Search Documents

By Jianhong Dong, Min Chen, Cuihuan Huang, Bo Li, Nan Wang

"Scale layer can be formed on the slab surface in the areas of secondary cooling and strand discharge during continuous casting process. From 1000 °C -1200 °C, the influence of steel composition on the stable oxide phases inside scale layer, particularly the types of alloying elements including aluminum, silicon and chromium, is investigated under different partial pressures of water vapor by the calculated predominance diagrams of iron oxide as well as its intermediate compounds formed with other metal oxides, and the stable oxide phase composition within scale layer under the working condition of secondary cooling is discussed. At lower partial pressure of water vapor, only a iron spinel (or ferrosilicate) phase is the stable phase with any alloying element contents in steel composition, whereas the stable phases are FeO and iron spine! (or ferrosilicate) inside the scale layer at higher partial pressures of water vapor .IntroductionOxide scale formation on the surface of cast and rolled products because of oxidation by the surrounding oxidizing atmosphere is a significant disturbance factor in steelmaking. The yield loss of iron because of scale formation is considerable during continuous casting and hot rolling process. Surface quality more often is impaired by scale property, which increasing the difficulty of quality assurance, dimensional accuracy and performance control. Furthermore, a potential source for subsequent surface cracking (hot shortness) can be caused by the enrichment of scrap residuals (Cu, As and Sn) at the steel substrate surface as a result of steel oxidation [1-2]. In flat products manufacture via thin slab casting technologies, these phenomena are particularly pronounced and require enhanced development efforts in descaling efficiency [3].Compared with the scale formation in continuous casting, the quantity of scale formed during hot rolling and reheating in the rolling mill is larger, and control of scale formation and descaling is a long-established task in hot rolling. Therefore, extensive research and development work have been carried out, including the effects of heating and rolling temperature on the thickness and microstructure of scale layer, heating time and furnace atmosphere, cooling mode, and steel composition on the scale formation, more attention has been given to the control of scale formation during reheating and hot-rolling process. On the other hand, hardly any specific efforts and countermeasures are taken in continuous casting, and very less research has been done despite the network-type crack on the as-cast strand surface caused by the subscale enrichment of scrap residuals [ 4-7]."

Jan 1, 2014

By P. Holtzhausen, L. Auret, B. Lindner, A. Haasbroek

"Spiral concentrators offer a cost effective way to separate valuable minerals from gangue by displacing lighter materials to the outside, and heavier materials to the inside of the spiral. The separation can be seen as visible concentrate bands and splitters are set at the bottom of the spiral to effectively split the ore into various densities. As there are typically many spirals in a concentrator plant, it becomes ineffective to continually adjust the splitter positions manually. Vermaak et al. (2008) proposed to use image recognition to detect the concentrate bands, thereafter, creating a model predicting the positions under certain input conditions. This model could then be used for optimisation and/or control of splitter position or band position. In contrast an online concentrate band detection system would provide real time concentrate band positions without losing accuracy due to model generalisation. These systems are usually expensive and time consuming to develop, due to a lot of centralised features required (image capturing, image processing and/or feedback to a controller). This study took advantage of the recently developed Raspberry Pi minicomputer to perform rapid prototyping of an online image processing sensor. The Raspberry Pi, and accompanying camera module, offers a portable Linux environment which can natively run the required image processing algorithms. Furthermore, extensive use of OpenCV was made to reduce development time, by relying on existing and proven algorithms to detect the concentrate bands. The Raspberry Pi also incorporates generic input/output ports which can be used in future work to provide the signal to a controller. In conclusion, the Raspberry Pi was successfully used to perform real time concentrate band position detection on a spiral concentrator. This solution is more general than an experimentally identified input-output model and may be used for control or optimisation studies in a wide array of spiral concentrators."

Jan 1, 2014

By Sabine Verryn, Johan de Villiers

"Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method however, requires a good initial calibration and periodic checks on its precision and accuracy.Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.1. IntroductionDiffraction of X-rays by matter has been used for more than 80 years, initially to elucidate the structure of crystalline matter, and to investigate the bonding between atoms. The first development of powder diffraction cameras and the later development of X-ray diffractometers saw the development of methods to identify phases and to try to quantify them in mixtures. A comprehensive database and search-match techniques have been developed over the ensuing years. Effective and accurate quantification had to wait for the so-called Rietveld' analysis where the total diffraction pattern is used and where the crystal structure data for the constituent phases are needed as input. Overlapping of diffraction peaks of different phases is handled without difficulty and reliable results can be obtained in spite of this occurrence.The development of methods for structure analysis from powder data has also progressed rapidly and more and more complex structures are being solved from first principles, i.e. without knowledge of unit cell or space group data. Because of the ease of use of the Rietveld method, it is finding increased application in metallurgy, especially in the quantification of phases of importance in minerals processing, in pyrometallurgical processes, and in materials characterization. This study will examine the principles of the Rietveld method, its application in metallurgy, and finally also the common pitfalls that need to be avoided.2. Rietve1d AnalysisAs the Rietveld method compares the experimental diffraction pattern with one calculated from known crystal structure data, the following data are needed:•,An XRD Pattern with as Iowa background as possible. This should have good resolution and high diffraction peak intensities. With modem X-ray detectors, this can be achieved in minutes rather than hours.•,Instrumental parameters such as goniometer radii and slit sizes are needed. These are the so-called ""Fundamental parameters"". They are used to calculate the shapes of the resultant diffraction peak profiles that are caused by the instrument. The parameters are used to correctly separate the instrumental effects on the diffraction pattern from the sample effects."

