile haul of coking coal from northern New Mexico to California by unit train began last year. It is the purpose of this report to evaluate the coal resources of the Rocky Mountain area, and to project their potential utilization. In projecting energy demand levels on a national basis, the Bureau of Mines has developed some rather complex techniques to cope with uncertainties. Using these same techniques, an estimate has been made of consumption of Mountain area coal in 1980. No attempt was made to estimate coal consumption beyond 1980, but new market potentials are discussed briefly. The present and potential coal-producing fields of the Rocky Mountain area are in six states comprising the Mountain Region - Arizona, Colorado, Montana, New Mexico, Utah, and Wyoming. Since approximately 19% of the coal produced in these fields is shipped to the Pacific Region (Washington, Oregon, Cali-

Jan 1, 1969

By W. J. Schuster

Safety in coal mines depends largely upon adequate training of the foreman. Although management must provide modern and safe equipment and at all times keep mines in first class condition from a safety viewpoint, final results will be determined by the quality of supervision. HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large underground mines in eastern Ohio. The section of Pittsburgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it. Haulage System The Pittsburgh No. 8 seam in eastern Ohio is relatively level, with only minor local dips. Throughout the Hanna Coal Co. mines, entries are generally 12 ft wide. Rooms are driven on a 60" angle on 30-ft centers and are 22 ft wide. No attempt is made to extract the 8-ft pillars between. The entire length of main line haulage is gunited in one mine, and a major portion in another. Two of the mines have single-track main haulage roads with passways. The third, a new mine, is double-tracked, and the roof is supported by steel crossbars, 60 lb or heavier, spaced on 4-ft centers and lagged. In recent years timbering on main line and secondary haulage roads has been accomplished by one of two methods: 1—crossbars are supported on a small section of post set in a hitch hole in the rib, or 2—or a hole is drilled in the rib about 12 in. below the roof, of sufficient depth to fasten securely a short length of 40-lb rail, the bottom of the rail facing the roof, on which a short post is set directly under the crossbar. At present the hitch-hole timbering method is favored. At two of the mines the main line haulage locomotives are 26-ton, 8-wheel units. These locomotives are of the axleless type, each wheel being individually mounted on the frame. The motorman's compartment is encircled by 3-in. armor plate for the protection of the occupants. At the third underground mine conventional 15-ton locomotives are being used. However, these locomotives have been completely rebuilt in the company's shops. Equipment has been streamlined and quarters have been provided for two people, who are protected by heavy steel plate in much the same way described above. This modernization program has been completed on all secondary haulage locomotives at the three mines, and the company is well on the way to similar equipment of the 6-ton section locomotives. The following additional features have been included in their modernization: 1—additional support for the motors to prevent their falling to the middle of the track and derailing the locomotives should a break occur in the suspension bar support; 2—installation of additional bracing to prevent brake rigging from becoming displaced and causing derailments; 3—enclosure of all electric wiring in conduit or raceway; 4—provision of an enclosed compartment for the storage of re-railers, jacks, and other equipment, so that they need not be carried on the outside of the motor; and 5—redesign of the end of the locomotive opposite the operator's compartment to prevent anyone's mounting from that direction. It is interesting to note that some

