Search Documents

By R. M. Whyte

The complexities that exist in the nature of the basic feedstock to the metallurgical process call for a high degree of ingenuity from the extractive metallurgist in seeking the best possible treatment method for a particular ore. Drawing from personal experience the author presents four case studies that demonstrate the value of creative thinking in addressing the challenges typically encountered by the extraction metallurgist. It is concluded that creative expression most often occurs in response to a perceived strong need within an organization. By deliberately laying down meaningful challenges management can stimulate innovative thinking and achieve extraordinary results.

Jan 1, 2009

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

Jan 1, 1970

By Rejean Gagnon, Fernand Rochefort

"Haulage costs, in most operations, represent a large portion of total cost. Quebec Cartier Mining Company came to the conclusion t hat an electric trolley assist providing more horsepower than available from dieselgenerator sets presented the best oppor tunity for improvement. Accordingly, a testing and development program was carried out which resulted in the design, installat ion and application of a practical system. This paper describes the development of the system, the equipment used as well as the actual operation. A projection is also made to indicate further improvement in productivity. A comparison is made of truck operating data before and after activation of the trolley assist system in order to determine its economic impact."

Jan 1, 1972

By D. Sohn

Work accidents have an essential impact on the economy of a country and in final consequence on each company. The main purpose of industrial OHS is to maintain and promote the health of all employees. Healthy working conditions increase efficiency and motivation and safeguard the success of the business against the background of the extremely dynamic processes of change. Maintaining and promoting the health of all employees, weather in operation, administration or on the mining site, has become therefore not only an ethical requirement but also an economic must. Creating a suitable working environment for people today entails much more than just preventing accidents and work-related illnesses. It is important to be proactive in establishing an even better culture of prevention and to convince everyone, workers and managers alike, of its importance. Especially in the age of rapid changes and above all in view of global competition we are more dependent than ever on healthy, enthusiastic, competent and creative employees. OHS provides you with the necessary competitive edge.

Jan 1, 2007

Jan 1, 1967

By Jael Moutinho dos Santos

Em função do elevado consumo de corpos moedores de alto Cromo e do alto custo de sua fabricação com matéria prima nobre, busca-se o desenvolvimento de novas ligas de corpos moedores na busca de um melhor custo benefício. Devido ao efeito sinérgico do perfil de desgaste envolvendo fenômenos corrosivos e abrasivos em bolas de moinho, o desenvolvimento de novas ligas de ferro fundido branco alto cromo tem sido uma alternativa para suportar o desgaste precoce provocado por tais fenômenos. As amostras de corpos moedores, analisados mediante ensaio de análise química, dureza, análise micrográfica e seguidos de ensaios de moagem (úmido e seco), servirão a um desempenho comparativo para se designar a melhor liga a ser aplicada nos processos de moagem secundária de minério de ferro a úmido.

Oct 30, 2017

By Doris M. Hyde

The Bahama's petroleum-dominated minerals sector constricted again in 1985. The declines were mostly the result of a soft market demand for crude oil and petroleum products. In early 1984, it was a growing unprofitability that prompted Charter Oil Co. to cease using the 350,000-barrel-per-day Bahamas Oil Refining Co. facility that it jointly owns with Chevron Oil Bahamas Ltd. After midyear 1985, because of poor petroleum economics, Chevron announced it would close the refinery, leaving only a maintenance crew. In 1984, the refinery exported less than 26 million barrels of petroleum products. Chevron's throughput was reported as averaging about 8,000 barrels per day at the time of the announcement. The crude oil transshipment terminal also registered declining activity and financial losses in 1984 and 1985. Transshipments of petroleum in 1985 amounted to about 100,000 barrels per day, one-half as much as in 1982.

