Search Documents

By D. M. Given

HOW much can the mine operator afford to spend on his coal burning boiler plant? The usual answer is as little as possible and still get the job done. Thus, attention must be focused on the spot where excessive costs are most likely to arise - the materials handling end of the job. Boiler plants consuming less than 30,000 tons of coal annually can be controlled to the point where costs for handling coal and ashes are under $1.00 per ton. There is a wide selection of coal and ash-handling systems that can be used in smaller boiler plants to provide labor savings and convenience required if management is to accept coal as fuel.

Jan 7, 1953

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

This paper reviews the likelihood of instability occurring within coking coal cargoes from BHP CoalÆs northern Bowen Basin mines. In coal cargoes, initial moisture redistributes vertically towards the base, saturating the bottom layers unless the bilge wells are pumped regularly. There has been concern in some quarters that saturated coal in the basal layer may be prone to liquefaction, and if the vessel then rolls significantly in rough seas, overall sliding movement of the cargo might occur. However, a review of shipping accident statistics reveals that casualties relating to shifting of coal cargoes are quite rare, and have not occurred in modern large bulk carriers (>15 000 dwt). The moisture redistribution process has been analysed to quantify the extent of cargo saturation that may occur. Results indicate that the amount of redistribution increases with initial moisture content above a threshold of eight to nine per cent. However, the removal of water by pumping from the bilges is remarkably effective in reducing the extent of saturated coal (and therefore the possibility of cargo liquefaction and movement), and in controlling the average moisture content of the bottom layers of cargo. Stability analyses were then performed for deep sliding of a cargo with a saturated and liquefied base. These have confirmed that sliding of a cargo with a liquefied base during rough seas (20¦ roll angles) would require initial total moisture content exceeding 13 per cent, the hold half full or less (width/depth >3), and no bilge pumping so that height of the saturated zone is as deep as possible. Overall, the results indicate that coking coal cargoes from BHP CoalÆs northern Bowen Basin mines will be unlikely to suffer sliding or liquefaction failures when transported in modern large bulk carriers.

Jan 1, 1997

By W. A. McCurdy, Joseph W. Leonard, T. S. Spicer

INTRODUCTION by T. S. SPICER and J. W. LEONARD Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is process design, operation and maintenance to produce an acceptable product which can be sold at the greatest possible profit. Because of these interests, attention to the unrealized potential value of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of both the product as well as the tributary coal flow moving through a modem coal preparation plant. Thus, coal types having similar physical and chemical properties tend to become increasingly concentrated according to size, specific gravity and/or surface chemistry. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches which are sandwiched together in layers and which visually differ from each other by physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, six percentage points of dry volatile matter and 10 percentage points of total sulfur.1 Similar wide variations exist for calorific value, seam moisture content and undoubtedly, for any other conceivable coal test parameter which might be used for comparative purposes. These observations all point to the long established fact that coal is not homogeneous as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance. Since both coal and associated minerals entering a preparation plant are highly heterogeneous, a multi-product potential beginning with certain flotation cell concentrates and ending with plant refuse may exist. Such a potential can and to a limited extent is achieved at some operations by drawing off coal according to size, specific gravity and/or surface chemistry differences from individual coal cleaning processes. Such a sequenced draw-off of coal of increasing ash increments could yield, among other products, chemical coals, coking coals, coals for pulverized fuel boilers, cyclone boiler coals, coals for cement plants, limestone, shale and clay. Basis for Coal Evaluation and Selection Despite the known heterogeneity of coal, the final analysis of a given coal product is customarily reported as a single average since coal has always

Jan 1, 1968

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By Frederick J. Rich

INTRODUCTION Coal characterization involves a variety of analyses which are designed to yield as much information as possible about the properties of coal. The types of analyses which are now regarded as necessary for any truly quantitative assessment of coal include the following: 1. proximate analysis 2. ultimate analysis 3. petrographic analysis The two traditional forms of analyses are the proximate and ultimate types. A proximate determination reveals the amount of moisture, volatile matter, fixed carbon, and ash which are present in the coal. Nowadays, a sulfur determination is usually included in the proximate analysis. The ultimate analysis, in contrast, includes a major alkaline oxide determination, which tells how much sodium, calcium, and potassium are found in a sample. Sulfur forms, i.e. sulfide and sulfate vs organic sulfur, are also identified as well as carbon, hydrogen, oxygen, nitrogen, and trace element concentrations. Proximate and ultimate analyses have been used for many years. The petrographic analysis, one which identifies and quantifies organic microcomponents of coal, is a comparatively new technique of coal characterization. Petrography adds great detail to a coal analysis and, to be sure, is a necessary component of any complete analysis. Coal is not at all uniform in its composition. Material from different mines within one coal-producing region will display varia-

