Search Documents

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By Eric Eisold

The Wachovia Headquarters and Arts and Cultural Campus project in Charlotte, NC includes a 1.5 million square foot, 48-story office tower, two museums, an Afro-American cultural center and a 1,200 seat theater for the performing arts. Public access to the Cultural Campus is through two pedestrian tunnels constructed under city streets connecting to parking garages. The 5.7 m wide by 4.7 m high mined tunnels were procured through a design-build contract. The tunnels were designed as initial/final shotcrete linings with a sprayed water barrier sandwiched between layers of shotcrete. In addition, the mix design was supplemented with a cementitious admixture to develop internal water resistant properties in the shotcrete.

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The National Institute for Occupational Safety and Health (NIOSH), through an informal partnership with industry, labor, and the Mine Safety and Health Administration, has developed and tested a new type of instrument known as the personal dust monitor (PDM). The dust monitor is an integral part of the cap lamp that a miner normally carries to work and provides continuous information about the amount of respirable coal mine dust in the breathing zone of that individual. Testing was conducted on 25 prototype instruments in the laboratory to verify the instruments’ accuracy as received from the manufacturer and after a period of underground use. The laboratory testing verified previous work; there is a 95% confidence that the individual PDM measurements were within ±25% of reference measurements. In-mine testing determined the precision, durability, and miner acceptance. Data from the mines showed a field precision of 0.078% relative standard deviation for the PDM and 0.052% for the recognized standard—the coal mine dust personal sampler unit. The PDM had about 90% availability for collecting valid information in over 8,000 hr of underground use. Anecdotal comments by miners indicated that they found the PDM more convenient to wear for sampling than currently used instruments because of the integration of the sampler into the normally worn cap lamp. The means of the instruments’ pre- and postmine accuracy verification test values were statistically equivalent. Additional data were collected to measure the equivalency of the PDM to the U.K. Mining Research Establishment sampler, as required by U.S. law. However, analysis of the data was more complex than originally anticipated because the variance with increasing concentration required use of a more sophisticated statistical model. Explanation of and results from this work will be the subject of a second publication. Under the broad range of test conditions covered in this work, the PDM functioned as well as the current sampler in terms of availability for use, accuracy, precision, and miner acceptance.

Jan 1, 2006

By T. Sterry Hunt

Jan 1, 1884

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984

Delhi Australian Petroleum Ltd., acting as operator for the joint interests of Delhi and Santos Ltd., has been engaged in petroleum exploration in the western Great Artesian Basin since 1958.Extensive airborne magnetometer, gravity meter, reflection and refraction seisomograph, and surface geological surveys have been carried out. Results of the surveys have considerably altered the concepts of the geology of the area.Seven exploratory wells have been drilled in the area. Results of the drilling have established the presence in the subsurface of previously unknown Paleozoic sediments which are capable of generating hydrocarbons.Production of oil or gas has not been achieved, but each phase of the exploration programme has resulted in progressively establishing the basic conditions necessary for the discovery of commercially profitable accumulations.INTRODUCTIONDelhi Australian Petroleum Ltd. commenced operations in Australia in 1958. They have subsequently been engaged in systematic exploration for oil and gas, acting as operator for their partner, Santos Limited. The methods and techniques employed are those used throughout the petroleum industry. The results of the exploration programme contribute to a better understanding of the basic geology, and concomitantly a firmer analysis of the petroleum producing potential, of the western Great Artesian Basin.Each phase has progressively enhanced the gross geological interpretation of the area with regard to favourable conditions for the generation and accumulation of hydrocarbons, but the stage has not been reached where productive potential is definitely established.Exploration status in 1958Basin configurationIn 1958 knowledge of the pre-Jurassic stratigraphy of the geographically defined western Great Artesian Basin...

Jan 1, 1964

By Terrence J. Stobbe

The authors investigated the nature, cause and treatment of 234 back injuries which occurred in 156 different situations in underground coal mines. A detailed interview was conducted with each injured miner as 137 variables were explored to provide a complete picture of the injury scenario. The miners worked at 23 mines in six states. An important finding of the study was that sudden movement, which occurred in 527 of the injuries, is a more frequent factor than heavy lifting in causing hack injuries. Along with sudden movement, other major injury causing factors were equipment seat design, lifting, cable handling, and slips/trips. No significant differences were found between the injury scenarios associated with lost time and non-lost time injuries; thus, both sets of scenarios should he used in doe loping back injury control strategies. Medical treatment and rehabilitation varied in content and quality. Dialogue between the medical, rehabilitation and mining communities is needed to develop an effective treatment strategy. Back injury control related training was found to be inadequate in most mines. Mine specific training for physical stress recognition and potential sudden torte release should he added to the training currently given. Based on the information collected in this study, recommendations were made regarding equipment design, mechanical assists and procedures for material handling, training, etc., which, if implemented, will assist in reducing the frequency of back injuries in underground coal mining.

