Search Documents

By M. D. Mwema

Copper oxide ores deposits in the Katanga province of the Democratic Republic of Congo (DRC) contain at variable level cobalt oxide minerals. In contrast to copper oxide minerals which readily dissolve in the sulphuric acid solution, the cobalt oxide bearings are difficult to dissolve, especially if cobalt is present in the third oxidation state (Co2O3). This species become soluble after reduction of Co+3in Co+2. In practice, the use of reducing agent is therefore necessary in order to transform the insoluble minerals into soluble cobalt sulphate species. The following reducing agents are currently used at the Shituru plant: ferrous ions, which are present in leach solutions, pulverised copper or sodium meta bisulphite (MBS). Due to the high consumption of reducing agents (0,8 t MBS/t of solubilized Co; 1,2 t Cu/t-Co), cobalt production is expensive. The use of sulphur dioxide as reducing agent was then investigated in order to reduce operating cost. This reagent also presents the advantage of sulphuric acid production during the leaching process. It has been added in the leaching vessel (tank). From the laboratory and industrial tests, selective leaching of cobalt (78%) has been performed. The cobalt leaching kinetic depend on sulphur dioxide dosage. Dissolution of copper, iron and manganese remained very low. No emanation of SO2 gas was observed during the process.

Jan 1, 2002

By C. B. Manula

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a Southwestern surface mine using draglines and front-end loaders is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and to analyze alternatives for increased production. The simulator was verified by comparing long term production figures to the simulated results from data collected on a mine visit. A short term and a long term alternative are studied with projected productivities and scheduling. No economic analysis of these proposals were performed.

Jan 1, 1977

Past issues of Minerals and Materials have discussed such aspects of the economy as consumption and investment expenditures, interest rates, productivity, and international trade barriers and their effect on the minerals industry here and abroad. In this issue, we will (l) look at recent indications of a possible economic recovery, (2) present 1983 expectations reflecting the results of industry surveys conducted by the U.S. Department of Commerce (DOC), and (3) briefly discuss the contribution of the U.S. mining industry to total gross national product (GNP). THE RECOVERY Throughout most of 1982, DOC's Composite Index of Leading Indicators provided evidence of impending improvement in the economy. The index increased moderately during eight of the months in 1982 and then jumped an estimated 3.6 percent in January 1983 (table 1). While the leading indicators continued to predict improvement, the general economy, as measured by the Index of Industrial Production, continued its slide through November 1982 (table 2). Finally total industrial production increased in December 1982 and continued on an upward path in January and February, as predicted by the leading indicators.

Jan 1, 1983

By D François-Bongarçon

After a review of the progresses made on the liberation factor theory since its inception by Gy (1982), a new and surprising result of great practical importance is presented: the liberation factor. First introduced simply as a number between 0 and 1, then shown to be the ratio of two variances, is now shown to be well approximated by the proportion of liberated mineral.CITATION:François-Bongarçon, D, 2017. Evolution of the concept of the liberation factor and a surprising new result, in Proceedings Eighth World Conference on Sampling and Blending , pp 307–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The Phoenix mine on the Mararoa Reef at Norseman, Western Australia, provides an outstanding: AUstralian instance of the recurrence of payable ore beneath the bottom of an abandoned mine, and an interesting and instructive example of the development ofideas with regard to ore recurrence in a particular district. The Mararoa Reef is the most productive of several hypothermal goldquartz vains in pre-Cambrian basic volc81olics which strike northsouth and dip on the average, 45 degrees east. The Phoenix minewas abandoned at 500 ft. vertical depth after producing 342,000 tons of 9.9 dwt. recovery grade (equivalent to nearly half of the total production of the Norseman field) from a 2,500 ft.. long, horizontally disposed oreshoot, which is reported to have had an ore outcrop only 30 ft. in length.Interest in the field was revived in 1933, and by 1941 new ore mined and developed on the Mararoa Reef by Central Norseman Gold Corporation N.L. amounted to approximately 700,000 tons of 6.7 dwt. recovery grade. In the same period another oreshoot of similar size and grade was developed by Norseman Gold Mines N.L., south of the old Mararoa company's site. As shown by the plans, the ore occurs in discontinuous shoots. The intervening area of shear is poor in quartz as well as in gold. Geological work on behalf of Western Mining Corporation Ltd., and Central Norseman Gold Corporation N.L. has been in progress in the mine and in the field more or less continuously from 1913 to 1941 and again since 1946. This paper describes the successive advances in the understanding of the exploratory problem up to late 1941, to which several investigators have contributed. It is published by permission of the Board of Directors of Central Norseman Gold Corporation N.L., owners and operators of the Phoenix and other mines.Development of the Prospect.In 1933 Western Mining Corporation acquired an option over the Phoenix property and adjacent leases. H. E. McKinstryl visited the mine and recognised that the ore occurred primarily on the flatly dipping sections of the vein, as distinct from the steeply dippingsections, in a wide shear zone with reverse movement. Many of the flatly dipping fractures were seen to exhibit tension phenomena and to link one shear plane to the next below on the footwall side. The flat links carried much more quartz than the steeper shears.Later, H. J. C. Conolly, assisted by J. D. Campbell, examined the prospect and by contouring the vein with reference to an inclined...

