Search Documents

By K. J. Ma, L. Ma, J. Stankus

The paper’s intent is to evaluate pumpable foamed cementitious mine seal material by determining the shear strength of a generic foamed cement in the laboratory. The tests were conducted on three scales: small-size specimens, consisting of cylinders 4 in. in diameter or 3-in. prisms; double shear medium- size specimens, measuring 13 in. by 10 in.; and large-size specimens, measuring 6 ft by 4 ft by 4 ft. The small-specimen shear tests resulted in average peak and residual shear strengths of 128 psi and 56 psi, respectively. These values are fairly consistent with published shear strengths of foamed cementitious material. However, the other two types of shear tests did not achieve the shear strength of a typical pumpable foamed cementitous mine seal material. Based on the test results, the paper concluded that the structural analysis of cement foam seals should be based on their residual shear strengths, approximately 20 psi, determined from small laboratory-scale tests of the cement foam/concrete or rock interface, and not be based on their peak strengths.

Jan 1, 2015

By C. S. Todd, R. L. McNearny, S. Dun, P. Clark, P. W. Conrad, X. Liu, J. Q. Wu, H. Rhee, W. J. Elliot

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining affects these properties is therefore important in developing effective management practices to control erosion during reclamation. To determine the impact of mining activities on soil hydraulic properties, soils from undisturbed areas, areas of roughly graded mine spoil, areas with replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated. Field and laboratory studies were conducted to determine the soil hydraulic properties of the four representative areas, including particle-size distribution, organic matter content and saturated hydraulic conductivity. Using this data, Water Erosion Prediction Project (WEPP) simulations and risk analyses were performed to investigate mining’s effects on changes in soil erosion potential. Significant differences were seen in the hydraulic properties of the soils in the representative areas due to the mining and reclamation practices at the mine. The WEPP simulations show that the potential for soil erosion increases as a result of mining activities disturbing the soil. The simulations also indicate that the erosion potential may return to pre-mining levels over time with effective revegetation practices.

Jan 1, 2015

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

By Y. Luo

Highwall mining, which is a relatively new mining method, is a preferred and often the only feasible method for extracting coal reserve left by surface mining operations in areas with steep terrain and in closely spaced thin coal seams. Though its safety record is comparable to that of surface mining, failures of mine structures in highwall mines, especially the highwall, have occurred. Methods for the systematic designing of highwall mines to meet the safety and operational challenges are still evolving. This paper presents the results of research into improving the existing design methods and developing new ones for highwall mining operations. The design methodology is aimed at ensuring structural stability of the highwall, roof, web and barrier pillars and preventing subsidence. It takes into consideration the major ground control challenges of soft and layered mine roofs, and interactions from mining closely spaced coal seams. An optimization design process applying a pressure arch concept can be incorporated to improve the recovery rate of coal reserve. A computer program based on the design methodology was developed.

Jan 1, 2015

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015

By Jorge Acosta Ale

El presente texto señala la dotación del cobre en el Perú desde el período 2013, la cual se encuentra ubicada en tres franjas metalogenéticas como son: Paleoceno, Eoceno-Oligoceno y Mioceno. Estas franjas produjeron más de 24 Mt de cobre y aún guardan reservas y recursos que llegan a 192 millones de toneladas. En ese sentido, el futuro de la producción de cobre se encuentra en 18 proyectos mineros, los cuales bajo un escenario optimista ingresan en producción entre 2014 y 2019. Para realizar este trabajo, se ha considerado datos estadísticos de producción global de cobre de la United States Geological Survey, y de la producción nacional de anuarios mineros del Ministerio de Energía y Minas el Perú hasta el año 2013. Los datos de reservas y recursos de operaciones y proyectos se han tomado de reportes anuales de compañías mineras y de exploración en el Perú.

Dec 1, 2014

By José De La Cruz

Para la construcción del dique de arranque de una planta concentradora es importante considerar la ingeniería y diseño del mismo -en tanto debe realizarse un diseño adecuado y así evitar problemas a largo plazo en la estabilidad de la presa de relaves. En ese sentido, el presente texto señala los costos, calidad y estabilidad del diseño de presas de relaves a través del proyecto de Toromocho S.A, perteneciente a la minera Chinalco, cuyo dique de arranque es CFRD (Concrete Face Rock File Design), método aguas abajo. La modalidad de este método permite diseños con un menor empleo de volúmenes de material de cantera que es aplicable en aquellas zonas con baja producción de material constructivo.

