Search Documents

By Yi Zheng

Under normal circumstances, methane released along a longwall face represents only 10%-20% of the total me- thane emitted from the entire longwall panel. However, there might be a sudden surge of methane at the face which may cause a potential problem because the friction from shearer cutting, support movement, and scraper conveyor dragging can be ready ignition sources. Therefore, to predict the distribution of methane will be critical to prevent possible explosions. In this paper, methane dispersion patterns along a lognwall face are simulated under normal and abnormal conditions. With the simulation of methane released from the face, around shearer drum, and from the broken coal on the conveyor, places with possible high methane content can be identified by different phases of working process and shearer positions. Local ventilation measures are evaluated so precautionary measures can be planned ahead.

Jan 1, 2012

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By H. Singh, Anupam Agrawal, H. S. Grewal

"Erosion in industrial appliances causes huge loss of valuable resources especially when solid particles are present in the working medium. A number of erosion models that are available in the literature claimed to predict the erosion response. In this work, five erosion models have been evaluated using computational fluid dynamics (CFD) methodology. Three most commonly used experimental test rigs (solid particle and unsubmerged slurry jet type and pot type) have been simulated and comparisons with the experimental results have been performed. The study helps in understanding the effect of fluid medium and flow pattern on the erosion process. The knowledge acquired shows that phenomenological based erosion models give better results considering the wide range of operating parameters. The in-depth study of the flow field shows the possibility that erosion mechanism, being parameter dependent, could change with location on the same specimen.1.0 IntroductionErosion is a surface degradation phenomenon which causes the removal of material due to impacts either of solid particles and/or bubbles or gas entrained in a fluid medium. Erosion has various categories depending upon the erosion medium such as, solid particles erosion (solid particles entrained in gaseous medium), slurry erosion (solid particles entrained in liquid medium) or cavitation erosion (erosion caused by exploding gas or vapor bubbles). Humphrey [1] has listed 21 different factors that decide the erosion response of the components under a given working condition. The number of factors involved in the erosion process gives us an idea about its complex nature."

Jan 1, 2012

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By C. V. Umipig, G. G. Hutalle, E. E. Israel

TVI Resource Development (Phils) Inc. Canatuan mine is a polymetallic ore deposit located in the Province of Zamboanga del Norte on the island of Mindanao in the Philippines. The deposit consisted of an oxidized capping of gossan overlying a Besshi type volcanogenic massive sulphide lens which is near surface and flat lying. Construction and development of a sulphide processing plant began in early 2007 and commissioned in November 2008. During the initial stages of sulphide operation, high copper (Cu)-low zinc (Zn) ore was fed to the plant. Marketable copper concentrate at 91-95% recovery was produced utilizing a high-pH bulk sulphide rougher flotation and 2 cleaning stages. Because of increased levels of Zn of the ore body, a Cu/Zn separation circuit was initiated in early 2010 following an intensive laboratory test work program. This Cu/Zn separation circuit was necessitated because of the copper ion pre-activation of the sphalerite that lead to the zinc being readily recovered to the copper rougher concentrate. In-situ activation of zinc (in the pit and stockpiles) was caused by the leaching of secondary copper minerals in the ore (particularly from the dominant copper species, chalcocite and covellite). This problem required the development of metallurgically complex and intensive reagent regime to effectively depress the activated sphalerite. As well, the immediate reactivation of zinc after it has been depressed, at the onset of Cu/Zn separation flotation, added additional metallurgical complexity to the process. Subsequent to the Cu/Zn separation circuit, an unconventional, yet proven effective, simultaneous cyanide detoxification-zinc flotation circuit was set-up to recover the zinc. Laboratory test work results realized Cu-Zn recovery differential from a Cu/Zn separation circuit of over 40-45%. This performance has been achieved in the plant, at 72% Cu overall recovery. With the gradual improvements on-going with zinc circuit capacity and effective zinc separation being achieved, zinc recovery has currently reached 40%.

Jan 1, 2012

By Bryan Ulrich

On March 15, 2012, about 24 attendees from several western states attended Roundtable 2012, hosted by Knight Piésold and Co. at the Red Lion Hotel and Casino in Elko, NV. The focus of this year?s discussion was ?Acid Rock Drainage for Engineers and Environmental Scientists.? Other names may have been more suitable for the event, perhaps combining geochemistry, with air and water quality and their long-term effects on soil and rock mechanics. Bryan Ulrich (senior vice president, Knight Piésold?s Nevada operations) and Steve Lange (senior geochemist, Knight Piésold, Denver, CO), helped facilitate the discussion. Attendees included personnel from a dozen mining properties, various corporate offices and academia. There were also attendees from a geochemical testing laboratory to help respond to specific questions pertaining to testing protocol and procedures.

