Search Documents

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

"The work in the paper introduces a 2-dimensional finite element model for analyzing particular material processing in a roller press. Two basic roller geometries are considered: (a) smooth rolls (used for milling and compaction) and (b) rolls with cavities, commonly used for briquetting. A model is presented that is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables.MODEL, RESULTS AND CONCLUSIONSAn associated Gurson model was employed as a constitutive model for the material. The calibration of the model was based on experimental results from an instrumented compaction die. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Powder River Basin sub bituminous coal fines with moisture content 9% was used as a model material.Two finite element models have been set up, one for the briquetting roll and one for the “equivalent” flat roll. Approximately 3200 plain strain continuum elements with reduced integration (CPE4R) were used. Lagrangian-Eulerian (ALE) approach in conjunction with judiciously applied remeshing was employed with the commercially-available, dynamic explicit version of ABAQUS finite element code.Comparison of model predictions with experiment shows that there is an agreement in terms of the general trends of experimental values recorded on laboratory roller presses. Gurson model overpredicts stresses at low densities and, as a consequence, overpredicts roll force and roll torque."

Jan 1, 2003

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached out with extraction of gold. For decreasing arsenic content in processed materials and for breaking up the lattice and opening up of gold the raw materials are roasted. Some regularity was established for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. This process allows minimizing the negative influence on the environment but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in fluid bed furnaces."

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a generic global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. As a point of departure we propose that it is not possible to place metals in the context of the sustainable development of society without paying due regard to the entire metals value chain. Thus, the starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions around the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions. The aim of these case studies is to highlight to the minerals processing and metals refining industries their potential role in a more sustainable global society.

Jan 1, 2003

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

By Sarah K. DeBono, Alan J. Monaghan, Emmanuel V. Manlapig, Gregory J. Harbort

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber."

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By Ponisseril Somasundaran, H-L. Chen, University of Athens, D. R. Nagaraj, Zhonghua Pan, Jing Wang

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By T Sprague, D Pateman

"The Gosowong Gold Project is owned and operated by PT Nusa Halmahera Minerals (PT NHM), an Indonesian company 75 per cent owned by Newcrest. It is located on Halmahera Island, in the North Maluku Province of the Republic of Indonesia, approximately 2450 km north-east of the national capital, Jakarta (Newcrest, 2017).Kencana is one of two underground gold and silver mines at the Gosowong Operation where ground conditions vary from competent to very poor. Development headings occurring in poor rock mass conditions require high capacity ground support including long tendon cable bolts. Manual installation of cable bolts in these development headings has been a time consuming process due to borehole collapse, blockages requiring subsequent re-drilling and a minimum eight hour grout curing time interval. The installation of cable bolts including the setting, plating and tensioning can impact the critical path for development heading advance resulting in development cycle delays.A review was conducted by PT NHM on current industry practices for alternatives to manual cable bolting. PT NHM subsequently approached Minova to assist with the development and trialling of self drilling anchors (SDAs) installed using jumbos with a rapid setting pumpable resin, CARBOTHIXTM. A series of system development trials were conducted and a reliable bolting system was developed utilising the existing jumbo drilling fleet with minimal required modifications.The system developed was a ‘one pass’ bolting process to install and grout SDAs using a two component resin with a remote, mechanised system. Improvements achieved from the system include: eliminating hole closure issues and more immediate support in poor rock mass effectively reducing personnel exposure to poor ground conditions by removing the requirement to access the drive backs reducing grout set time with full installation times for 6 m SDAs averaging 25 min.The resin grouting system has now been successfully implemented to effectively manage areas of poor ground conditions and to accelerate advance rates in high priority headings.CITATION:Pateman, D and Sprague, T, 2017. Development and implementation of a long tendon bolting system utilising resin grouting technology, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By B. W. Cavender

Capital investments are made for a variety of purposes, from providing incremental capacity at existing operations to developing and implementing new technologies intended to radically improve a company's capabilities. These projects generate very different business opportunities and create value in distinctive ways. For incremental improvements, the capital budgeting process assures at least a loose fit between short-term goals and readily available resources. However, the criteria used to evaluate capital projects often prevent a company from committing to more aggressive goals that lie beyond the firm's current abilities or resources. Such projects may not have clearly identifiable future cash flows, and the degree of interaction with other projects and the nature of the risk incurred may be difficult to estimate. Additionally, by focusing only on quantifiable benefits, the budgeting process often fails to recognize "soft" improvements such as increased operating flexibility or new knowledge generated by such projects. By rejecting these projects, the capital budgeting process may actually harm the company's future competitive position.