Dec 1, 2014

By Daniel I. Naupari Escobar

El presente texto señala las técnicas de campo empleadas en la mina Cobriza para el estudio base del sistema de ventilación desde el punto de vista psicrométrico, así como la evaluación del comportamiento termodinámico del sistema y las acciones realizadas para la mejora del mismo. Así también se realiza una introducción del análisis para la aplicación de sistemas de acondicionamiento de aire masivos.

Dec 1, 2014

By Iván Arana Sevallos

Dado que la mina Catalina Huancca posee rocas malas dentro de sus labores mineras, surge la inestabilidad de las mismas. En ese sentido, el presente texto señala la forma de aplicar la voladura controlada a través del uso de espaciadores inertes para espaciar los cartuchos de explosivo y reducir la presión que ejerce el explosivo en el taladro al momento de la explosión.

Dec 1, 2014

By Gregg Davidson, Lonnie Jacobs, Brett Zernich, Alan Howard, Robert Pintabona

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2014

By T Elkington, A Finch

The theory of constraints (TOC) is a business improvement method that focuses on exploiting a business’s bottleneck to deliver the highest possible profit. Early applications were mostly in the manufacturing industry; however, the theory in itself is completely generic and has now been applied widely in other industries such as services, retail, software and distribution, amongst others. The intent of the approach is attractive – it focuses on the ‘silver bullet’ rather than ‘death by a hundred projects’, and it focuses on growth rather than cost cutting. Application within the mining industry has been limited to date, although there are a few applications emerging. This paper discusses how TOC can be applied to maximise value during the project planning phase and how to maximise profits when the mine is operational. The paper uses two case studies to illustrate the approach. Case study 1 uses the approach to improve tactical mine planning, which delivers an increase in revenue of 58 per cent. The second case study is a strategic mine planning example that delivers an increase in value of 77 per cent.CITATION:Finch, A and Elkington, T, 2014. Application of the theory of constraints to strategic and tactical mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By P A. Grossman, J H. Rubinstein, M Brazil, K G. Sirinanda

To date, the scheduling and access design of an underground mine have only been considered as two separate optimisation problems. First, access to the mine is designed and then the scheduling is completed. One drawback of this approach is that the costs of access construction fail to be reflected in the net present value (NPV) calculation. In this paper, designing the access and scheduling its construction are formulated as a single optimisation problem.The underground mine access construction process can be classified according to the number of faces being developed concurrently. An underground mine with a single decline branching at a junction point into two declines is considered. After construction reaches the junction, the two faces of the decline can be constructed sequentially or concurrently.This paper proposes an efficient algorithm for optimally locating a junction point to maximise the NPV where two faces are being developed concurrently. The NPV is defined by taking the locations of orebodies and their values, decline construction costs, decline development rate and discount rate into account. The variation of the NPV and the optimal locations of the junction point for one and two concurrent development faces for a range of discount rates are discussed and compared. The proposed algorithm is applied in a simulated case study based on hypothetical values for an underground mine.CITATION:Sirinanda, K G, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Strategic underground mine access design to maximise the net present value, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By P Cesare, S Munro, D Wandel, R A. Bearman

Consideration of the processing plant operational envelope is a key factor in production scheduling,and therefore mine planning, for any mining operation. In many cases hard-wired or regressionbased tonnage-grade-recovery relationships are used as mine planning constraints and as a means of valuing the system output. In extensions of this type of approach, various regressions can be used to describe throughput limits, based on a number of global metallurgical parameters.The ultimate position for the optimisation of a mine plan and production schedule is to have a full process plant model running as an integrated part of the mine planning exercise. A plant model suitable for this needs to have all the required sensitivities to input parameters such asfragmentation, grade, mineralogy, strength and hardness. The model then needs to convert these to performance measures for the plant, which include recovery, throughput, product size distributions, energy consumption, water use and operating cost.In this paper an approach is outlined that takes this view and then goes beyond it to provide a full, time-based bottleneck identifi cation and valuation tool.Using such an approach it becomes possible to run mine plans and production schedules in windows of days, weeks, months and over the life-of-mine with a time-enabled process model acting as the active constraint. In this way virtual bottlenecks can be identifi ed for various mine plans and schedules well ahead of time. The value of de-bottlenecking can be defi ned, not just at a plant scale, but in terms of the overall mining operation, and the data can be used as the basis for capital investment decisions.CITATION:Bearman, R A, Cesare, P, Munro, S and Wandel, D, 2014. Incorporation of a full process plant model as an active constraint for mine planning and production scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M de Freitas Silva

