Search Documents

By A. A. Wessels, D. P. Allison

"Mine hoists are built to handle a certain nameplate capacity; they are specified and designed according to the required duty. However, as production capacity increases in other parts of an operation, the hoist capacity can become the critical constraint. Such a situation occurred at Lundin Mining’s Neves-Corvo operation. This paper examines how each component of the existing hoisting system was examined and optimized. Through a combination of engineering study and hoist simulations, the annual hoisting capacity was improved by 24% through increases in payload capacity and available hoisting time combined with a reduction in cycle time, while no changes were made to the hoist motor, drum or headframe. The additional payload capacity was achieved by reducing the mass of the hoist ropes and skips, and improving load monitoring systems. The cycle time was reduced through the shortening of the creep distances and increased availability through the installation of a shaft collar safety platform, alternative guide rope bushes, and superior liners for both the skips and underground measuring flasks. Enhanced cooling of the hoist electrical system was also incorporated to increase hoist availability by reducing downtime during hot summer months. The changes will increase the capacity from the current 4.5 mega tonnes per annum (Mtpa) to a planned 5.6 Mtpa and are being implemented over a 2-year period whilst maintaining the mine production during the upgrade work. INTRODUCTION Neves-Corvo Mine Neves-Corvo is primarily a copper and zinc mine producing copper, zinc and lead concentrates. The operation is owned and operated by Somincor, the Portuguese subsidiary of Lundin Mining. Located in the Alentejo district of southern Portugal, the operation is situated approximately 15 km southeast of the town of Castro Verde, where summer temperatures can reach as high as 45ºC, and approximately 220 km southeast of Lisbon. The principal means of mine access is via a ramp from surface, with the vertical shaft used to hoist ore and waste from the 700 m level, while conveyors descend from the 700 m level to transport ore and waste up from the deeper levels of the mine. The mine is highly mechanized and several different stoping methods are employed, with the most significant being bench-and-fill and drift-and-fill. The Neves-Corvo mine currently exploits five orebodies: Neves, Corvo, Graça, Zambujal and Lombador for copper and zinc-lead ores which are processed in one of two plants. All the orebodies are currently exploited over their full elevation with the exception of Lombador which is only mined down to the 220 m level, approximately the top 50% of the orebody, known as Lombador Phase 1."

Jan 1, 2019

By A. Esterhuizen, S. Essack, H. Joubert, N. Fowler

Tenova Pyromet has developed innovative technologies for copper smelting and electric slag cleaning furnaces. Based on client feedback and requirements, innovative designs have been developed to address key design areas and improve furnace reliability, operability and hygiene. These developments include the NovaLance™ lance system to prevent lance bending on top submerged lance furnaces, the SlagFlo™ slag tapping flow control device to better control bath levels and tapping rate for granulation, and an electrode seal for improved sealing directly onto the electrode casing to allow water-cooled electrode components to be located above the furnace roof. The potential application and benefits of these innovative designs are discussed. INTRODUCTION Tenova Pyromet has a long history in the engineering and supply of innovative electric furnace and related equipment for the base metals and platinum industries. Recently Tenova Pyromet has used its furnace equipment design experience to engineer innovative solutions for top submerged lance (TSL) furnaces, and potentially other furnace technologies. These equipment design solutions are developed to address specific operating challenges and operator requirements. Three of these innovative equipment developments are discussed in this paper. First the NovaLance™ lance technology to prevent lance bending during operation in TSL furnaces, such as used for primary copper smelting, is described. Lance bending has been identified as a significant problem for TSL furnace operators as it causes down time and affects furnace availability. The SlagFlo™ device to control the slag flow rate during tapping has been developed based on specific requirements in the mineral wool industry. The SlagFlo™ device can be used to control slag bath levels in primary smelting, converting and slag cleaning furnaces for base metals including copper. In addition, it can be remotely activated for the safe closing of slag tapholes located upstream from a water granulation system. Finally, Tenova Pyromet developed an electrode seal that seals directly onto an electrode surface. This is a special requirement related to base metals and platinum electric smelting and slag cleaning furnaces where furnace operators prefer to keep the water-cooled electrode equipment above the furnace roof. The seal can be used to seal directly onto the potentially hot and uneven surface of Söderberg, pre-baked and graphite electrodes.