Jan 1, 1950

By W. H. Yarroll Discussion by W. A. Griffith

W. A. Griffith (Head, Research Department, Phelps Dodge Corp., Morenci, Ariz.) - It is gratifying to see the increasingly common use of classical statistical procedures by metallurgical researchers. Mr. Yarroll has given excellent illustrations of the utility of multiple correlation analysis of complex metallurgical data. Our experience in applying these procedures to historical plant operating data has differed, however, from that which he suggests. The uninitiated frequently assume that the volumi-

Jan 1, 1969

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By D. G. Foot

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2 pct K20, and recoveries from 84 to 99 pct. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97 pct of the potash in a concentrate containing 54.3 to 60.3 pct K20. Fatty acid flotation of the high-sulfate evaporite recovered 78 pct of the sulfate minerals in a 27.8-pct-K20 concentrate. Flotation of the chloride minerals with amine collector recovered 80 pct of the potash in a 59.7-pct-K20 concentrate. Solar evaporation of 10,000 gal of brine recovered 99 pct of the potash in a crude evaporite containing 24.5 pct schoenite and 20 pct sylvite. Continuous flotation in a 100-lb/h process research unit recovered over 95 pct of the potash in schoenite and sylvite concentrates containing 28.0 and 62.3 pct K20, respectively. An economic evaluation suggested a rate of return of 3 pct for a new facility and 9 pct if. the process is adapted to fit an existing plant.

Jan 1, 1984

By M. C. Makepeace

"It is the objective of designed experiments to obtain more information for less material and process cost than can be obtained by traditional experimentation. In this paper, the fundamental concepts on which the statistical design of experiments is based are briefly re-viewed according to the following outline: The Experiment The Design The Analysis Two simple 2"" factorial experiments are presented as examples."

Jan 1, 1967

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson's chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

By M. A. Reyes, L. Yan

Heat and humidity buildup withn refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a lifesustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ.

By R. S. Dean

[During the past fiscal year the Metallurgical Division has made important contributions along the lines dictated by the Bureau policy of conservation of domestic mineral resources through Its investigations include determining of fundamental data of metallurgically important materials improvement of standard ore-treatment method to eliminate waste and improve the grade or recovery of the products; and development o new metallurgical processes.]

