Search Documents

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

By Dhanesh Chandra

[The U.S. Ucparunent of tlIe III LeriOr, Bureau of 1?Ilnes, lnta dcvcltil- (I a m.?tl,nd to extract nickel, i:ob.tll and IlIIicr Valuc:l,1, mrl?tl., lrom I.ow grad:, dumusI it Inlet itc.: :isin;; a rarb-i mnnnxid:: reducl.iun and ,innnonln/mumonlum sull,h.Ito Icitcll Col lowed by solved. evil let foil and clot tr:,winnfu,;. 'I 'o rain bcLtur undcI'sLandin;; uI the producLs reduced rind leached with the s;:Item, the liureau of t?Ilite; was enf,ngod In a 1 uinL sl.utly IIt1I the Uuttvcr ltc~:c:n-ch LnstiI-IL-. 'I'hr'ut;;h C(Im:drlod ahplit I¬L ion:; of a rotnbIW)L11nl ill eleu Lyon :utJ uplical inicrnscopy, cle trun beau micru,inal?;st?s and X-r.iv tcchnitlaes, Lhc factors jilt] ucncing low nickul e::lracl.on yLrids Iron, ccrlnin l;tteritos wul the hcuefhe al yCferL front addil.I:un u1. r:u)plowt' ruug,ounus and halides have bucn rrvealod. IL leas ht'en shown their nt nliJcrate Lion terlperuLuri's (5S0°C - 6501C) Lhe 111LACl extraction ylolds were low hccausc of the futmetlt-m of rufrill t,urv sillc:Ite compicxcs during ciii lit Hi [hut COOL.tlu sig nlficnnt anutunls of nickel .Lrui LhaL arc resistant Lu discolullull it, a su6r.C?quent ammnnlIca1 Jcaeh. 'This formation ill rulracLorv rnngtieves is altrlbuU?d Lo the prc.srnCV of aluauinum combined with c.ilicun jn addlt.lon In tnnl;neni~im in I.lic Lalerites, Iligb exII.Ictlon yields were oblalneJ when none or only a few I ,fraCLot' e, were InrmeJ. Hit s;intc rcfrarlnry cowl, Icxc5 also lend Lo surround Ow IaaIIiable meI.allle iron-IIIcI:el :iILoy CIUSisling ill the mau'ix, tIll: rrhv nreveu)Ling cuntacr ,Itlt LI5U Jeacl: solution; this, huwrvcr, ran ho ovu:rcoml by At ti itlon .111.11 retieCtiun. 'I'hc eIIcc l of prr.reJIctlun .,Ill itivi's vucli i's lye iii', ',udlum "Ill orIde, hv,Irogrn CIIInrILIC, etc., and Lht? 1111,Lre:InrLlI'll he'e:tleg un Lbe cxLt,icLitin are also iilsr.ussod 111 Lhe rcl,olt.]

Jan 1, 1979

Jan 1, 1967

By J. Galloway, P. K. Hofmeyr

Obviously all mining operations require much analytical work to be carried out. This starts with exploration, becomes more stringent with the evaluation of a mineralised area and finally becomes on-going when mining operations are under way. All these phases are carried out by geologists, metallurgists and mining engineers. They require analyses to carry out their functions but usually have no involvement in the analyses themselves. Analyses are carried out at commercial laboratories or in-house analytical laboratories. In the past in South Africa the tendency was for the larger mining houses to have their own centralised laboratories for exploration samples with each mine having it?s own laboratory to meet only that mine?s requirements. The centralised laboratory maintains QC functions at the subsidiary laboratories. In other mining areas of the world there has been a strong tendency for all geological analytical requirements, especially for exploration and mining, to be carried out at commercial analytical laboratories. In recent years there has been a tendency for mines in South Africa to move in the same direction. This paper discusses the factors that need to be taken into consideration when a new laboratory is being planned and automation is an option. The planning of the laboratory at the new Langer Heinrich Uranium mine in Namibia is discussed considering these factors. 2.0 REQUIREMENTS OF A MINING ANALYTICAL LABORATORY The purpose and requirements of a mining analytical laboratory are fairly obvious and can be summarised as follows :- 1. All mining operations must have access to analytical facilities, either in-house or commercial 2. The laboratory must be able to handle all the sample types submitted by the mining operation These can be mining, exploration and/or plant samples. They can comprise solids (rocks, bore-cores), slurries and/or liquids.