Jan 1, 2019

By A. Ghahreman, M. Oliazadeh

"Heap leaching is an attractive process for low grade deposits where the metal content of ore does not justify the high cost of milling and agitated leaching. In general, the heap leaching capital cost is low, construction is rapid, and production costs are low. The primary disadvantage of heap leaching is low recoveries (typically 65% of agitated leach recovery); thus, recovery improvements could convert more lower-grade deposits into minable reserves. This will also allow to process primary sulfide ores and result in a dramatic expansion of the technology, as ~80% of total ore types are sulfidic in nature. The old gold operations tailings are another massive source of low-grade gold material that can be retreated by the heap leach process. The major parameters affecting the recovery rates are ore characteristics (mineralogy, particles size of metal and host minerals, ore permeability), and operational conditions (segregation of ore, compaction, leach cycle time, lift height, and solution application rates). The design of a percolation leach process is based on a limited number of coarse ore bottle roll and/or column tests under ideal conditions. The economics of the projects and engineering design of the process facilities are developed based on the bench scale test work results and the application of the conventional engineering scale up factors. This paper will deal with the parameters affecting the HL efficiencies and focus on the potential improvement of gold heap leach recoveries. This would include design of heap leach operation and evaluation of processes such as fine crushing and bioleaching.INTRODUCTION Gold heap leaching is a hydrometallurgical process designed to treat amenable low-grade gold ores that contain typically 0.5 to 1.5 g/t gold (Marsden and House, 2006; Wong Wai Leong and Mujumdar, 2010). Ore is stacked by various types of equipment on an impermeable barrier, and a sodium cyanide solution is applied to the surface of the stacked ore. Gold, silver, and other metals contained in the ore are dissolved to various degrees by the cyanide application, as it percolates downward through the stack of the ore. The pregnant leach solution (PLS) is then collected at the bottom of the heap. The PLS is then sent to the gold recovery plant where the metals are extracted. The barren leach solution (BLS) is then reapplied to the top of the pad. Ore is placed on a pad or previously leached lift by various means, including ramp conveyor belts, radial-arm and self-leveling stackers, and trucks. Once trucks are used to construct the pads, the pad can be compacted and hence the pad should be graded and ripped or scarified (roughened up) with wheeled or tracked equipment to produce shallow cuts to increase surface area exposure to the leachate."

Jan 1, 2019

By E. Vesely, A. Saxena

"SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Because of the collisional environment directly measuring such dynamical loads is extremely difficult if not impossible. In this study we tried to evaluate the liner failure risk by simulating the collisions of solid particles with mill liner using Discrete Element Method (DEM). DEM simulation has been proved to be a very useful tool in evaluation of granular flow and its impacts on the solid structure. But there are certain limits in DEM coherently, such as the number of solid elements, the computer runtime, etc. Here we first present the general feature of the particle-liner collision in terms of impact force and collision energy. Then the effects of parameter selection is discussed. Our simulations show the fatal collisional event of huge impact force is very rare and the collisional events of low impact is much more frequent. The fatal event may contribute most to the liner failure. The rarity of the fatal events may be missed in a short runtime simulation. This technical challenge combined with lacking of criterion to evaluate varying impact loads in fatigue problems may further complicate the evaluation. Should we use the largest impact force alone or we should use the more frequent events is an open question and requires more effort. In order to evaluate the quality of liner design, we proposed a relative comparison method. In the end we show the implication and application of this method in liner optimization by a work example. In particular, the effects of the charge level of grinding balls and their size on the operation performance is presented.INTRODUCTION Grinding is one of the most important and expensive steps of mineral processing. A variety of grinding mills such as rod mills, ball mills, semi-autogenous (SAG) mills and autogenous (AG) mills are being utilized for comminution of mineral ores (Gupta & Yan, 2016). Up to today, SAG mills and AG mills have been widely used to reduce operation costs and increase throughput. In an AG mill, a rotating drum throws larger rocks of ore in a cascading motion which causes impact breakage of larger rocks and compressive grinding of finer particles. Unlike AG mills, SAG mills use steel grinding balls to break ores of size quite small such that they cannot be easily broken in AG mill. SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Quality and performance of SAG mill liners play a fundamental role to enhance efficiency of grinding mills, because failure of liners is the major cause for unexpected breakdown (Banisi, Hadizadeh, Mahmoudabadi, & Eilkhany, 2006)."