Jan 1, 1955

By A. L. Bailey, B. A. Landry

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally. Of course, the matter is rendered complex by the circumstance that the float-and-sink test, not a simple analytical measurement but a process test, comprehends a number of more-or-less independent items of fundamental data; and as shown in the report, the' variability of the samples differs with respect to these different items. This condition and the wide variety of situations in which float-and-sink test data are used, in combination with other factors, to study complex process operations, indicate the difficulty of setting up fixed standards for float-and-sink sampling and testing. At this stage at least, it is the intent rather to obtain experimental data on the principal Factors involved so that the reader may arrive more intelligently at a procedure adapted to his problem. The authors of this paper have presented experimental data showing the relationship between size of sample and particle size for different variability tolerances with respect to percentage of sink. In further studies, data are being collected to appraise also the variability of the samples with respect to float-ash content and size consist. The scope of this work will be broadened to cover particle sizes up to 4 in., and a third series of tests has yielded similar data for a much cleaner type of raw coal. Thus, the further studies will make available a fairly comprehensive meas- ure of variability with respect to size consist, percentage of sink, percentage of middlings, and percentage of ash in the float, for three coals ranging from 3.87 to 17.68 pct in refuse content (heavy sink material) and from 4.18 to 17.52 pct in middlings. Introduction At present there are no published standards for float-and-sink test sampling. During the rapid expansion of float-and-sink test work, varying procedures have been based on adaptations of the ASTM standards for sampling coal for analyses. For this reason, a special study of gross sample reduction has been undertaken to determine the limits for this step in the operation where no reduction in particle size is to be made before testing. Float-and-sink tests are made whenever a thorough study of coal characteristics is desired. The tests may be made on samples from coal-cleaning units such as jigs or tables, or coal samples may be tested which are taken from a loading boom, railroad car, or the coal seam itself. The resultant gross sample may be large and pose a problem of sample reduction. The question is, then, how much can the sample be reduced and still fall within preassigned limits of accuracy of the original gross sample of coal? Coal from channel samples may be crushed to liberate impurities and then separated into various gravity fractions from which washability curves are drawn; from these curves, it is possible to determine the cleaning characteristics of the coal. However, coal samples from coal-cleaning units cannot be

Jan 1, 1950

By A. L. Bailey, B. A. Landry

W. W. ANDERSON and G. E. KELLER*—We want to compliment the authors on this very thorough paper. It gives information which the coal industry has needed for some time. We hope that the additional information which the authors are collecting will he available shortly. The mixing and riffling procedure that was followed for experimental purposes is obviously not practical in routine float-and-sink testing because of the particle size degradation which would result in handling the sample so many times. It is important to obtain our tloat-and-sink fractions with a minimum amount of handling of material. A statement is made in the paper (p. 80) that "the variable most likely to affect the size of sample required to meet a given preassigned accuracy would be the state or degree of mixing of the coal." We agree that this is a large factor, but do not believe it is the most important factor. Our own opinion is that the most important single factor governing the total gross weight of sample that must be collected is the percentage of the weight of material in the smallest fraction that results from the screening and float-and-\ink operations. In other words, size of sample is governed by the total number of fractionations that must he made, and the distribution of material within the fractions. We can imagine a coal with perfect mixing, but with such a small amount of material in some float-and-sink fraction in one of the coarse sizes that a much larger sample would have to be taken than would be the case with very poorly mixed material, but with a large percentage of coarse material more evenly distributed in all float-and-sink fractions. Our own observation of many float-and-sink tests that we have run in our own organization on many types of coal is that the size of sample that must be used on fine size float and sink is governed more by the requirements for weight of material to be used for analysis in the laboratory than by weight of material necessary to obtain accurate float and sink percentage of weight values. In other words, it is our opinion that very small samples can be used for float-and-sink fractionation in the fine sizes, but that accurate analysis of the fractions will depend on a larger weight of sample being pulverized for the laboratory than is necessary to establish the float-and-sink distribution with respect to weight. A. L. BAILEY and B. A. LANDRY (authors' reply)—The authors thank Messrs. Anderson and Keller for their comments based on long experience. It is agreed that the involved mixing and riming technique used may be disadvantageous from the standpoint of degradation. Fortunately, the paper does point out that the extended riming was unrewarding in causing further mixing. Two large unknowns remain, however: (1) how much of the mixing from the presumed highly unmixed state in the bed was achieved toward the random state during blasting, loading, transportation, screening, and further transportation to the point where the gross sample was taken, and (2) how much of the mixing took place during the preparation described preceding riming. As has been pointed out by one of the authors.6 the degree of mixing has a very large effect on the size of sample required and there are still too few experimental data to show at what stage of coal handling most of the mixing occurs. The discussion states that the weight of material in a screened fraction, or in a float-and-sink fraction, is more important than the mixing factor. We do not believe that these factors are comparable in this instance inasmuch as our purpose was to give minimum sampling requirements to achieve a preassigned accuracy in the percentages of float, middlings, or sink, and nothing more. The gross sample had already been screened and no further division by screening was made or contemplated; also, it was not intended that the middlings and sink fractions would necessarily be adequate for percentage ash or other determination. In other words, the sample obtained by the method outlined is not intended for washability studies but only for preparation plant control. Further experimental work has been done, since the paper was prepared, to investigate the effect of increasingly larger top and bottom sizes on the variability of float, etc., of a double-screened coal from Western Pennsylvania. Results will be published and eventually attention is to be given to the preparation of sampling specifications. E. H. M. BADGER*—I should like the authors to explain more fully the fundamental assumptions on which their Eq 4 is based. The equation is of the form s2 = p(l - p) which is the usual expression for the (standard deviation)2 when the chance of finding a particular kind of particle in the sample is proportional to the number fraetion, p. But instead of the number fraction, the authors have used the weight fraction, WF/W. The chance of finding a particular kind of particle in the sample can only be proportional to the weight fraction, if the average ?eig?ts of all kinds of particles, that is, float, midlings, or sink, are the same. Surely a much more justifiable assumption would be that the average volumes of the particles are the same, and, if this is so, Eq 4 would not be true. This may be demonstrated as follows: Let be the weight fraction of float, middlings, or sink, dl the density of this fraction, and d2 the density of the rest of the coal. Then assuming that the average volumes of the pieces in the three classes are the same, the number fraction, p, is given by ? P = d1/l-?/d2 + ?/d1 = ?d2/d1 + ?(d2-d1) The weight fraction, w, in terms of p is given by ? = pd1/(l-p)d2 + pd1 = pd1/d2 + p(d1-d2) _____ [61