Jan 1, 2007

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By Heitor Cristo Clem de Oliveira

O objetivo deste trabalho é estudar a reação de dessulfuração, envolvidas no processo de pré-tratamento de ferro-gusa. A princípio, as misturas utilizadas foram caracterizadas e estudadas através do software de termodinâmica computacional (FactSage 7.1). Em seguida, os resultados obtidos através do estudo termodinâmico computacional foram comparados com aqueles obtidos mediante os testes experimentais a 1400°C. As misturas dessulfurantes tiveram como base a CaO com três tipos de fundentes, fluorita, sodalita e barrilha, além da utilização de alumínio como elemento desoxidante. Os testes experimentais permitiram identificar que a adição de 0,1% em massa de alumínio no gusa, eleva a taxa de remoção de enxofre principalmente no instantes iniciais do processo. Com a utilização da termodinâmica computacional pode-se mostrar que a reação de dessulfuração no ferro-gusa é exotérmica para os teores de silício encontrados no processo. Além disso, a termodinâmica computacional também contribui, em alguns casos, para a análise de compostos sólidos que podem se formar na escória e limitar as reações de dessulfuração.

Oct 30, 2017

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By Nan C. Jensen

Silica, the world's most abundant mineral compound, is composed of the two commonest elements - oxygen and silicon. In addition to being the life-giving constituent of the atmosphere and the major element in the waters of the earth, oxygen comprises almost half of all known terrestrial matter and occurs combined with most of the other ninety-odd elements in the solid crust of the earth; however, a large proportion of the oxygen is combined with silicon. Silicon is second only to oxygen in abundance in nature and constitutes more than one-fourth of all known terrestrial matter. The compound of oxygen and silicon, called silicon dioxide or silica, forms 59.08 percent of the earth's outer 10-mile crust. Some of the silicon dioxide exists as

Jan 1, 1942

By Jeff Peterson, Alastair Grogan

During the winter of 2001/2002, a number of seismic exploration projects were carried out in the Mackenzie River Delta area of the Northwest Territories, in Canada. The purpose of the seismic projects was to identify potential drilling targets for subsequent drilling programs, using explosives as a seismic source. Recent changes to fisheries regulations meant that blasting under lakes, the Mackenzie River and offshore from the delta, was not allowed to induce water overpressures in excess of 100 kPa in these water bodies, and that a water overpressure monitoring program had to be conducted to confirm that this requirement was being met. This paper describes the water overpressure monitoring program on one of the exploration projects, presents the results of the monitoring, and discusses the challenges of carrying out this work in the middle of an arctic winter.

Jan 1, 2003

By A. Peake

Background The CSIR Division of Mining Technology assumed responsibility for the operations of the Hoist Rope and Mechanical Test Laboratories at Cottesloe in April 1999. The laboratories were previously the responsibility of the CSIR’s Division of Manufacturing and Materials Technology, before which they fell under the National Mechanical Engineering Research Institute (also of CSIR). As the focus of this conference is on safety in mines research institutes, it was thought appropriate that this paper should review some of the activities at Cottesloe and its role in supporting mine safety strategies.