Jan 1, 2019

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By Paulo Couciero

Since explosives are the source of all energy used for rock blast fragmentation and heave, multidimensional effects in the detonation driving zone become essential to better describe the detonation process. In order to use the explosive as an energy source-information for more realist blasting performance simulations, a simple and effective modelling strategy is desirable. Facing this challenge, an engineering approach to two-dimensional unconfined non-ideal detonation is proposed. Based on the elliptical construction of the shock locus, the model combines the axial cylindrical stick Q1D solution with some additional limiting conditions to determine the sonic edge of the charge. For a given set of rate law parameters and velocity of detonation, a complete axial solution is firstly computed through the Q1D model. From this solution, a vital relationship between the axial shock curvature with the shock shape parameters can be stablished. Once this relationship is found, the problem simply reduces in finding the shock shape parameters subject to the sonic edge condition. As a result of this calculation, the corresponding charge diameter can be found. Consequently, the proposed model can map the diametereffect curve by relating the unconfined velocity of detonation with its corresponding diameter. Finally, because of its low computation cost, the proposed engineering approach can be also used for characterizing the rate law parameters by fitting to data from unconfined detonation experiments

Jan 1, 2019

By K. Trapani

"The study undertaken aims to investigate an ice stope heating and cooling system for its potential to be implemented in sub-arctic mines, as a low carbon alternative to conventional natural gas and refrigeration chiller systems. Its performance was simulated for a years’ worth of data, taking into consideration hourly temperature data. Results showed that to supply the required heating and cooling loads, the ice stope system had to supplement its heating with natural heating. The techno-economic performance of this system was compared to that of a conventional heating and cooling system in a mine, with the ice stope thermal storage system hawing the lowest annuitized cost and significantly lower carbon emissions.INTRODUCTIONConventional heating and cooling, in a mine is implemented using natural gas heaters and chiller refrigeration systems respectively. This results in a significant portion of energy consumption in underground mines attributable to ventilation (De Souza, 2015), including the conditioning of the air to ensure that temperatures do not exceed work comfort standards (ACGIH, 2011). Especially at depth where heat could become a significant issue. An ice stope thermal storage, using ice as the storage medium is being proposed as an alternative to provide the heating and cooling—with the ice creation resulting in heating and the ice melting providing the cooling required. A techno-economic investigation of the two systems is undertaken to identify the capital and operating costs for the two systems, and to assess the ice stope’s potential to be considered a low cost and carbon solution for heating and cooling of mines in sub-arctic climates.NATURAL STORAGE SYSTEM – CONCEPT DEVELOPMENTThe concept for the natural storage system is developed from the ice stope at Frood-Stobie Mine, ON, Canada (Stachulak, 1991). The ice stope was developed for mine air heating, with the heating occurring by spraying warm return service water onto the cold intake air—resulting in the air temperature increasing and ice being created in the stope. In summer this ice was melted by passing warm air on top of it, resulting in slight cooling of the air but no significant temperature difference which could allow effective cooling. A schematic of the Frood-Stobie Mine ice stope is provided in Figure 1."

Jan 1, 2019

By C. P. Newman, T. Gray, G. Beale, T. Cluff

Predictive geochemical and limnologic modeling of pit lakes is an important aspect of modern permitting. One of the key assumptions of many predictive pit-lake models is that highwalls and pit backfill become unreactive once submerged by the filling pit lake. Existing pit lakes provide useful data to test this assumption. The Sleeper pit lake (northwestern Nevada) is near hydrologic equilibrium and contains good-quality water that generally meets regulatory requirements for pit lakes. Despite the overall stable geochemical composition, seasonal trends in the hypolimnion indicate the generation of solutes and fluctuations in pH. This work applies mass balance, analysis of subaqueous pyrite oxidation, and trends in solute concentrations to evaluate the potential causes of long-term solute generation in the hypolimnion of the Sleeper pit lake. Results will aid in refining the effect that inundation of highwalls and waste rock has on ultimate pit lake chemistry and long-term closure planning. In the case of the Sleeper pit lake, ongoing solute loading does not substantially change the closure plan at this time as influent groundwater contains abundant alkalinity. INTRODUCTION As mine pit lakes become more widespread, regulatory agencies are increasingly requiring advanced predictive modeling of pit-lake geochemistry during permitting. The end goal of all those involved in these permitting actions (i.e., the mining company, the regulatory agencies, and the public) is to have pit lakes become geochemically and hydrologically stable for the long term, which may then allow mining permits to be relinquished. The modeling endeavors therefore are important to inform long-term closure of pit lakes. The conceptual models and numerical methods used to predict pit-lake water quality are complex and require substantial amounts of data and a variety of assumptions (Castendyk et al., 2015). One of the common modeling assumptions is that solute generation via acid mine drainage is eliminated (or at least decreased) by the filling of the pit lake and inundation of highwalls and any in-pit waste rock. However, few studies have reported on observations that support or refute this assumption. The water-quality record of the Sleeper pit lake is an ideal dataset with which to test these assumptions. The former Sleeper mine is located in northwestern Nevada (Fig. 1), and has been inactive (in terms of ore extraction) since 1996. The mine extracted Au and Ag from the famous high-grade Sleeper vein and associated widespread stockwork mineralization (Nash et al., 1995). Water quality in the pit lake has been monitored since the cessation of dewatering in 1996. The current pit lake actually occupies three separate sub-pits, the Sleeper, Wood, and Office pits (Fig. 1). The Sleeper and Wood pits undergo regular water-column monitoring using a conductivity-temperature-depth (CTD) probe, and sampling for dissolved inorganic constituents at several depths (~10, ~130, and ~330 ft. below lake surface). Groundwater quality is also monitored using a series of wells (Fig. 1).