Jan 1, 1989

Preparation of MgO Nano-Particles with Magnesite

Sep 13, 2010

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

The importance of the Broken Hill mining field may be gauged from the fact that since the discovery of the ore-body in 1883, till the end of 1931, approximately 43,000,000 tons of ore have been raised.The lode covers a length of 31 miles, and in places is upwards of 300 ft. in width. The ore, as at present mined, consists of an intimately blended mixture of lead and zinc sulphides with silver and gangue minerals.Structurally the lode conveys the impression of a huge longitudinal arch (when viewed from the east or west), having its apex or crown near the centre of the field, in the leases of the Broken, Hill Proprietary Co. Ltd., where the lode outcropped at the surface.The minimum depth of the lode in the Proprietary mine was some 500 ft. from the surface, but huge undulations, having an average pitch of 45°, carry the extensions of the arch gradually deeper, to those places where active stoping operations are now in progress in the workings of the North mine at one extremity, and the South and Zinc Corporation mines at the other. The depth of the lode from the surface, as exposed at present, is approximately 1700 ft. at these extremities.The structure and physical character of the ore-body, and its containing walls, are so complex and varied that almost every type of mining problem is met with.

Jan 1, 1932

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By Marília Silva Cavalcante, Filipe Brito Marinho de Barros, Suelen Silva Rocha, Jorge Luiz Valença Mariz

A seleção adequada da taxa de produção de um empreendimento mineiro tem influência direta na possibilidade de sucesso do projeto, assim como a definição do porte e quantidade de equipamentos empregados em sua operação influenciam a maximização do Valor Presente Líquido (VPL). Nesse processo, a análise de risco na variável de saída aliada à análise de sensibilidade fornece resultados mais consistentes, visto que considera os riscos e incertezas de um projeto ao longo de sua vida útil. Este estudo teve como objetivo analisar a operação em uma mina de agregados a partir da consideração de quatro diferentes conjuntos escavadeira-caminhões através do método do Valor Anual Uniforme Equivalente (VAUE), comparando-o com o método do VPL. Foram revistas as avaliações econômicas efetuadas em estudo anterior, no qual foi obtido o VPL e efetuadas as Análises de Risco e Sensibilidade em cada um dos cenários, e foi acrescida à análise a metodologia do VAUE, sendo esta também submetida à análise probabilística. Foi verificado o desempenho de cada escavadeira e seus correspondentes caminhões para diferentes taxas de produção em ambas as metodologias, permitindo concluir que, para um mesmo número de unidades de transporte e contanto que a taxa de produção requerida seja possível, quanto menor o porte do equipamento, mais econômico é o cenário. Por outro lado, quanto maior a taxa de produção do empreendimento, mais rentável este será.

Oct 3, 2019

By C. Lemire, A. Biscaro

Ferro-alloys are sold according to the size grading specifications of users. Fines are produced during crushing and the amount produced depends on the crushing process and the physical characteristics of the ferro-alloy. The market value of fines has declined. Market demand is very weak and in some extreme cases is nonexistent. An induction furnace melt process has been developed to solve this problem. The process feasibility has been demonstrated on a small scale with charges of approximately 2.5 kg. The piloting was carried out using a 100 kW furnace with a metal liquid capacity of 140 kg. The operating parameters were determined during the pilot process. The procedures were defined and the equipment required for melting fines produced at the client's site was sized. With the production of ingots, the client can now recover the full value of ferro-alloy fines.

Jan 1, 2004

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By B. Burke, R. Colquhoun, K. Thomas, R. Walton, D. Fentie

The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources. The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3½ year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.

Jan 1, 2001

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By T Sylow, A Correa De Araujo, M Gotelip Barbosa

ArcelorMittal is among the largest world’s producers of iron ore. With a geographically diversified portfolio of iron ore and coal assets, it is strategically positioned to serve the network of steel plants, as well as supply the external global market. ArcelorMittal Mining has a global portfolio of 14 iron ore operating units across Brazil, Bosnia, Canada, Kazakhstan, Liberia, Mexico, Ukraine and the United States. Iron ore products include concentrate for sintering and pelletising, pellets, directly shipped fines and lump ore. This paper presents an overview of ArcelorMittal iron ore mines including iron ore typologies and the annual production of each unit. It will also briefly discuss the processing required in order to obtain marketable products.CITATION:Gotelip Barbosa, M, Correa De Araujo, A and Sylow, T, 2017. Overview of ArcelorMittal mining operations and research and development, in Proceedings Iron Ore 2017, pp 161–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931