Jan 1, 2003

By N. S. Kim

Silver paste including nano sized particles maintains conductivity in high temperatures without forming oxide layers. In the industry, printing process produces wasted silver paste inside the cylinder and on silk-screen. Pyrometallugical silver recycling methods have environmental problems and do not extract pure silver after removing polymer and organic materials during the extraction process. In this study a simple wet process, of recycling the waste silver paste, using ammonia, was conducted. Silver ion extraction yield was increased using oxidant in the ammonia solution. Possible extraction yields, such as pH, concentration, temperature of ammonia, oxidant concentration and the extraction time. The particles that were obtained after the extraction process will be used as porous hydrophobic catalytic and applied to AI mask and hydrophobic ink. Keywords: Waste silver paste; Ammonia; Hydrophobic porous support

Jan 1, 2009

By J. Hebert, J. Donnelli, J. Sedey

Installation of a Load Commutated Inverter (LCI) provides an economical method for conversion of a Fixed Speed Semi-Autogenous Grinding Mill into one with variable speed, qualities. Though capital intensive, the conversion appears to be one of the most cost-effective methods to gain the advantage of critical speed variations for variable ore characteristics. Expected advantages from the installation of LCI drives at the Goldstrike Mine were decreased liner wear, decreased media consumption and additional grind for increased production rates. These issues as well as construction, economics and performance will be discussed in the presentation. The utilization of the existing equipment came to play an integral part of the study and economic justification of the overall project.

Jan 1, 1999

By Kenneth Eilerts

[Efficient and econonic production of ?etroleum requiros knowledge of the propertios of rescrvoir fluids a:$. their characterintics of flow throayh porous forclntions. The cllanga in propertie s and flow characteri s- tics of fluids when their corosition is altercd cs a rnsult of reservoir- pressure decliae is of 'mecial i~ortenct? ir, planning wall-spaAng pro.yama and production schedules. Rct~ntion of the ~eatent poscible quantity of dissolved gac in the rescrvoir liquid gnneml'y is recognized cs ess~ntisl to mxim ultimzte recoverj of oil fro3 the underground reecrvoir. Ilo:rever, pro6uction mothodn tending to mintain gis in solution in the oil and re- sulting in the optimm ocolo~ic recgvery of oil not only vary from field to fiold but also my have to be changed from time to time in a given field as it is being depleted of its recoveraklo oil. Const vestly there is need tc investigztc tY.e propertiec of resa:-voir f kids corresponding to successivc stages of reservoir depleJ&ion with the view of obtnining infomation oacential to efficient prcriuctian practices.]

Jan 1, 1939

By Janaina Gonçalves Maria da Silva Machado, Carlos Mateus Braga de Almeidar, Leandro Miranda Nascimento

Knowing the reduction of the concentration of iron in the mineral load extracted in the last decades and, therefore, greater need for comminution processes, there is no denying that iron ores tend to get increasingly thin for steelmakers. In Reactors such as Blast Furnace and others of fusion-reduction, where the reduction of the iron ore for the metallic iron for the steel production occurs, we observed that one of the alternatives is to agglomerate the raw materials in the form of briquettes, improving the kinetics of the chemical reactions, since ores in the form of fines impair factors such as the permeability required for reduction. These agglomerates are composed of a reducer, fines of ferrous materials and a binder material, and require, in addition to satisfactory Metallization, mechanical resistance, avoiding losses when the compound is fragmented during transport or during its deposition in the Steel Reactor. In the following work, Briquettes were produced with Charcoal, Pellet Feed, Molasses Cane and Hydrated Lime. The mixtures were pressed under different conditions of Pressure (1, 2 and 3 tons-force), and pressing time (20 , 60 and 100 seconds), aiming to analyze the influence of these two variables on the drop tests, mechanical resistance of the briquettes generated.