Jan 1, 1987

By K. M. Mayhew, G. D. Barr, T. M. McCoy, C. T. Knilans

"Teck Resources Limited (“Teck”) has developed and extensively tested on a continuous basis the CESL Technology hydrometallurgical process for treating copper and nickel sulphide concentrates, including bulk copper-nickel concentrates. Copper, nickel and cobalt are leached efficiently into solution, utilizing CESL process conditions. Total precious metals including gold, silver, platinum and palladium are recovered from the residue stream via sulphur flotation. This paper describes the CESL Technology testwork on a bulk copper-nickel concentrate derived from Twin Metals Minnesota?s (TMM) deposits within the Duluth complex and evaluates the economic benefits (increased cash flow, increased revenue certainty) and investment criteria (capital cost, payback and cash flow) of incorporating CESL Technology into the staged development of TMM?s deposits.INTRODUCTION Mineral Processing and the Role of Hydromet in the Duluth Complex The Duluth Complex in northern Minnesota, United States (US), represents one of the largest undeveloped accumulations of copper, nickel, gold, and platinum group metals (PGMs) in the world, ranking second in copper and PMs and third in accumulation of nickel. The figure below identifies some of the larger known deposits within the Complex (see Figure 1). Copper, nickel, PM and PGM mineralization within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex.One of the mineral processing challenges of Cu-Ni-PM-PGM deposits in this Complex is the complicated, polymetallic nature of the mineralization1: copper occurs primarily as chalcopyrite and cubanite with minor occurrence of talnakhite; nickel occurs as pentlandite and refractory nickel oxide/silicates; iron sulphides are present as both pyrrhotite and troilite; and PMs/PGMs occur in both the sulphide matrix as well as discrete minerals. An additional challenge for the Duluth Complex is the ratio between copper and nickel; in most of the identified deposits, copper grade is three to four times greater than the nickel grade, which precludes the production of a simple bulk concentrate due to the lack of a traditional smelting market for a bulk concentrate of this character."

Jan 1, 2017

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By P. Kim Carroll, D. Nick Tiffany, Doyl M. Fritz

Thunder Basin Coal Company received the 1987 Wyoming Excellence in Surface Mining Award for construction of the State's first major sediment control reservoir to be designed using the new settleable sol ids standard. Use of this standard resulted in construction cost savings of more than $250,000; reduced water quality monitoring; enhanced downstream channel stability because of more natural sediment loading; allowed simultaneous establishment of permanent waterfowl and fisheries habitat; and provided a quality recreational site. This article will address factors associated with the design and construction of that sediment reservoir and the benefits that were realized. (Note: This paper was originally published in the proceedings for the 1988 National Symposium on Mining, Hydro1ogy, Sedimentology and Reclamation held in Reno, Nevada, December 5-9, 1988.)

Jan 1, 1989

By AIME AIME

Award of a Gold Medal : to the Institute. The Jury of Awards of the Jamestown Ter-Centennial Exposition has conferred a gold medal, the highest distinction within its power,. on the American Institute of Mining Engineers for the excellence of its publications during the past decade. ; A half-tone photographic reproduction of both sides of the medal is given in the accompanying illustration.

Jan 7, 1908

By N. C. Trivedi

Natural calcium carbonate, commonly known as limestone is an abundant resource pretty much worldwide. Calcium carbonate occurs naturally as the main constituent of chalk, limestone, and marble. One of the unique characteristics of this abundant mineral is its versatility. Major markets for calcium carbonate are: paper, plastics, caulks and sealants, carpet backing, paint, and food additives. This broad spectrum of consuming industries has warranted producers of this industrial mineral to be innovative and quality focused simply to meet the ever increasing demands for performance. This need for improving performance of calcium carbonate has led to the development of new sources of calcium carbonate, natural as well as synthetic.

