Search Documents

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024

By Claude Bazin, François Robichaud

The control of the operation of a semi autogenous grinding mill is mainly based on power and bearing pressure measurements. Image based sensors can provide on-line measurements of the size distribution of the ore feeding a SAG mill allowing the control of this variable that impacts the operation of this equipment. This paper investigates the potential of using the information from such type of sensor to maintain a SAG mill feed target size distribution by manipulating the speed of the ore extractors below an ore stockpile. A PID and adaptive predictive controller for the size distribution are studied using a simulator for a stockpile and the equipments used for ore withdrawing from the pile. The proposed controller is found to give a good performance while remaining easy to tune.

Jan 1, 2014

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Rumen Markov, Lubomir Kuzev

"The treatment technologies for municipal solid waste (MSW) are effective mainly for components sized over 40 – 50 mm. This fraction is separated by screening in the beginning of the process. Usually the undersized product is deposited without additional treatment. Its quantity is variable from several up to 30 – 40 % of the total MSW. Both oversized and undersized fractions are formed by all types of primary matter. Adapted technologies from mineral processing will provide a suitable technology for treatment of MSW under 40 – 50 mm. The MSW content depends on the geographical location, the degree of urbanization and other factors. The methods can be applied for separations of different components suitable for recycling or other utilization are: • Separation by density; • Separation in thin liquid layer; • Selective grinding and screening; • Flotation, etc. Introduction Municipal solid waste (MSW) represents an integral part of public urbanization. However, there are some drawbacks stemming from MSW, in regard to its collection, transport and elimination. Different approaches exits worldwide for tackling the problems arising from MSW. For a short period of time, the attitude towards MSW has evolved in several levels, each further level being characterized by higher percentage of utilization of MSW components. Thus, the bottom line has been shifted from safety storage towards processing that includes recycling and maximal utilization of MSW components. Technologic processes applied for treatment of MSW have a common feature – that the fine components, having sizes under 20 mm, 30 mm, 40 mm, or 50 mm are excluded from treatment process trough screening, and in most cases diverted without any additional treatment to preliminary prepared storage sites. MSW in Sofia – current situation The amount of MSW collected daily in Sofia as around 1000 t/24 h. It is stored or baled. Baling is a spare alternative of storage, since baling insures only temporal keeping of MSW, till the building of suitable storage site where the bales will be transported and buried. The morphologic composition of MSW in Sofia has been determined several times at different time intervals, from some Bulgarian organizations as well as from the Japanese organization JICA. So far, however, there is still a lack of enough systematical and comprehensive study. Generalized results from the studies on the MSW components, as well as some important parameters are given in Table 1."

Jan 1, 2008

Provide respiratory protection for escape in a toxic or oxygen-deficient atmosphere with a device small and light enough to be belt-worn. Approach Combine a 10-minute, belt-worn respirator with a stored, larger, long-duration (60-minute) attachment that can be plugged into the 10-minute unit without removing the mouthpiece. How It Works The 10-minute device will be carried by the miner at all times, and the 60-minute canister or attachment will be stored near the miner. In the event of a disaster, the 10-minute device would be donned immediately. The miner would then proceed to the stored 60-minute unit and plug it into the 10-minute unit. For the 10-minute unit, a breathing circuit was developed in which air is passed through the KO2 bed twice per respiration. The 60-minute canister differs from the 10-minute unit in that air is drawn only once through the chemical bed per respira-