Jan 1, 2012

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By J. -C. Parisien-La Salle, D. Blais, G. P. Demopoulos

"In this work the dissolution, precipitation and adsorption behaviour of gold in acidic iron sulphate media containing small amounts of chloride ions is investigated via batch laboratory tests and OLI thermodynamic calculations over the temperature range 25-250°C. Chloride ions may be present in industrial pressure oxidation/pressure leaching (POX/PL) operations due to elevated water salinity levels or due to intentional addition as is the case of the CESL Copper Pressure Leaching Process. Thermodynamic calculations show that AuCl4 - may form depending on the free Cl-/Au ratio and temperature, its stability increasing with increasing Cl- concentration and decreasing with increasing temperature. On the other hand during POX/PL, we know that massive precipitation of iron in various hydrolysis products and compounds occurs. Hence of interest is the question how AuCl4 - that may form during leaching interacts with the iron precipitation products. Gold(III) chloride was found to co-precipitate with iron(III) (oxy) hydroxides and arsenates forming in the autoclave but not with natrojarosite. Upon further investigation it was discovered that activated carbon added in the autoclave (as done in CIL) acts as preferential sink for the mobilized gold, hence opening the potential for the development of a direct cyanide-free gold recovery process in acidic sulphate leach reactors.INTRODUCTIONThe recovery of gold from ores and concentrates has evolved over the years with processing routes becoming increasingly complex. Given the high value of gold, any reduction in losses during recovery operations constitutes an important economic benefit. One such loss that needs to be addressed is the potential solubilisation of gold during pressure oxidation (POX) of refractory sulphidic gold feedstocks. For example, Agnico Eagle Mines reported a loss in gold recovery due to the formation of a gold chloride complex (Garofalo, 2009). Gold is known to form complexes in solution, such as gold(III) chloride, if an excess of chloride ions are present. The fate of such soluble gold chloride during pressure oxidation and the subsequent neutralization of the acidic discharge slurry will determine if gold is lost or recovered in the downstream cyanidation operation. Thus it is of interest to know under what conditions gold chloride may stay soluble or co-precipitate along primary (formed in the autoclave) or secondary (formed during neutralization) precipitates. Furthermore, the mode of co-precipitated gold, such as adsorption on iron compounds, like goethite and hematite (Machesky et al., 1990; Nachayev, 1984); substitution in one of the precipitated phases; or finally chemical reduction to metallic state would have consequences in terms of gold recovery."

Jan 1, 2012

By Brian G. Thomas, Quan Yuan, Rajneesh Chaudhary, Rui Liu, Sana Mahmood

"A particle-entrapment model based on local force balances has been developed, implemented into computational models of turbulent fluid flow, and applied to simulate the entrapment of slag inclusions and bubbles during the continuous casting of steel slabs. Turbulent flow of molten steel is computed in the nozzle and mold using transient CFD models. Next, the transport and capture of over 30,000 particles are simulated using a Lagrangian approach. Particles touching the dendritic interface may be pushed away, dragged away by the transverse flow, or captured into the solidifying shell according to the results of a local balance of ten different forces. This criterion was validated by reproducing experimental results in two different systems. Finally, the model is applied to predict the entrapment distributions of different sized particles in a typical slab caster. Although more large particles are safely removed than small ones, the capture rate as defects is still high.IntroductionSurface defects such as slivers and blisters are often caused by captured inclusion clusters, slag, bubbles, and other particles. During continuous casting, jets of molten steel from the submerged entry nozzle (SEN) ports carry bubbles and inclusion particles into the mold cavity from upstream processing, as shown in Figure 1 [1]. In addition, droplets of liquid mold slag may become entrained into the flowing steel due to fluid flow problems, via several different mechanisms [2]. Figure 2 shows some typical inclusion particles [3] that can be entrapped from the flowing liquid into the solidifying steel shell to form defects in continuous-cast product.Liquid steel flow in the continuous casting mold has been modeled extensively. Reynolds Average Navier-Stokes (RANS and URANS) approaches are based on accurate computation of the ensemble-averaged velocity field. Particle transport can be tracked using a Lagrangian approach, introducing an extra model, such as ""random walk"" to generate realistic motion of every particle. Large Eddy Simulation (LES) models can accurately calculate both the transient evolving flow field and Lagrangian particle motion [4, 5] of this turbulent process."

Jan 1, 2012

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012

By Lloyd Buckingham

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012