Search Documents

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

Factors influencing Cost, systems available for transporting minerals, particularly on land, and methods used for comparing costs are reviewed. A case study presents comparative costs graphically for coal haulage, assumed in Queensland, by 31-6" gauge rail, belt conveyor, 120 ton road train, slurry pipeline, and transmission of electrical energy by transmission line. The effect on comparative results of alternative methods of including initial capital and capital replacement costs is considered and approximate break-even points between systems, bearing in mind the assumptions taken, are discussed.

Jan 1, 1973

By M. L. Requa

IN the fall of 1910, the Nevada Petroleum Co., operating in the Coalinga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.-a record obviously far beyond that made in 1910 by the Nevada Petroleum Co.

Jan 2, 1915

This work describes preliminary laboratory testwork to study the relative leaching response to cyanidation and thiourea leaching of an oxidised low grade gold ore. The potential of an alternative lixiviant like thiourea to commercial processing of mine dumps is discussed by specific reference to selected case histories. It would appear that on the basis of the available published information, there could well be a case advanced for the acid thiourea leaching of sulphide concentrate tailings being subjected

Jan 1, 1994

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By Neil C. Hario

The purpose of this paper is to explore the various designs and design alternates available for large fine crushing plants, and to discuss objectives and criteria upon which these designs are founded. Common practice for size reduction of run-of-mine or run-of-pit ore in preparation for subsequent treatment utilizes a three-stage system. First stage, or primary breaking is generally carried out with jaw or gyratory crushers. The usual output from this stage provides a feed for fine crushing in the size range of 6 to 10 inches. This discussion is limited to the process of fine crushing, and we will further limit it to what is commonly called secondary and tertiary crushing. We define a large crushing plant as one with a minimum capacity of 2,000 tons per hour. Generally, these plants utilize cone type crushers to reduce ore for rod, ball, or pebble mill feed.

Jan 1, 1970

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By H. Sevim, M. K. Mohanty, Y. P. Chugh

The economics of “Conventional” and “Advanced Fine Coal Cleaning” (AFCC) circuits for refuse pond reclamation as well as active mine/preparation plant applications have been evaluated. The benefits of innovative tailings management schemes on the profitability of mining enterprises have also been evaluated as a part of this study. Analyses have been conducted for scenarios involving generation of two different product qualities of 5.81%, a quality that was obtained during AFCC circuit operation at SIU, and a more typical 8% product ash. The inability of the conventional circuits to achieve profitability while producing the lower ash content product is revealed from this approach. The spiral-only circuit is unable to produce a 5.81% ash product. A different version of the same circuit involving spirals and column flotation produced the desired product quality but could not maintain profitability. The AFCC circuits on the other hand, achieve net present values greater than $6 million, with return on investment in excess of 50%, in the water-only as well as dense medium mode, with and without tailings management. Addition of tailings management system to any of the circuits is found to enhance the project economics. The comparison of water-only and dense-medium applications of the AFCC circuits indicate a better suitability of the dense-medium circuit for producing premium quality products. Application of AFCC circuits in active mines offer better economics compared to applications in refuse pond recovery operations. The superior project economics are a result of reduced overhead cost and use of existing material handling facilities. Sensitivity analysis reveals the significance of capacity utilization on project economics.

Jan 1, 2002

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By F. Milton Lewis, James L. Coburn

In this paper the economics for a conventional comminution system, consisting of three stage crushing and one stage ball mill grinding, are compared to a semi-autogenous/ball mill comminution system. Capital and operating costs for a copper concentrator in Arizona at two levels of production, 20 and 40 thousand short tons of ore per day, are estimated. In order to minimize the investment and operating costs, large size equipment is selected for all four cases. These cost data are evaluated and conclusions are presented.

Jan 1, 1982

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

By D. R. Spink, D. N. Okuhara

Two reagents have been proposed for the commercial extraction of copper from leach liquors, namely LIX64N produced by General Mills Chemicals, Inc. and Kelex 120 produced by Ashland Chemical Company. Each of these reagents consists of an active extractant and an additive. In the LIX system, the additive improves the kinetics of the extraction reaction whereas for the Kelex system, the additive acts primarily as a third phase inhibitor. Equilibrium and kinetic studies have been conducted with both systems. In general, the Kelex system effectively extracts copper at a lower pH than LIX64N; furthermore, the rate of extraction with Kelex is considerably faster than with LIX which indicates that systems employing the Kelex extractants might also be able to employ agitated columns rather, than mixer- settlers which are absolutely necessary for effective extraction with the LIX reagents.

Jan 1, 1973

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32' x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18' x 5' Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5' x 12' vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer 's underflow are dewatered on a 13'[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982

By J Loimi, P Minkkinen, T Korpela

The head loss caused by metallurgical sampling for slurry streams can be reduced by metallurgical sampler design. When the process volumetric flow rate is reduced by vertical static cutters before the sampling by an equal number of moving cutters to the static cutters, the installation requires less installation head space than other sampling arrangements and is easy to accommodate at suitable locations in the process. Low head loss reduces building costs for the processing plant and operational costs during the lifetime of the plant.The presence of a possible systematic bias in the particle size distribution, solids density and elemental composition between an Outotec MSA 2/50 metallurgical slurry sampler sample and MSA 2/50 manually sampled reject have been studied by a customer. The paired samples were taken as simultaneously as possible. The customer evaluated the possible bias using a paired t-test and provided the assay results to Outotec for further evaluation.The results of the paired t-test showed no systematic bias in particle size distribution, solid density or assayed analytes, except in one analyte with low content and a high relative error. The high relative error in one analyte may have been caused by the same calibration model used in a X-ray fluorescence analyser for both high elemental-content concentrate and very low elemental-content tailings samples. The sampled stream is the tailings of a previous process stage.The results of the t-test were studied further using analysis of variance to reveal the error sources in samples. The results showed no bias between the samples collected from the MSA 2/50 reject and composite samples collected of the MSA 2/50 sample stream. The courier online analyser data was also available for evaluation of representativeness to the process stream.The analysis results of the courier online analysis reveals no bias between the MSA 2/50 reject samples, MSA 2/50 sample stream composite samples and online analysis results during the comparative sample collection period.CITATION:Loimi, J, Minkkinen, P and Korpela, T, 2017. Comparative evaluation of manual sampling and Outotec MSA 2/50 metallurgical slurry sampler, in Proceedings Eighth World Conference on Sampling and Blending , pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By William J. Cavanaugh

In 1967, Lone Star Industries, Incorporated, established a program to carry out the necessary Research and Development work to bring the Snyder Process to commercial application. The purpose of this paper, is to present the detailed metallurgical results gathered in comparing the Snyder Process of Comminution to conventional grinding techniques for the milling and beneficiation of certain ores and other materials. The ore primarily dealt with in this paper is a fine-grained magnetite ore, containing approximately 23% acid-soluble iron, from the Lake St. Joseph ore body of Steep Rock Iron Mines, Ltd., (Canada). This particular example was selected for presentation in this paper because extensive comparative results with conventional methods of grinding were available. Also briefly described in the paper are the comminution of other ores and materials such as porphyry copper ore and alumina.

Jan 1, 1973