Jan 1, 2019

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

By G. E. Sreedhar, R. Kumar

The pockets of high silica blue dust across the entire high grade hematite deposits in the Bailadila sector bothers the excavation activity due their iron content, which is higher than the threshold value specified by the Indian Bureau of Mines and the agony of stacking them separately due to their fragile & powdery nature. The physical nature of blue dust and its negligible alumina content makes these a potential source of hematite, which is a blessing in disguise. As most of the particles are in the form of an independent grain making it appropriately suitable feed for dry magnetic separation and thus the dry beneficiation has turned a bane into boon by enabling to produce concentrate either suitable for using as DSO or amenable for blending. The emphasis on carrying out dry beneficiation studies in the present context serves the purpose of mineral conservation, mitigates the issues of excavation and stacking as well as conservation of water resource. This paper describes the laboratory and pilot scale dry beneficiation studies carried out on blue dust of 48 – 60%Fe and Silica up to 30% at 25 Kg/hour to 400 Kg/hour, resulting in production of concentrate assaying 60 – 65%Fe. INTRODUCTION High silica blue dust (HSBD) is associated with Banded Hematite Quartzite (BHQ) and is available in abundance in various pockets across the Iron ore body in the Bailadila region of Chhattisgarh state. High Silica Blue dust occurs in the form of free granular particles and also as friable lumps. The chemical quality of this falls under sub-grade category (45 – 55%Fe) and as per the guidelines of Indian Bureau of Mines, these are to be stacked and conserved as future resources of Iron if it can’t be utilized in the present circumstances. Due to its friable nature, stacking of HSBD is a challenge and it is also compounding the problem by polluting the air under high velocity wind conditions. Because of its physical nature and occurrence in pockets pose challenge to systematic mining. The existing processing set up of the operating mines is designed to treat either Direct Shipping ore (DSO) or Run-of-Mine (ROM) have grade >60% Fe. The present practice of beneficiating iron ore fines (<1 mm) comprise combination of two or more processes such as desliming, hydraulic classification, magnetic separation and flotation apart from requirement of grinding depending on liberation characteristics. The HSBD which is predominantly occur as free granular particles, is significantly low in its alumina content. This gives us an opportunity to utilize them by exploring a suitable beneficiation process so that the concentrate produced can be used as a sweetener for alumina rich iron ore/concentrate. Thus, in the present study, an attempt has been made to adopt dry high intensity magnetic separation technique to explore the amenability of the high silica blue dust for beneficiation.

Jan 1, 2019

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

By A. de Ville d’Avray, G. Guezennec, P. Wavrer, E. Braak

The aim of the European CEReS project was to develop an innovative copper recycling route based on the coprocessing of coal production waste by bioleaching and printed circuit boards (PCBs) from Wastes of Electrical and Electronic Equipment (WEEE). Coal waste is processed by bioleaching in stirred tank reactors, and the resulting bio-lixiviant solution is used to extract copper from PCBs pre-treated by catalytic cracking. Copper is then extracted using solvent extraction, stripping and electrowinning. The whole process flowsheet combines thermal, biotechnological, physical and hydrometallurgical operations. Once the process concept has been validated at laboratory scale, a simulator of the whole process has been built in the USIM PAC software platform. The tool enables to improve the analysis of the results of the lab-scale experiments and to design industrial-scale scenarios by simulation. The results of such simulations allow to estimate the economical interest and to perform environmental impact assessment. After presentation of the CEReS project objectives and main results, the paper describes the methodology used to build the simulator and define the scenarios corresponding to feasible process routes. The main results of the simulations are then presented with technical, economic and environmental point of views. INTRODUCTION Because of rapid technological innovations in the electronics industry, electronic waste represents the fastest growing waste stream in the world, especially in developing countries (Işildar et al., 2018). Meanwhile, the global copper demand is expected to go on rising in the future. As significant amounts of copper are present in end-of-life printed circuit boards (PCBs), it becomes a necessity to develop efficient copper recycling routes. Metal refining from e-waste is traditionally performed by pyrometallurgical processes. However, the hydrometallurgical processing of PCBs, which has been shown to be technically feasible at laboratory scale with a wide range of leaching reagents, could be a less energy intensive and more flexible alternative (Tuncuk et al., 2012). However, a large amount of leaching reagent is required to leach the metals from PCBs.