Jan 1, 2014

By Adam Powell, Matthew Earlam

INFINIUM, Inc. is scaling up a new molten salt electrolysis process for producing rare earth metals. Instead of conventional carbon anodes, this process uses Pure Oxygen Anodes™ which employ a stabilized zirconia solid electrolyte between the molten salt and anode. This eliminates two problems with today's rare earth metal production technology. First, it eliminates carbon anodes and contamination of the product by carbon and its impurities, enabling 10-100 times larger batch size than current practice, and lower labor costs. Second, it eliminates emissions of perfluorocarbons (PFC) such as CF4 and C2F6, which are very problematic greenhouse gases with 6000+ times the global warming potential of CO2. The zirconia also enables a sealed vessel with no LiF emissions, creates a reducing environment enabling use of low-cost welded steel vessels, and either produces a high-purity oxygen by-product or can use natural gas to reduce the necessary electrical energy with no HF production. This paper will describe the technology and its current status for rare earth metal production.

Jan 1, 2014

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

The present investigation aims to develop and distinguish mineral specific reagents with two functional groups for use in flotation of calcium containing minerals. For this purpose, a series of dicarboxylate-based surfactants with varying length between the carboxylate groups (one, two or three methylene groups) were synthesized. As reference, a surfactant with the same alkyl chain length but with only one carboxylate group in the polar part was synthesized. The adsorption behavior of these new reagents on pure apatite and calcite mineral surfaces was studied using Hallimond tube flotation, FTIR and ? potential measurements. The relation between the adsorption behavior of a given surfactant on a specific mineral surface and its molecular structure over a range of concentration and pH values, as well as the region of maximum recovery were established. It was found that one of the reagents, with a specific distance between the carboxylate groups, was much more selective for a particular mineral surface than the other homologues synthesized. This selective adsorption of a given surfactant to a particular mineral surface relative to other mineral surfaces as evidenced in flotation studies is substantiated by ? potential and infra-red spectroscopy data.

Jan 1, 2014

By S. H. He

This paper focuses on the influence of pulp oxygen content on the separation of pentlandite and pyrrhotite contained in two different process streams in the Clarabelle Mill, operated by VALE INCO. The two process streams are (i) the scavenger cleaner feed, the product of regrinding the thickened, scavenged concentrate and the B cleaned tail produced from treating the non-magnetic fraction of the milled run of mine ore, and (ii) the magnetic concentrate which is the magnetic fraction of the milled run of mine ore. In the Clarabelle Mill, sulphite (SO32-) and TETA (triethylenete-tramine) are together used to selectively depress pyrrhotite from pentlandite. These depressants pre-ferentially decompose collector and/or sulphur enriched species at the pyrrhotite surface, an appar-ently essential mechanism in pyrrhotite depression from the scavenger cleaner feed stream. Selectivity in depression may originate from differences in the electrochemical rest potential of pyrrhotite and pentlandite. As both minerals are susceptible to oxidation, aeration in conditioning and flotation plays a key role in selective flotation. Important differences in the flotation behavior of pentlandite and pyrrhotite from the magnetic concentrate and the scavenger cleaner streams are highlighted in

Jan 1, 2014

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

By J. Y. ` Xie

The paper introduced bio-oxidation plants of refractory gold concentrate in China and CCGRI cultures. CCGRI cultures are composed of bacteria and archaea. Archaea Ferroplasma acidiphilum is very thick and fills whole mineral surface. It plays a more dominant role in CCGRI process. Several years of practice has proved that the operating temperature in bioreactors between 38~52?,gold recovery is almost same. Pulp concentration has been increased each year and reached to 25%.