Jan 1, 1983

By J. Y. Hwang

The relationship between coal characterization and physical cleaning has not been well understood due to the complex nature of coal. Therefore, it is difficult to apply the results of coal characterization to predict and evaluate the performance of a physical separation (e.g. flotation). Eight U.S. bituminous coals were analyzed and studied petrographically in conjunction with washability and flotation tests. The results show that grindability correlates to ash and fixed carbon contents; liberation determined directly by petrographic techniques is close to liberation determined indirectly by washability; and an ideal separation efficiency can be determined by measuring the inertinite content and the washability separation efficiency using a heavy liquid with a density of 1.4. The ideal separation efficiency was attained for most coals by packed column flotation. The ideal separation efficiency can be used for comparing process technologies and process parameters.

Jan 1, 1988

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By Brij M. Moudgil

Flotation of fine and coarse coal after multistage addition of the frother was found to yield coal fractions with significantly lower ash content as compared to the feed. It was observed that the lowest ash content, specific gravity and reactivity of coal was associated with finer size fractions. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA) with calorimeter attachment. It is suggested that in the ignition stage, the removal of mineral matter affects the reactivity through the physical changes brought about by the ash removal. In the char combustion stage the mineral matter seems to influence the reactivity through the catalytic activity of surface concentrations of metal ions, ratio of combustible/incombustible material, internal pore structure and roughness.

Jan 1, 1984

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By John D. Price

The solution to the problem expressed in the title of this paper might well be condensed into one word, AUTOMATON, But if I were to stop there, even though most of you might applaud, I am afraid that a one-word paper might not justify my coming to this meeting, So let?s explore the matter and try to learn if and to what extent the science of automaton can be applied to the problem of coal cleaning. In taking this approach we must, of course, by-pass the fact that plants In this Country and aborad have been automated to a greater or lesser extent. We will explore the matter from the beginning and not merely take the approach that because others have done it we can do it also. First, let us see just what is meant by automaton.

Jan 1, 1959

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By D. N. Trerice

The Electric Power Research Institute (EPRI) is sponsoring the construction and operation of a coal cleaning test facility at Homer City, Pennsylvania. The facility represents a major investment by the electric utility industry to advance the state of the art of conventional coal cleaning technology. The facility is unique in design and can process large quantities of coal in conventional flowsheet configurations, simulate full size plant conditions, and perform open and closed loop performance testing on conventional and advanced coal cleaning equipment. Computer operation will also be demonstrated. The facility objectives, initial complement, and operating plane are discussed as they relate to other coal cleaning projects at EPRI.

Jan 1, 1981

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By P. Mogodi

The purpose of the project was to propose a coal clearance system (coal transportation system from the mining face to the plant) that could be used for the planned underground operations at Zondagsfontein Colliery. Components of the current coal clearance system were overlooked during feasibility studies. Subsequent studies of the coal clearance system revealed that the combined capacity of the two trunk belts does not match that of the shaft (main) belt. As a result production downtimes will be encountered due to bottlenecks in the system. Ways of addressing this challenge were analysed by weighing both advantages and disadvantages and ultimately a surge bin option was selected. Belt conveyor simulations were conducted in order to determine the optimum capacity of the surge bin. The configuration of the surge bin in relation to the two trunk belts was chosen by considering development cost, advantages, and disadvantages of each option. It was concluded and recommended that a 500 tonnes capacity surge bin is required to remove the bottleneck from the system.