Jan 1, 2019

By Alexander Levran

The main thrust of this presentation is to illustrate the growing contribution of solar energy to the mining industry by replacing existing mechanical and pneumatic tools and equipment with more effective and efficient electrical tools due to the increased efficiency and lower cost of solar energy generation. LCOE (levelized cost of energy/electricity) for solar energy is becoming highly competitive with other conventional sources of energy. The distributed architecture of solar power plants allows the supply of energy to highly remote and abandoned geographies. We will focus on the trend for this contribution to the mining industry over the next three years. Water desalination and delivery to the mining area will be topic of discussion regarding the contribution of solar systems in Latin America (LATAM) and other geographies. INTRODUCTION Increasing price pressure on the mining industry has generated a strong interest for mining companies to investigate energy costs and consumption. Currently, energy costs in mining economics contribute15% to 25% of the total commodity cost. In the past, most mines were operated by diesel gensets. Very high logistics costs for diesel supply, high and fluctuating diesel prices and theft led to very high energy prices. To overcome this problem, the mining industry has turned to solar energy, employing two main solutions: (i) adding a small scale (single level MWp energy supply) solar to an existing diesel system to create a hybrid solution operating as a microgrid environment; and (ii) replacing the existing diesel system with a large scale grid connected photovoltaic system financed by utilities or private IPP owners that signed a long-term power purchase agreement (“PPA”). In both applications, the near-term trend is to add storage and weather controls to optimize the electrical performance of the system. Use of concentrated solar solution (CSP) in the past was employed in a few remote sites to provide electrical energy to the mines. Currently this technology is not competitive with the photovoltaic (PV) systems. In some installations we have seen usage of a small hybrid system that is designed as relocatable, containerized and delivers scalable electrical power. In addition to the evolution of electrical energy sources, we see the trend of reduction of energy consumption in the mines by optimizing energy efficiency and generating load shifting solutions. Many studies of electrical energy in the mining industry support the growth of this trend in the mining industry.

Jan 1, 2019

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019

By J. Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world´s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards de-carbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain or Germany are only forerunners of this development - their centuries of coal production have been finished. The concept of Sustainable Development (SD) is fundamentally based on a model of progress where ecological, economic and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as: How can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry´s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later. INTRODUCTION Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way, or substitutes are pushing the mined products out of the market. An example for the latter is the increasing replacement of coal with natural gas and renewables in power generation in the USA. (Kok 2017) According to the model of the product lifecycle, the global mining hard coal mining industry has reached the stagnation phase. (Kretschmann 2000) Although the coal mining business is more a multi-regional than a global business the trend is obvious. The peak of coal use is behind us, especially because the coal demand of China is slowly decreasing since 2013. (Shell 2018) China´s government has announced investing $360 billion in renewable energy by 2020 and scrap plans to build 85 coal-fired power plants. In March 2018, Chinese authorities reported that the country was already exceeding official targets for energy efficiency, carbon intensity, and the share of clean energy sources. China’s energy regulator, the National Energy Administration, rolled out new measures to reduce the country’s dependence on coal. (Kejun and Woetzel 2017) Coal consumption in the US is facing a 16 % decline in five years from 800 to 670 million short tons between 2015 and 2019 and - according to the EIA – will not rise again. (EIA 2018) The decline is attributed to complex market dynamics from low gas prices because of the “shale gas revolution” (Kok 2017, p. 3) to federal environmental regulation like the Clean Power Plan. The United Nations´ UNEP Finance Initiative is cooperating with the Portfolio Decarbonization Coalition of institutional investors to implement decarbonization strategies across their portfolio. Amongst these investors is the New York State Common Retirement Fund, the third largest public pension plan in the USA. (UNEP 2017) The European Union has already begun to de-scribe pathways to decarbonization. (European Union 2018) The Norwegian sovereign wealth fund, the world´s largest, excluded coal-related companies for ethical reasons. The oil giants Total S.A. and Royal Dutch Shell, tradi

Jan 1, 2019