Search Documents

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By J. A. Delgadillo, C. A. Pérez-Alonso

"Tumbling mills using balls as grinding media are used extensively in the mining and cement industries to produce fine powders; however, it is well known that the process of size reduction is highly energy-intensive. For this reason, much of today’s comminution research is aimed at understanding grinding mechanisms, by estimating power draft and modeling milling circuits using the discrete element method (DEM). DEM predicts individual particle trajectories, the distribution of energy and contact forces at each collision, lifter wear and power draw. This paper presents a prediction of the discharge particle size distribution using three components, mass balance model (sometimes referred to as a population balance model, PBM), impact energy distribution of the mill obtained from the simulation of the charge motion using DEM and breakage characteristics of particles determined from drop-ball tests. DEM simulation of the charge of a tumbling mill was done using the code MinProSim 1.0 to obtain impact spectra at different operative conditions. Then, the population balance model (PBM), based on impact energy distribution, was used to predict the final particle size distribution in a batch mill and compared with experimental data. It is demonstrated that the DEM-PBM approach allows a reliable solution to predict particle size distribution for tumbling mills. Ideally, the model has to predict size distribution for any operational condition and feed characteristic; however, it has been shown that predictions include some degree of error.IntroductionThe discrete element method (DEM) has recently become a powerful numerical tool that can be used to investigate internal mill charge in ball mills. The early work of Cundall and Strack (1979) used DEM to analyze soil as a discrete medium. Later, the method was improved to simulate the operation of tumbling mills and optimize the design in order to increase the efficiency of energy utilization. Also, it is of great interest to relate ore breakage based on impact energy spectra obtained by DEM simulations and the breakage distribution function used in the PBM to predict particle size distribution in tumbling mills.King and Borgeous (1993) broke single particles in an ultra fast impact load cell to compute the phenomenological parameters in a microscopically more detailed population balance model. Kapur et al. (1997) simulated the size spectra of progeny particles produced by impact grinding as a function of the impact energy. Narayanan (1987), Narayanan and Whiten (1988) and Lira and Kavetsky (1990) estimated the energy-dependent breakage distribution function for scaleup and modeling of industrial ball mills."

Jan 1, 2015

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By G. Chahal, L. C. So, S. Faucher, S. Mostaghel, S. -Y. Oh, S. K. Lee

Slag dumping and water granulation are the most commonly used slag treatment methods in the metallurgical industries. In both processes, water is present (by desire for cooling and dispersion or as a result of rain accumulation) and thus equipment and operations are designed to minimize and mitigate the risk of steam explosions resulting from the inappropriate contact of slag with water. Slag handling practices have, therefore, never been inherently safe; even good design, operation, and maintenance are not sufficient to prevent explosions or other related injuries from occurring. For slag handling to become inherently safe, our industry must eliminate the potential contact of water with molten slag. This is today feasible with the advent of dry granulation technologies, a review of which is presented, and it thus falls to us, in the metallurgical sector, to lead the way in their final stages of development and adoption. Furthermore, while slag dumping and water granulation offer some metallurgists the means of valorizing their slag as a by-product, for most, this is not the case. The energy in slag is lost through dumping and water granulation processes, and where slag is sold as a by-product, it is for its chemical content only. Here, dry granulation processes also offer advantages including the production of by-products which hold value in both their chemical content and physical properties and heat recovery. Dry granulation, therefore, augments the methods by which slag may be valorized over traditional processing methods.