Jan 1, 1998

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By M. Carrales, C. J. Jirik, W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil , this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states . Information given on each heavy - oil deposit includes the following items : Field and formation , location , average or range of depth , average API gravity of oil , average thickness of formation , areal extent of field , total productive wells drilled in field , discovery date of field , field status in 1963 , cumulative production to Jan. 1 , 1964 , and all known types of secondary - recovery operations initiated ( active and terminated ) in the reservoirs . The geographical location of heavy oil accumulations in the United States is shown by a map , and a brief discussion of 14 different areas is given in the text . As of Jan. 1 , 1964 , 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place . It is also estimated that if the deposits which have had little or no production history , such as the one in Missouri , were included , the total remaining heavy oil in place would be in excess of 150 billion barrels . To find economical ways of recovering this vast reserve of heavy oil , industry is developing technology in several types of thermal - recovery methods . Some of the general considerations and more suitable limitations in selecting a prospect to study for thermal - recovery techniques are : Lithology , depth , viscosity of reservoir fluids , gravity of oil , reservoir thickness , oil in place , and permeability and porosity .

Jan 1, 1965

By R. H. Grau, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has investigated the unique ventilation requirements of large-opening mines to help identify and evaluate the effectiveness of various fan types to improve the ventilation and air quality in the underground workplace. Large-opening mines, with their low airflow resistance factors, can be ventilated with free-standing auxiliary fans because airflow pat-terns in these mines are primarily controlled by airflow momentum. The flow characteristics of both vane-axial and propeller fans were investigated and tested at four large-opening mines to assess the effects of fan location on recirculation and entrainment. Each fan type has its own airflow, entrainment and penetrating air-flow characteristics, and operating costs that are advantageous for specific applications. Either fan type can be used for most auxiliary applications. However, this research has shown that the optimum placement and use criteria for propeller fans differ from those promulgated by the U.S. Bureau of Mines (USBM) for vane-axial fans Brechtel et al. (1985)

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By S. G. Hardcastle, C. K. Kocsis

Ventilation is an expensive prerequisite for underground mining. Current mining trends, including increasing depth and mechanization and more stringent health regulations would generally dictate that more air volume is required in order to provide good working conditions underground. However, any increase in the mine’s intake airflow can produce a disproportionate increase in power consumption and hence operating costs due to the cubic relationship between the sup-plied air power and the airflow (Power a Flow3). Furthermore, forecasts of significant increase in energy prices and new commitments with regard to reductions of greenhouse gas(GHG) emissions, determined the mining industry to look into developing new concepts, design tools and incorporate the latest mining technologies in order to lower capital and operating costs while meeting commitments regarding GHG emissions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. A developing trend is to design and plan the mine by means of orebody modelling software, followed by using discrete-event simulation techniques to predict production rates and evaluate various operating scenarios throughout the life of the mine. The authors are currently evaluating how such process simulators could be adapted in order to forecast the need for materials or a specific resource, and one of these would be the mine’s “life-cycle” airflow demand as a function of scheduled production rates and mine operating characteristics. Further to this, based upon the mine’s life-cycle airflow demand schedule, the ventilation system could then be designed using a mine ventilation simulator. This new design approach would integrate in parallel the development of the ventilation system with the current mining conditions, therefore, heading towards “develop-as-you-go” as opposed to developing the system for final requirements with high upfront costs. This new ventilation system design criteria would also incorporate the use of the “ventilation-on-demand” technology, which will further lower development and production costs and implicitly, the mines’ GHG emissions.

Jan 1, 2004

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995