Jan 1, 1950

By J. A. Stachura

Continuous mining machinery provides the coal industry with one way to compete for a larger share of the total energy market. Various types of machines are discussed and some of the problems with continuous miners, encountered by operators, are reviewed. Equipment manufacturers are working with mine personnel to provide solutions for problems that arise. While coal production over the past 25 or 30 years has been on a horizontal plane, coal's share of the total energy market has declined. To participate more effectively in this total energy market, it is necessary to produce coal more efficiently. It is the obligation of all management, employes, and mining departments to gear the deep mining industry to the rapid progress and changing of today's modern industry. This can be accomplished in the near future with the selection of the proper type of continuous miner best suited to each operator's individual situation. In most mining operations there is tremendous incentive to undertake the continuous mining program. It can reduce the size of the mine greatly by permitting a minimum of working places; it makes pillar recovery work more efficient from the standpoint of overall cost, amount of coal recovered, and safety. The work force can be reduced materially permitting closer and more efficient supervision. It simplifies maintenance because equipment can be more readily standardized. The trend of the coal market favors the use of continuous mining machines. Although there appears to be a general feeling that continuous mining is still a relatively new program and will be slow in replacing conventional mechanical equipment, the fact is that tremendous strides have been made since the first machines were installed in 1948. This program is advancing at approximately the same rate that mobile loading machines replaced hand loading. From 1948 to 1955 there were approximately 450 continuous mining machines in service. In October 1959, a survey revealed that there were more than 700 continuous mining machines in service. Many operators have expressed a desire to undertake this program, but they feel that they could not do so at this time because of one or more of the following reasons: 1) the thickness of their coal seams, 2) seam characteristics, 3) soft bottoms, 4) bad roof conditions, 5) size consist, 6) insufficient flexibility in machines, 7) difficult ventilation problems, and 8) high maintenance costs. With the realization on coal about the same today as it was in 1948, or slightly less and since coal is still failing to participate to a greater degree in the total energy market, it is not surprising that the coal industry is desperately exploring more economical methods for deep mining. The manufacturers are aware that the coal industry is willing to invest in continuous miners if the equipment is built for maximum flexibility, will produce higher tons per man, and assure long life between overhaul programs. CONTINUOUS MINING MACHINES Before discussing details regarding the selection of a continuous miner, let us have a preview of some of the continuous mining machines which are available to the coal industry today. Jeffrey Manufacturing Co.: The machine shown is the Jeffrey 76 A.M. Colmol. This is their most widely used miner, and has been particularly successful in central Pennsylvania and in high-wall mining in western Kentucky. One of the outstanding features of this auger-type miner is its portability. The entire mining range can be changed from its lowest point to the maximum height without stopping the mining operation. Jeffrey 76 B.M. Colmol: This machine is similar to the 76 A.M. model; however, it is built bigger and stronger for a mining range of 50 1/2 to 72 in. This is the model that is now available (Fig. 2). Jeffrey has added two arms to the top row, omitted the odd arm in the bottom row, thus permitting a 50 pct larger throat opening. This eliminates one