Jan 1, 2015

By S. Ndlovu, M. Malatse

"The Witwatersrand Basin is the heart of South Africa’a gold mining industry. The cluster of gold mines located in the Witwatersrand Basin generates a significant amount of mine tailings, which have adverse effects on the environment and ecological systems. In addition, disposal costs are very high. The exponential population growth in the Witwatersrand area has resulted in pressure on the reserves of traditional building materials. Quarrying for natural construction material is very expensive and damages the landscape. This work therefore examines the use of gold mine tailings in the production of bricks.Different mixing ratios of gold tailings, cement, and water were used. The resulting bricks were then cured in three different environments - sun dried, oven dried at 360°C, and cured in water for 24 hours. The bricks were then tested for unconfined compressive strength, water absorption, and weight loss. The results showed that the mixture with more cement than tailings had a compressive strength of approximately 530 kN/m2. It was also found that the best brick curing system was in a water environment. Bricks made from tailings cost more than conventional bricks because of the higher quantity of cement used, but the manufacturing process consumes less water. Overall, the results indicated that gold mine tailings have a high potential to substitute for the natural materials currently used in brickmaking.Paper written on project work carried out in partial fulfilment of BSc. Eng. (Metallurgyand Materials Sciences)"

Jan 1, 2015

By M. R. Julien

"The geomechanical behavior of rocksalt shows very distinctive features. The response of this most ductile of all low porosity rocks is dominated by inelastic processes that are strongly time- and historydependent. These characteristics must be taken into account when analyzing underground openings. Different constitutive models have been proposed and used for this purpose, and this paper presents the general formulation and applications of one of these. The SUVIC model relies on a unified approach with internal state variables producing mixed hardening to represent the inelastic behavior, which lead to specific solutions for plasticity and creep. The model equations have been implemented into a finite element code to perform numerical analyses. Simulations results are presented to show that this model captures essential aspects of rocksalt behavior under simple and complex laboratory testing conditions. Simulations are also conducted to analyze the response of underground openings. INTRODUCTIONPredicting the response of man-made excavations in rocksalt can be quite a challenge as it requires a reliable constitutive model to represent the material behavior. This softest of all low porosity rocks shows a highly non-linear inelastic behavior, very sensitive to history and rate effects (e.g. Senseny et al., 1993; Cristescu & Hunsche, 1997; Julien, 1999; Wittdke, 2014). The many deformation (micro) mechanisms acting locally in rocksalt make the construction of appropriate constitutive equations quite complex. Nonetheless, there have been significant progresses made over the last two decades or so; many of these developments have been included in a series of specialized Conferences Proceedings (Ghoreychi et al., 1996; Aubertin & Hardy, 1998; Cristescu et al., 2002; Wallner et al., 2007; Bérest et al., 2012)."

Jan 1, 2015

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By S. P. Pearton

"Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades, and their unique properties offer significant advantages in terms of improved safety, reliability, and performance. However, the benefits of pumpable emulsions have been unavailable to narrow-reef mining operations due to the lack of technology necessary for their successful implementation in this challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow-reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology, and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow-reef environment.The purpose of the following investigation was to evaluate the viability of pumpable emulsion explosives for use in South African narrow-reef mining operations. By approaching the problem from multiple perspectives, this research aimed firstly to propose a theoretical framework and suite of equipment suitable for the implementation of pumpable emulsions within the narrow-reef environment. Through the development of this suite of pumpable emulsion technology, tests could be undertaken on the proposed narrow-reef emulsion formulation and pumpable emulsion technology to obtain the necessary understanding of the performance of the system under controlled operating conditions prior to its implementation in the broader mining industry."

Jan 1, 2015

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By H. J. Oterdoom

SMS Group (SMSG) has always been concerned about safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and also SMSG contributed with its design features to a safer operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMSG wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2015

By Y. van der Grijp

The applicability of a stochastic approach to the simulation of gold distribution to assess the uncertainty of the associated mineralization is examined. A practical workflow for similar problems is proposed. Two different techniques are explored in this research: a Direct Sampling multi-point simulation algorithm is used for generating realizations of lithologies hosting the gold mineralization, and sequential Gaussian simulation is applied to generate multiple realizations of gold distributions within the host lithologies. A range of parameters in the Direct Sampling algorithm is investigated to arrive at good reproducibility of the patterns found in the training image. These findings are aimed at assisting in the choice of appropriate parameters when undertaking the simulation step. The resulting realizations are analysed in order to assess the combined uncertainty associated with the lithology and gold mineralization.

Jan 1, 2015

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015