One of the main steps during the decision-making process of long-term mine planning is the definition of the optimal sequence of extraction, which usually is synonymous with maximising the discounted cash flow of the project subjected to several constraints arising from aspects of technical, physical, and economic limits.Open pit mine production scheduling (OPMPS) comprises several intricacies related to its size and uncertainty of input parameters. Due to its complexity and prohibitive size, traditional mine planning usually relies on heuristic or metaheuristic methodologies which are able to provide good solutions in a reasonable amount of time. However, most of the uncertainty that surrounds the mining complex is ignored leading to non-realistic results.In this paper, a new heuristic approach is explored in order to solve a stochastic version of the OPMPS problem accounting for geological uncertainty in terms of metal content, multiple processing streams, and stockpiling option. The methodology involves generating an initial solution by solving a series of subproblems and this initial solution is improved using a network flow based algorithm.The algorithm was applied to a relatively large gold deposit with more than 119 thousands blocks. Results have shown that the methodology is promising to deal with large-size mine instances in reasonable time.CITATION:de Freitas Silva, M, 2014. Solving a large stochastic integer programming model for production scheduling at a gold mine with multiple processing streams and uncertain geology, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By T Wambeke, J Benndorf

A risk-robust development of a heavy mineral resource requires an assessment of the geological uncertainty and spatial variability of the key factors impacting the mining and processing operation. Attributes of interest are the total heavy mineral grade, the slime content and the amount of oversized particles. The modelling of a mineral sand deposit presents two main challenges. Firstly, the exact location of the geological boundaries are obscure due to the complex interaction of the deposit formation processes. Secondly, the properties of interest exhibit a rather complex transitional behaviour across the so-called soft boundaries. Traditionally, the modelling exercise is restricted to a consecutive stochastic simulation of distinct geological facies and orebody properties. This results in different zones separated by hard boundaries, ignoring the typical transitional behaviour.This contribution presents an alternative approach which models the entire sand body as a single domain while accounting for the complex trends present. Error curves are used to infer covariance model parameters without the need of a prior removal of the trend. The principle is based on minimising the differences between empirical and theoretical errors resulting from two methods of prediction calculated for different rings of influence. The added value results from the unambiguous decomposition of the spatial variation into a deterministic trend and a stochastic residual. The trend model neither overfits nor underfits the data. The calculated residuals are thus unbiased and the uncertainty can be correctly assessed.The effort results in a characterisation of the resource uncertainty which provides a more realistic image of the spatial variability of the key properties in and across the geological domains of an existing heavy mineral sand deposit.CITATION:Wambeke, T and Benndorf, J, 2014. Optimal inference of modelling parameters to simulate complex trends across soft boundaries – a case study in heavy mineral sands, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 73–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S Coward, C Xu, P A. Dowd

"This paper provides an assessment of the current challenges in strategic mine planning and design and suggested approaches for addressing them. The specific challenges covered are: realistic quantification of downstream processes applied to orebody models to provide an integrated approach to mine design and optimisation modelling, estimation and simulation of geometallurgical variables and their integration into resource and reserve estimation and mine planning modelling, estimation and simulation of new variables for new forms of mining – deep mining, particularly block caving, and solution mining flexibility in planning and design to manage risk and minimise its impact information technology (IT) infrastructure and platforms for rapid online data collection, storage, access and processing.Most of these challenges require new types of data, variables, modelling and estimation methods. Foremost among the new types of variables and data are geometallurgical and dynamic rock mass characterisation variables. New types of data and data collection include rapid generation of very large amounts of online sensor data and the consequent need for rapid processing and modelling of these data.This paper outlines the challenges and strategies in each of these areas and uses examples of models and outputs to illustrate approaches and potential solutions.CITATION:Dowd, P A, Xu, C and Coward, S, 2014. Strategies for mine planning and design, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014