Search Documents

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

By Ruifeng Li, Yanghui Ren, Hua Gao

"Since entering the new century, China’s coal industry has witnessed the rapid development, and provided a reliable energy supply for the national economic and social development. But after the “golden decade” of rapid development, the coal industry now is facing overcapacity, low industrial concentration and production efficiency, high pressure of production safety and environmental protection and other prominent issues. Based on defining the connotation of highly-efficient recovery of coal resources, this paper established the relevant 8 indicators to reflect the highly-efficient recovery level of coal resources, summarized the present situation of China's coal resources recovery and the main problems, analyzed the development environment of China's coal industry under the new situation, and finally put forward the strategic measures to promote highly-efficient recovery of coal resources in China.1. Background Coal is the main energy in China. Since entering the new century, China's coal industry has made significant progress, and the level of production safety, resource recovery rate and mining mechanization increased significantly, which provided a reliable energy supply for the rapid development of the national economy. However, due to the changes of China's economic environment, slow growth of energy demand and other factors, some prominent contradictions in the coal industry have significantly restricted the healthy development of the industry. The first problem is serious overcapacity. In the past few years, 16 industries including coal, electric power, chemical and others have invested in coal mines. It is reported (Han 2016) that only during the nine years from 2005 to 2014, the fixed assets of coal industry increased totally more than 3.3 trillion RMB, which brought a large number of production capacity. Affected by the slowdown of economic growth and energy structure adjustment, Chinese coal demand has reached the peak platform and caused the overcapacity of coal supply, so shutting down the backward capacity is the most important task in the future. The second problem is the low efficiency of coal production. There are about 4.3 million coal mine workers in China, and the annual coal production per capita is less than 900 tons, while it was reported (EIA 2016) that the annual production per capita in the United States is more than 10 thousand tons. The third problem is that the green coal resources are not rich. Among the 1.53 trillion tons proven reserves, only about one third are green coal resources in accordance with the principle of ""safety, technology, environment and economy"". The coal resources with high quality and easily mining conditions are not abundant."

Jan 1, 2017

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By Maria D. Mastalerz, Wei Wang, Maria E. Holuszko, Amit Kumar

In this study, the micro-FTIR analysis was used to investigate in-situ surface properties of coal and its components (macerals) and these were directly correlated to the coal hydrophobicity as measured by the contact angle before and after reagent addition to understand the suitability of the reagent for flotation. The micro-FTIR technique can provide a semi-quantitative analysis of the chemical functional groups on coal surface, exactly where the contact angle is being measured. Selected functional groups and their ratios that provide information about aromaticity, the contribution of oxygenated groups, and aliphaticity are used to evaluate the reactivity between reagents and various coal components. The observations made in relation to the susceptibility of some reagents towards certain coal components should lead the way to a smarter way of using process design in terms of reagents selection for coal flotation.

Jan 1, 2017

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017

By M. Savella

The Runruno Gold Project is located on the island of Luzon, approximately 200 km north of Manilla in the Philippines. The mine is a surface mine operation and use the proven BIOX® and carbon in leach processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces of gold, and the operation will produce 96,700 ounces of gold per annum over a mine life of 10.4 years. The BIOX® circuit is designed to treat 140,000 tpa of concentrate with a design capacity of 404 tpd of concentrate at a design sulphide sulphur grade of 17% S2-. The Runruno project is the first BIOX® plant to implement the Generation III BIOX® design principles. As part of the Generation III BIOX® program Outotec supplied a turnkey, containerised metallurgical laboratory to facilitate the first four stages of the BIOX® and ASTER™ inoculum build up requirements. BIOX® inoculum build-up was started during early January 2015 with 5 litres of stock cultures shipped from South Africa. The BIOX® culture was successfully adapted to concentrate produced from the mini plant during March 2015. The ASTER™ inoculum build-up commenced during early August 2015 utilising 27 litres of ASTER™ bacterial inoculum already adapted to similar process conditions expected during commercial operation. This paper will detail the various stages of inoculum build-up through to commissioning and ramp-up of the BIOX® and ASTER™ Processes at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX® design principles.