Jan 1, 2002

Technical disputes, commercial negotiations and workplace/societal conflict are a natural part of doing business and just living itself. Conflict is everywhere û at home (between family and neighbours); in the workplace (between management, co-workers and unions), with contractors and with other companies; and everywhere at the community level, dealing with land access (pastoralists/farmers and indigenous/First Nation people), environmental protestors and NIMBY-ites - Civil Society in general. Exploration and mining companies, operating in more remote, less developed and culturally diverse regions, tend to encounter myriad areas of conflict (typically emotion-charged) and they are outlined. Dispute prevention, management and various binding and non-binding resolution techniques are discussed. The paper gives a general overview of the ADR nomenclature and framework (mediation, conciliation, expert determination, adjudication, arbitration and litigation) encouraging technical professionals to participate. Its thesis is that lawyers should not necessarily be the first port of call when problems arise between the mining workforce, contractors, joint venture partners, purchasers of prospects/mines, traditional land owners, protest groups, etc. If the matter must be litigated, the role of the expert witness is critical in pretrial planning, negotiations, mediation and litigation management, so a few guidelines are provided. Whilst dispute resolution has a legal context, the paper is written from an AusIMM technical professionalÆs perspective, emphasising practical long-lasting pragmatic solutions.

Jan 1, 2006

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By Claudeir Carvalho Silveira

A necessidade da indústria automobilística de redução de peso, desenvolvimento de designs arrojados e aumento da resistência a corrosão dos automóveis obrigou as indústrias siderúrgicas a produzirem aços galvanizados de alta resistência. Entretanto, para que haja este desenvolvimento é necessário maior conhecimento do comportamento dos revestimentos galvanizados quando submetidos a processos de estampagem. Desgastes da superfície galvanizada, formação de pós, redução da resistência a corrosão e atrito das superfícies são aspectos importantes a considerar no projeto do ferramental de estampagem. Este trabalho teve, portanto, como objetivo a avaliação do efeito dos revestimentos Galvanizing e Galvannealed no coeficiente de atrito de um aço Dual Phase 600. Para avaliação do coeficiente de atrito foi utilizado um tribômetro de ferramenta plana que simula o atrito na estampagem de peças. O trabalho apresenta ainda a caracterização microestrutural do revestimento realizada por microscopia ótica (MO) e eletrônica de varredura (MEV) e espectroscopia de energia dispersiva (EDS). Para avaliação das propriedades do substrato e do revestimento foram utilizadas também medidas de Microdureza. Após a realização dos ensaios, foi caracterizada ainda a evolução dos revestimentos após desgaste promovido pelo tribômetro de ferramenta plana e a identificação e caracterização do fenômeno de stick-slip.

Aug 8, 2018

By W J. Rankin, D R. Swinbourne

There are large tonnages of low-grade manganese ores in India fromwhich it is uneconomic to produce ferroalloys by conventionalsubmerged arc furnace smelting. A possible way to utilise these ores is to smelt them with carbon to produce pig iron and a manganese-rich slag, then to metallothermically reduce the molten slag to silicomanganese. Thermodynamic modelling of the metallothermic reduction stage using aluminium, silicon or aluminium-silicon alloy as the reductant at 1450¦C showed that an acceptable grade of silicomanganese could be produced. Manganese recoveries were predicted to be about 80 per cent. Heat balances indicated that silicothermic reduction may not produce enough heat to maintain reaction temperature. Small-scale laboratory experiments showed that the manganese grade of the alloys, and the manganese recoveries, were close to those predicted, but those for silicon were muchlower. Aluminothermic reduction produced the highest grade manganesealloy. The slag-metal equilibrium involving manganese, silicon and their oxides was investigated and it was found that equilibrium was not attained in any of the experiments, due probably to the very low rate of reactions involving silicon. This could be used to advantage in practice to achieve higher manganese levels in the alloys.

Jan 1, 1998

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By F. Nelson

RJB Mining is the largest coal producer in the UK. In January 1995 the Company acquired the Central North and Central South Regions of British Coal consisting of: ? 15 operating collieries -including capital equipment ? 2 care and maintenance mines ? 16 operating Opencast sites ? Interest in 26 prospective and 46 potential Opencast sites ? Approximately 417 million tonnes of proven and probable reserves and considerable mineral resource ? 9 million tonnes of coal stocks ? Long term contracts to supply approximately 90 million tonnes of coal to National Power and PowerGen to the period of 3 March 1998 ?Approximately 7,600 employees and 4,500 mining contractual labour. Up to the acquisition RJB Mining had the capacity to produce 14 million tonnes of saleable output with an approximate 1,500 strong workforce.

Jan 1, 1998