Jan 1, 1940

By R. S. Dewey

The purpose of this study was to assess the various aspects of public safety related to the thousands of abandoned or inactive underground mines found throughout Western Colorado. Review of available published mine inventories yielded data on over 8,000 abandoned underground mines. A random sample of 200 mines was then selected for field visits representative of mining activity in Colorado. Inspections of the openings at two hundred abandoned underground mines were performed recording descriptive information regarding the opening, the mine site, the surrounding area, the primary opening hazard, secondary hazards related to structures or dumps, other openings to the same mi ne, available construction materials, possible safeguard methods, and any special observations such as apparent activity, previous closure attempts, environmental constraints on construction, and access problems. Of the 200 mines visited, twenty mine openings representative of varying geologic, environ-mental, access, and mining conditions were selected for detailed low-cost safeguard application. Description of these safeguards is presented in narrative, itemized labor-materials equipment tabulations, and illustrations. Research into the regulations of mine closure and safeguards was also undertaken to determine jurisdiction of public lands. Recommendations were suggested to improve the awareness and ability to continue this program into an implementation stage.

Jan 1, 1980

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By Arnold O. Tanner

Tables based on 1985 data, which were not available in time for publication of the "1985 Minerals Yearbook," are included in this chapter; corresponding tables for 1986 are not yet available. Raw nonfuel minerals produced in the United States during 1986 had an estimated value of $23.5 billion, an increase of $0.25 billion over the 1985 value. This is the fourth consecutive year that the value has increased, and except for a de- crease in 1982, the value each year has increased since 1971, or 14 out of 15 years. Industrial minerals growth slowed from a 3% increase in value in 1985 to a 1.5% increase in 1986, reflecting the slow growth in the domestic economy. The value of industrial minerals, more than three times larger than the value of metals, easily offset the less than 0.5% decline in the value of metal mine production. Although the decline was small, this decrease makes 1986 the fourth year in the past 6 years in which a drop in the value of metal mining production occurred in the United States. U.S. production continued to lag behind the growing world production. Overall, the estimated raw nonfuel mineral production rose 1% over that of 1985. Domestic mine production of ferrous metals declined as follows, in decreasing order of production: nickel, iron ore, tungsten, and molybdenum. All remaining domestic primary nickel and tungsten mines had closed down by yearend. Nonferrous metals that similarly declined included titanium, rare-earth metals, lead, silver, zinc, and magnesium. For the second consecutive year, aluminum, produced predominantly from imported bauxite, declined in production, while imports reached record-high levels. Somewhat modest gains were made in beryllium and copper. As has been the case for a number of years, gold was a bright spot in the domestic and internation-al metal mining industry. Gold production was spurred on by the increasing usage and development of heapleaching techniques that make lower grade ores, which were previously uneconomical, profitable. Additionally, various mining companies, the U.S. Mint, individual States, and a number of foreign countries began production of gold bullion and commemorative coins. Gold output in the United States increased from 2.43 million troy ounces (revised) in 1985 to about 3.73 million troy ounces in 1986, a dramatic 54% rise.

Jan 1, 1988

By AIME AIME

T HE 121st meeting of the Institute held in New York City, February 16 to 19, 1920, was a great success despite vicissitudes of weather of unusual severity. On account of tremendous snowstorms, only two members of the Canadian contingent arrived, and several of our members from the west arrived thirty hours late. Two weeks prior to the meeting, the heaviest snowstorm in 34 years wrecked the surface transportation in New York; and it was only by special dispensation that arrangements were effected, with the New York Street Cleaning Department to clear away 39th street in front of this building so that vehicles could reach the curb. The total registration of members and guests was 1138.

Jan 1, 1920

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By D. E. Van Dillen

Three-dimensional structural analyses of three instrumented areas of a deep, longwall coal mine have been performed using the finite element code BMINES. The three Instrumented areas include two single-entry portions and one double-entry portion of the Sunnyside No. 1 Mine, Sunnyside, Utah. The finite element models simulated the sequence of excavation in each test area: the advance of the entry, installation of structural supports, retreat of the longwall, caving behind the longwall, and accumulation and loading of the gob. The structural supports considered in these finite element models include rock bolts, wood cribs, concrete cribs, steel arch sets, and chocks. Mechanical simulation of the geologic environment is achieved through elastic/ perfectly plastic material models employing anisotropy to represent finely layered regions of the medium. The results of these calculations are com-pared with the instrumentation readings from the mine. These measurements include closures, crib loads, rock-bolt forces, and stress growth.

Jan 1, 1978

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000