Jan 1, 2017

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

By Roberto Pena, Cristhian Morales, Darwin Morales, Veronica Cambiaso

"This article makes evident the shortcomings of the current operation of oxygen pipes as well as the damages they cause and why they cause them. When focusing on the causes and effects of these drawbacks, it was possible to develop a new family of thermal lances that could pierce a taphole with the precision of a drill but with the capacity to complete the whole operation. Although efforts have been made to replace oxygen pipes since they are annoying, dangerous and inefficient, nobody had worked to improve the way the traditional oxygen pipe taps/perforates the furnaces and reactors tapholes. In fact, developments made in drills and robotic arms, have failed to replace the oxygen pipe, which despite their negative side effects have been used for more than a century. Observation and theory were key to radically transform this humble tool into a dependable and efficient support in the operation. A good news that it is worthwhile to share for the benefit of all of us, passionate about the world of pyro metallurgy.INTRODUCTION Normally, reports and papers prepared for conventions, symposia or other technical events related to metallurgy aim to relevant topics in the operational field, probably because in them lay the scale economies every company pursues. We intend to give relevance to a matter normally disregarded in operations, but that unmistakably vital: if the furnace or reactor cannot be bled, the pyrometallurgical process will not be completed. Besides, if the tapping task is difficult or is long delayed, the availability of the furnace will be reduced. Consequently, there will be a waste of energy and workers will be exposed to dangerous levels of radiation as well as to work overload and physical injuries Apart from these basic effects, in tapping operations where oxygen pipes are used, we can see serious damages in the smelting furnace, especially in the taphole components such as refractory bricks, taphole jackets and water cooled plates. This paper intends to show that taking care of the tapping task can significantly upgrade not only to the tapping operation itself, but also the whole plant productivity."

Jan 1, 2017

By N. Dashbold, E. Rudnik

"Waste electric and electronic equipment currently comprises the fastest-growing waste stream in the world, but at the same time it is seen as an important source of metals for the recycling industry. E-waste is usually treated pyrometallurgically, with hydrometallurgical methods used to a lesser extent. This paper reports the results of research on the selective recovery of copper from smelted low-value electronic waste. Pyrometallurgical pretreatment of the scrap allowed the removal of plastics and the increase of metal content in the material. The obtained alloy of copper, zinc, tin and silver was a multiphase solid consisting of two brass phases and inclusions rich in iron, lead and silver. Copper alloy was further anodically dissolved in ammoniacal chloride solution. It resulted in high degradation of the material and accumulation of the metals mainly in the slime. The slime was then leached in acid or ammoniacal chloride and sulfate solutions followed by selective copper electrowinning. Hydrochloric acid was the most efficient solvent for the slime, but ammoniacal solutions were more selective for copper. Copper could be leached with 96 to 100 percent and 87 percent efficiency from the slime by the chloride and sulfate solutions, respectively. Copper with 90 to 99 percent purity at current efficiency of 42 to 76 percent was obtained from the acid solutions, while copper with 98 to 99 percent purity at current efficiency of 60 to 86 percent was deposited from the ammoniacal baths. IntroductionObsolete electrical and electronic equipment makes up the fastest-growing waste stream in the world (Baldé et al., 2015), due not only to the introduction of wider ranges of new types and models of a variety of electronic products but also to the shortening of their life-spans, sometimes referred to as planned obsolescence by producers (Keeble, 2013). About 42 million tons of electronic waste, or e-waste, are estimated to have been generated globally in 2014 (Baldé et al., 2015), and it is expected that in the European Union alone the waste electrical and electronic equipment (WEEE) stream will reach more than 12 million tons by 2020 (European Commission, 2015). Accurate evaluation of e-waste generation (Wang et al., 2013) and its global transport (Breivik et al., 2014) is difficult, mainly due to a lack of high-quality data related to its market and socio-economic dynamics.Many countries introduced legislation to control e-waste flow, collection and recycling. For example, Directive 2012/19/EU on waste electrical and electronic equipment (European Parliament and the Council of the European Union, 2012) obliges all E.U. members from 2016 to maintain a minimum collection rate of 45 percent of the total weight of WEEE collected. From 2019, the minimum collection rate to be achieved annually shall be 65 percent of the average weight of electronics placed on the domestic market in the three preceding years, or alternatively 85 percent of WEEE generated in the territory of the particular member."

Jan 1, 2017

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017