Oct 1, 2019

By Richard L. Stotlar

Introduction During the last decade, the metallic minerals segment of the industry could be categorized as a "feast-or-famine" business. It is no secret that metallic minerals are cyclical. Employment opportunities greatly depend on the supply and demand for its mineral products. It is also not unusual for there to be a lag between the industry's manpower requirements and academia's ability to produce new graduates. Due to this lag, there will be years with manpower shortages, as in the mid-1970s. At other times, supply will exceed demand. The question is where will the jobs be in the years to come? This presentation will review reasons why employment opportunities have declined within the metallic minerals industry. It will also predict future demand for mineral engineering graduates. And it will outline strategies for obtaining an employment offer. Historical Review - Employment From 1977 through 1983, about 75% of all metal mining employees were directly engaged in production activities, down from 83% in 1965. This decline reflects increased use of labor saving equipment, and more government regulation and foreign competition. Metal mining's employment decreased from 74,000 jobs in 1982 to fewer than 68,000 in 1983 - an 8% decline. The overall industry is having these problems because of the general downturn in the economy. For example, at the beginning of this decade, US automobile and steel industries were in trouble. Interest rates were too high and volatile. This adversely affected construction, housing starts, and manufacturing. All these industries, being large users of base metals, drastically affected the metals industry. US copper companies are still having problems. Reports indicate that many copper employers have cut production, laid-off workers, and permanently closed mines, refineries, and smelters. A decline in the demand for US produced metal products, such as copper, obviously affects some mineral engineering employment opportunities. Other factors to consider when looking at employment opportunities and why it has become difficult for US metal producers to compete in the world market include: • The grades of ore bodies of many US minerals are considerably lower than the grades of ores being mined elsewhere in the world. • The grades of ore bodies currently being mined in the US are steadily declining. • Foreign producers are largely government controlled and are not necessarily subject to the realities of supply and demand. • US environmental regulations have considerably added to production costs. Foreign producers in most countries do not have to worry about these additional costs. • US mines are getting deeper. This adds to the cost of production because of the increasing distance the ore has to be transported. • Plants and equipment are outdated. Many companies find themselves operating with equipment and plants that need modernizing or replacing. This obviously hinders competitive productivity. • Labor and management have had problems. Work stoppages in certain mining businesses and high wage and benefit costs in relation to foreign producers place US producers at a disadvantage. • Much land is unavailable. The US government owns most of the land considered to have the best potential for minerals development. Most of this land is unavailable for mining or exploration. Therefore, it appears that finding employment with a company whose primary business is mining and processing most metals, such as copper, in the US will be quite restricted and competitive. Future Demand It is difficult to anticipate what key employment opportunities within the next few years will be available to mineral engineering graduates. The Engineering Manpower Commission estimated that US engineering schools awarded 72,471 undergraduate degrees in 1983 vs. 66,990 in 1982. This was the eighth consecutive year in which the number of baccalaureates awarded has increased. On a brighter note, the US government's Occupational Outlook Quarterly stated that the growth rate through 1995 for all engineers is an encouraging 49% over present levels. The estimated number of engineers employed in 1982 is 1.2 million. The numerical in-

Jan 2, 1985

By Bruno Veiga Fontana

O uso do nitrogênio como gás de injeção através de plug poroso no forno panela pode ser importante do ponto de vista econômico, no entanto pode provocar pick-up excessivo de nitrogênio caso seja realizado de forma inadequada. No presente trabalho, são apresentados os resultados de testes de injeção de nitrogênio e nitrogênio seguido de argônio em aços para produtos longos. Visando compreender os processos de absorção e sua cinética, um modelo cinético é formulado e ajustado aos dados experimentais. O modelo cinético clássico descreve bem os resultados experimentais e permite o uso para previsões do efeito da injeção de nitrogênio sobre o teor de nitrogênio no aço. Observa-se que a cinética de absorção é controlada pela agitação da panela e pela presença de elementos tenso-ativos, notadamente o oxigênio, como esperado, de acordo com os modelos clássicos do fenômeno. A técnica da injeção de nitrogênio seguida de argônio é bem-sucedida economicamente e o modelo permite a previsão e o controle da absorção de nitrogênio pelo aço.

Aug 17, 2017

By C. J. Beyke

In recent years recycling of household batteries has received increasing attention, primarily for environmental reasons. This article reviews the major battery types and some of the technologies available to recycle them. It also discusses issues such as collection and sorting which are related to battery recycling in the United States. Finally, results from research being conducted by the U.S. Bureau of Mines on the reclamation of nickel-metal hydride, alkaline, and zinc-carbon batteries are presented.

Jan 1, 1995