Jan 1, 1981

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

The Beloziminskoe deposit in Siberia is a large, potentially productive deposit of rare metals contained in ochreous apatite pyrochlore ores formed by weathering of a carbonatite. The ores are composed of pyrochlore, columbitized pyrochlore, monazite, apatite, magnetite, ferric and manganese hydroxide, titanic iron ore, zircon, hydromica, quartz, feldspar, and carbonates. A gravity-flotation enrichment flowsheet with application of cationic and anionic collectors has been developed. This flowsheet allows for obtaining a pyrochlore concentrate containing 44.3% Nb2O5 and 1.89% P2O5 with recovery of 55.83% Nb2O5 as well as an apatite concentrate containing 39.2% P2O5 and 1.05% TR2O3 with recovery of 62% P2O5 and 43.23% TR2O3 from ores containing 0.92% Nb2O5, 16.9% P2O5 and 0.6% TR2O3. Rare-earth concentrate containing 40% TR2O3 with recovery of approximately 10% TR2O3 was obtained at the same time. Major losses of valuable elements are related to slimes, which make up more than 50% of the ground ore. The niobium concentrate does not meet the phosphorus and radionuclide concentrations needed for the production of ferro-niobium. Acid leaching and sulfatization provided a high level of phosphorous and radionuclide removal. Conditions include hydrochloric acid pre-leaching at 75- 80°C with an 18% HCl solution for four hours and low-temperature sulfatization of acid-leached concentrate at 160-180°C for one hour followed by water leaching of the residue. The apatite concentrate could potentially be processed using nitric acid leaching. This technology is based on decomposition of apatite concentrate with 55-57% strength nitric acid with transfer of rare-earth metals into solution in the form of ammonium phosphate. This technology recovers a rare-earth concentrate containing 95% TR2O3 with extraction of 86%, and highly concentrated polynutrient fertilizer (ammophos) with phosphorus extraction of 95%. The completed research shows how complex multicomponent ores of residual soil may be processed for the extraction of niobium, phosphorus, and rare-earth products.

Jan 1, 2016

By T. A. Chepushtanova, I. U. Motovilov, V. A. Luganov, G. D. Guseynova

"Kazakhstan has significant reserves of oxidized nickel ore with low nickel content. Processing of such ores is effective via pyrometallurgical technologies such as smelting to ferronickel or matte with consecutive extraction of metals from melting products. There are also many options for direct hydrometallurgical processing. However, they do not provide high nickel recovery.We studied extraction of nickel and cobalt by using combined technology of low-grade ore processing from the Shevchenko Kazakhstan deposit, which includes smelting to poor matte followed by hydrometallurgical processing of the matte. The nickel content in the initial ore was 0.75–0.9%. Pyrite concentrate of Sokolov-Sarybai Kazakhstan deposit containing 0.17% cobalt and 0.06% nickel had been used as a sulphidizer at smelting.As a result of the study, we were able to extract up to 98% of the nickel and up to 80% of the available cobalt. Obtained matte contained 3.1% nickel, 0.29% cobalt, 71.6% iron and 24.3% sulfur. Matte leaching was carried out by hydrochloric acid. The iron content in the pregnant solution was 170–185 g/dm3. Nickel and cobalt precipitation from the pregnant solution was carried out by hydrogen sulfide. Initial matte or cast iron was used as neutralizers during the process. Practically complete precipitation of nickel was achieved at 3–5% excess of neutralizer at 333–343°K in 4 hours; up to 95% of cobalt precipitation was achieved in 50% excess of neutralizer at 363°K in 8 hours. The purified solution contained 200–600 mg/dm3 of nickel, 80-100 mg/dm3of cobalt and 175–185 g/dm3 of iron. The purified solution allows to obtain iron oxides by high-temperature hydrolysis, and to regenerate hydrochloric acid.As a result of non-ferrous metals precipitation we obtained sulfide concentrate with concentration of Ni up to 25% and concentration of Co up to 5.5%. The technology is recommended for semi-industrial testing."

Jan 1, 2016

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft&apos;s Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By M. J. Santofimia

Multiphase microstructures in steel have been intensively studied in the past years, but combining non-equilibrium phases still offers a great potential for further development of these steel grades. Thus, improved combinations of mechanical properties can be obtained with microstructures formed by bainite or martensite, in combination with retained austenite. In particular, microstructures on the basis of carbon-depleted martensite and retained austenite can be produced by the very promising production process named quenching and partitioning (Q&P). Originally, the Q&P process aimed to avoid the formation of bainite during the heat treatment. However, the process does provide the possibility for (carbide-free) bainite formation during the partitioning step, i.e. in the presence of martensite. This article evaluates this approach, considering thatthe formation of bainite from austenite is strongly influenced by the preceding formation of martensite. Although the accelerating effect of the presence of martensite during bainite formation has been observed, it is not yet fully understood, and experimental and theoretical studies are being performed in order to come to a more effective exploitation of these processes for the formation of multiphase microstructures.