Jan 1, 2010

By S. Tyson

The American Coal Ash Association, Inc. (ACAA) is an organization of producers and marketers of coal combustion byproducts. Since 1968, the goal of ACAA has been to gain recognition and acceptance of ccbs as an engineering material on par with competing virgin, processed and manufactured materials by advancing ccb uses that are technically sound, commercially competitive and environmentally safe. The use of ccbs is affected by local and regional factors including production rates, processing and handling costs, transportation costs, availability of competing materials, seasonal adjustments, and the experience of materials specifiers, design engineers, purchasing agents, contractors, legislators, regulators, and other professionals. An annual, survey of coal-burning electric utilities is conducted by ACAA to determine the quantities of ccbs produced and used in the USA. In 1993 approximately 88.5 million tons of ccbs were produced in the form of fly ash, bottom ash, boiler slag and byproduct from flue gas desulfurization (FGD). Approximately twenty-two percent of the combined production of these byproducts was used, while the remaining portion was deposited in disposal areas. The major markets for ccbs include cement and concrete products, structural fills, road-base layers, mineral filler in asphalt, grit for snow and ice control, blasting grit and roofing granules, grouting, coal mining applications, and waste solidification and stabilization.

Jan 1, 1995

By Y. P. Chugh

The use of wooden supports, supplementary to the primary method of roof control using roof bolts in mines, consumes over 3 million cubic meters of hardwood in the U.S. annually. These supports arc primarily used in the form of cribs and posts. Along with a rapid depletion of high quality timber resources, supplies fluctuate seasonally, costs are escalating rapidly, and product quality is highly variable. Environmental considerations of global climate change put additional pressure on deforestation for utilization of timber for artificial supports. On the other hand, management of coal combustion byproducts (GCBs) from power plants has become a major issue to maintaining a healthy coal industry. The USA currently produces over 100 million tons of CCBs annually and the average cost for their management in the US is about $20/ton. This cost is expected to escalate rapidly with tougher environmental regulations. The principal author has been directing research, development, and demonstration studies for CCBs-based artificial supports and lightweight structural materials in mines for the past seven years and has made significant progress toward commercially viable products. More specifically, first and second generation crib elements and post elements have been developed, characterized analytically, and demonstrated in the field. It is estimated that about 2.5 x 10" tons of fly ash could be utilized for artificial supports in U.S coal mines and this would double if these materials were utilized in non-coal mines as well. The author believes that CCBs-based artificial supports have the potential to replace wooden supports and blocks with better performance and cost competitiveness while managing CCBs in an environmentally sound manner. This paper focuses on the development and field demonstration of CCBs-based artificial supports for use in underground mines, and its pilot scale fabrication facility. Recent analysis results on engineering performance evaluation of the developed crib under various loading conditions using finite element method are presented. The following comments highlight the developments: I ). Engineered artificial supports, crib and post elements, using CCBs as a major constituent, have significant potential for application in mines because their structural performance is significantly better than wooden cribs counterparts. 21. Engineered crib elements provide about 50% larger area for air-flow than a conventional wooden crib. 3). Engineered crib elements are not flammable. 4). Each engineered crib element utilizes about 10 kg of fly ash, about 40 % of the weight of crib element- Therefore, a typical crib 2.0 m high utilizes about 200 kg of fly ash. 5). Each 16.5 cm diameter engineered post utilizes 50 kg of fly ash. 6). Assuming 3.0 million cu. meter of wood consumed for post and crib support systems, it is estimated that about 4 - 5 million tons of fly ash may be utilized for supports fabrication in the USA. 7). An engineered post has excellent post-failure characteristics similar to wood. In addition, the engineered post also has excellent loading and unloading characteristics close to the yield point of about 75% of the ultimate load carrying capacity.

Jan 1, 2004

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

The saying that a "prophet" is without honor in his own country does not always hold true, as is shown by the following from one of the local papers, which appeared under the above heading: "Edwin Ludlow, for more than seven-years vice-president of the Le-high Coal.& Navigation Co., with headquarters in Lansford, has resigned, to take effect July 1, when he will take up his residence in New York and engage as a consulting engineer. Mr. Ludlow, during the incumbency of his present position, has demonstrated his efficiency as an engineer and general manager in many directions, notable among which are the almost perfect methods in practice in the inside workings of the several operations under his charge and the erection of the most complete, most practical and most commodious breakers for the preparation of the mine product for market. In addition, his relations with organized labor have been cordial and his dealings with its representatives have been invariably based upon the principle of fair play."

Jan 7, 1919