Jan 1, 1961

By H. J. Rose

Sixty-five million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 Table 1.—Production and Disposition of Ocen Coke in 1924 By-product Beehive Total Coal charged into ovens, tons................ 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons............................. 33,983,568 10,286,037 44,269,605 Average yield of coke, per cent ............. 69.3 6.46 68.9 Disposition of coke, per cent.: Blast furnace.......................... . . 82.6 Foundry............................... . 13.3 6.6 Domestic.............................. . 1.4 6.7 Water gas manufacture and all other uses.. 4.6 . 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke. Suitable Coals The examination and development of new sources of coking coal are important because of the irregular and limited distribution of high-grade

Jan 1, 1927

By R. B. Adair, J. S. Browning

The laboratory batch and continuous flotation pilot plant tests demonstrated the technical feasibility of recovering high grade mica concentrates from weathered mica pegmatite ores of Alabama and Georgia. The research indicated that combinations of anionic and cationic collectors may be used effectively for flotation of fine size mica from weathered pegmatite ores. In continuous tests, concentrates containing 98.5% mica were obtained from the Georgia pegmatite ore; the Alabama pegmatite ore concentrates contained 98.4% mica. The recoveries were 91 and 89% respectively. INTRODUCTION The principal uses of fine ground mica are as a filler in wallboard joint cement, as a filler and surface coating for roofing, as an ingredient in paints, and in oil well drilling mud. The mineral has other uses in the manufacture of rubber, wallpaper, plastics, welding rods, electric insulation, house insulation, and textiles, and as an annealing agent in metal treatment. In recent years, more than 99% of the domestic mica produced has been scrap and flake mica (mica which does not meet specifications for sheet mica and is used for producing fine ground mica). There has been a continued increase in mica production for several years, the 1963 production of scrap and flake mica totaling 117,251 tons.1 Ground mica is obtained primarily by crushing and milling pegmatites and schists. To a lesser extent, mica is produced as a byproduct of kaolin washing and feldspar and spodumene flotation operations. The processes used in recovering mica by crushing and milling pegmatites are generally simple, consisting of various combinations of alternate roll crushers and trommel screens that separate the mica and gangue at screen sizes coarser than 6-mesh. As these processes are designed to recover only coarse mica, high losses in the plant rejects are common. Large tonnages of tailings from the crushing and screening plants have been accumulated in a number of areas. Methods for treating such products were developed by the Bureau of Mines in 1941,2 but have not been generally applied. More recently, mica flotation research has been completed and published by the Bureau of Mines.3 These methods required complete removal of 150- to 200-mesh materials from the flotation feed with consequent fine mica losses. Later, the Bureau of. Mines investigated methods for-recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials, but not so drastically as to remove the fine sands. This report summarizes the results of these studies. The process developed was effective on pegmatite ores from two locations and should be applicable to the commercial treatment of other mica-bearing pegmatite ores and fine rejects that have been accumulated at various mica-milling operations. DESCRIPTION OF ORES The ores used in the investigation were obtained from the Dixie Mines, Inc., Heflin, Alabama, and the Ruberoid Corporation, Hartwell, Georgia. The sample from Alabama contained muscovite and quartz, with a high percentage of clay, and minor amounts of biotite, kaolin, limonite and tourmaline. The mica in the ore was essentially all minus 4-mesh in size and was free of attached mineral grains. The Georgia sample contained muscovite and quartz, with minor amounts of biotite, kaolin, and limonite. The mica in the ore, which was essentially all minus 4-mesh, was liberated. Petrographic analyses of the two samples are given in Table I. THE ANIONIC-CATIONIC MICA FLOTATION METHOD Previous investigators2,3 have reported that complete desliming of mica ores at 150- to 200-mesh was required prior to flotation with cationic collectors to obtain satisfactory selective separation of the mica from the other mineral components. Numerous tests were made at the Tuscaloosa Metallurgy Research Center to determine if some reagent combination could be used to selectively float finer size mica without complete desliming. The investigation led to development of a process using a simple reagent com-

Jan 1, 1967

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961