Jan 1, 2013

By Jean-Pierre Côté, Alexandre Noiseux

"Hatch and ArcelorMittal Mines Canada have combined their expertise to develop a dynamic model of the latter’s Iron Ore Pellet Plant in Quebec, Canada. This model was used to predict the benefits of different expansion projects, as well as asses the best implementation sequence.Two modelling tools were used: a discrete-event simulation software used to develop the dynamic model of the Pellet Plant and an in-house process simulator. The latter was based on operational data and known behavior of the process, and was calibrated with historical data gathered under different operating conditions.The results of the process simulator were used as input values for the dynamic model, which included all of the operation steps of the pelletizing process, from concentrate beneficiation to baking of the pellets. The model has been validated by assessing its capacity to represent adequately the operation of the plant during a 20-month operating period. It was able to reproduce the plant capacity within a precision of 1.2%.Simulated “what-if” scenarios allowed quantifying the production increase associated with the addition of new equipment such as ball mills or balling discs, implemented individually or in combination. Results revealed a potential 10% increase in the annual plant production by adding additional equipment in the two most limiting sectors of the plant, grinding and agglomeration. The simulation results made it possible to quantify the synergistic effect of two projects on plant throughput; the model showed that the combination of two projects resulted in a greater production increase than the sum of the same projects evaluated individually.Now that it has proven reliable, the simulation tool can readily be used by ArcelorMittal Mines Canada process engineers to perform simulations for equipment optimization, and to evaluate the impact of various operating parameters such as equipment availability and tonnage, product mix or concentrate quality. This work showed that a reliable model can be developed based on known parameters in combination with the proper integration of the process knowledge."

Jan 1, 2010

By Nural Kuyucak

Several thousand years ago, metallurgists discovered that by combining two relatively soft metals, copper and tin, they could make a new material, bronze, that was stronger than either metal separately. Bronze and other alloys show how different materials can be integrated to create something new and better. Today?s mining industry can likewise find benefit in an integrated approach to managing the external impacts it has through its waste materials and its use of water. Just as using bronze gave ancient nations an economic and military advantage, mining companies can gain competitive advantage through finding better ways to manage water and waste. Trends pushing this include: ? Environmental ? Regulations on water-taking and the quality of discharged water are becoming more stringent. Net zero discharge requirements are often imposed by regulators. Mining companies also come under pressure to manage environmental impacts of mine waste, including minimizing the area occupied by waste and seepage amount resulting from infiltration of water from a smaller surface area. ? Social ? Particularly in arid parts of the world, there are multiple possible uses for each gallon of water. Local residents do not want to see a reduction in supplies of water for agricultural, domestic, manufacturing and other purposes. They get suspicious about any potential impact of water being mixed with their water reservoirs if it comes from a mining site, even if it would be treated. Such suspicions may cause conflicts among the stake-holders and delays in project approval processes.

Jan 1, 2009

By K. E. Brown, T. D. Murphy

At Monterey Coal&apos;s No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By Hatherly P, Luo X, Balusu R, Gale W

Ongoing, collaborative research between CSIRO&apos;s Exploration and Mining and Strata Control Technology has resulted in a better understanding of rock failure mechanisms around longwall extraction. Failure has occurred further ahead of the retreating face than predicted by conventional longwall geomechanics theory. In some cases significant failure has been detected several hundred metres ahead of the face position with demonstrated influences of minor geological discontinuities. Shear, rather than tensile failure has been the predominant failure mechanism in the environments monitored. Validating technologies of microseismic monitoring and new face monitoring techniques have assisted the development of predictive 2D computational modelling tools. The demonstrated 3D consequences of failure has assisted in the ongoing direction of the project to further investigate these effects.

Jan 1, 1998