Jan 1, 2014

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By L. S. Zhou

HermesTM metal magnetic liner (MML) has been invented and manufactured by China Metallurgy and Mining General Co. (CMMC). This paper describes its mechanism, structure, magnetic field distribution, application, economic benefit and safety performance. The 10 years? service life in Benxi Steel?s Waitoushan Mine, along with 6 years? technological analysis on its application in 5500mm×8800mm (diameter × length) ball mill in Anshan Steel?s Diaojuntai mineral processing plant, has proved its advantages such as super reliability, long service life, light weight, thin thickness, low noise and short payback period. It has also demonstrated its positive effects on the grinding process such as high productivity, energy-effective performance and low consumption of grinding media. It reduces labour intensity and improves working conditions, due to its easy installation, free maintenance and the fact that it doesn?t require fastening bolts or cause slurry leakage. It is de-signed scientifically in accordance with the varieties of processing lines, mill specification, ore type and grinding media, and has been applied in different grinding processes for magnetite, hematite, gold ores, nonferrous ores and other materials. HermesTM MML has three types of products: General, Composite and Heavy-duty. They are designed to meet the requirements from customers in China and abroad. So far, more than 400 sets of MML have been applied in ball mills with diameter rang-ing from 1500mm to 5500mm. It has become highly popular in American market recently due to its safe and effective performance.

Jan 1, 2014

By Fathi Habashi

A new era in pressure hydrometallurgy is marked when the roasting - leaching - electrowinning process in the zinc industry was replaced by direct pressure leaching of zinc concentrate. Since then, the technology has received recognition as the technology of the future. Large autoclaves of unprecedented size have been manufactured and installed in a number of metallurgical plants for recovering copper and nickel from their concentrates or liberating gold from its refractory ores. An attempt to recover alumina from clay using pressure technology is underway. Autoclaves lined with acid resisting bricks or with titanium clad may weigh as much as 800 tonnes were transported successfully from the manufacturing workshop to the mine site over long distances.

Jan 1, 2014

By P. H. J. Mercier, M. Couillard

Aberration-corrected scanning transmission electron microscopy (STEM) allows for the nano-scale exploration of materials at unprecedented resolution and sensitivity. In this paper, we combine this approach with electron energy-loss spectroscopy (EELS) and energy dispersive X-ray spectroscopy (EDX) to analyze the carbon distribution in residual solids found in solvent-diluted bitumen product extracted from Alberta oil sands. Major components of these contaminant solids are ultrafine clays. Biwettable clays have been associated with the formation of solid-stabilized water-in-oil emulsion, which are known to increase the content of both water and mineral solids in the final bitumen product. We demonstrate that the residual solids present in bitumen product contain carbon intermixed with mineral particles of various size and shape. By probing the carbon content at the nanometer scale with the high chemical sensitivity of EELS, we provide direct evidence of carbon intermixing with clay platelets. This clay-organic association at the nanometer-scale will contribute to the biwettable, hydrophobic character of the platelets, and will therefore play a crucial role in the bitumen extraction process

Jan 1, 2014

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By Dario Libano

"The Line 5 Extension, in Sao Paulo, Brazil, is currently the most important investment in public transportation by Sao Paulo’s state government. It will connect the south part of the city to the city center, crossing through four other major Metro lines and stations; all currently in operation. The total extension of the line is 11 km (6.8 mi), and includes a new parking yard for the trains and 11 new stations. The Brooklin Station, one of the new stations due to be open and operating in 2016, has a unique geometry of five secant shafts.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One slurry wall, along the Santo Amaro Avenue, was to contain the contamination plumes, and another was for temporary support to enable the excavation of the shafts. The final retaining wall design was changed to a concrete structural diaphragm wall that reduced the construction time of the shafts by half, allowing the contractor to meet the construction schedule. This solution also avoided dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a hydromill was used in such a situation in Brazil. The hydromill, by overcutting the panels, increased the quality of the joints, and decreased the probability of having seepage into the shafts. The hydromill also created a seepage barrier and avoided movement of the contaminated plumes.The GeologyLocal geology is composed of a superficial Quaternary soil, basically soft organic clays and sands and gravels. From the depth of 8 m (26 ft) until 18 m (59 ft), geology is composed by tertiary medium compact sand with thin silt-clay layers. From 18 m (59 ft) down, there are alternations between compact silt-sands layers with very hard clays layers. Each is approximately 5 to 10 m (16.4 ft to 33 ft) thick.The Initial Basic DesignThe original basic design of the Brooklin Station was to be constructed from five 40 m (131 ft) diameter intersecting circular shafts, all in a line along the axis of the Metro tunnel, in 555 days. In the excavation sequence, the odd shafts were first excavated, waterproofed and had part of their inside cast-in-place structure built before the even shafts were excavated. During the excavation of the even shafts, part of the odd shaft’s support was demolished and connected with the even support. A 0.8 m (2.6 ft) thick plastic slurry wall, acting together with the wire mesh reinforced shotcrete support, ensured the excavation stability around the five shafts."

Jan 1, 2014