Search Documents

By Maria Anita de Paula Negreti

Neste trabalho, foram obtidos compósitos poliméricos de Óxido de Grafite (GO) incorporado em Poli(metaclilato de metila) (PMMA). A obtenção do Óxido de Grafite foi realizada pelo método de Hummers modificado. Em seguida foi ainda adicionada uma etapa secundária de tratamento térmico à 1000ºC no GO obtido a fim de expandir as lamelas de grafite e remover os grupos funcionais aderidos durante o ataque ácido do grafite. As cargas obtidas foram caracterizadas com o auxílio das técnicas de Difração de Raios-X (DRX), constatando a expansão das folhas após o tratamento térmico. O estudo comparativo dos compósitos de matriz polimérica com 3 % de concentração de GO antes e após o tratamento térmico foi realizado com o objetivo de entender a contribuição nas propriedades reológicas do polímero com a adição da carga de GO. Os resultados reológicos apresentaram um aumento da viscosidade complexa tanto no ensaio de Varredura de Tempo, quanto no Cisalhamento Oscilatório de Pequenas Amplitudes (COPA).

Aug 16, 2017

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960's was done on coking coals.

Jan 1, 1981

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By A Audétat, W T. Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Middle and Lower Yangtze River metallogenic belt is one of the most important polymetallic resource areas in China. Iron oxide-apatite deposits, mainly distributed in Ningwu and Luzong volcanic basins, are a distinct type of iron deposits in this region. These deposits have a close temporal and spatial relationship with Mesozoic dioritic porphyries and are characterised by magnetite-apatite-pyroxene/actinolite ± anhydrite assemblage and large-scale sodic-calcic alteration.Widespread multiphase inclusions in pre- to main-mineralisation stage pyroxene and garnet in Meishan (in the Ningwu basin), Luohe and Nihe (both in the Luzong basin) iron deposits were trapped at ~780°C in extremely saline brines (~90 wt per cent NaCl equivalent), consisting of Na (13–24 wt per cent), K (7–11 wt per cent), Ca (~7 wt per cent), Fe (~2 wt per cent), Cl (19–47 wt per cent) and SO4 (3–39 wt per cent), based on petrologic, microthermometric, Raman spectroscopic studies and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of natural fluid inclusions and synthetic analogues. The high Cl/Br, Na/B and S/B ratios in brine inclusions and the heavy sulfur isotopic values of anhydrite and pyrite (d34SAnh = +15.2 to +16.9‰, d34SPy = +4.6 to +12.1‰) suggest a significant contribution from both halite- and anhydrite-bearing sedimentary rocks. The involvement of evaporites caused the production of large amounts of high-salinity brines with apparently enhanced capacity to extract iron from the dioritic intrusions.According to their geologic features and the above characteristics, these iron oxide-apatite deposits are considered to be a special type of iron oxide copper gold (IOCG) deposits characterised by high contents of Na, Ca, Cl and SO4 in the ore-forming fluids. Moreover, we believe that evaporite-bearing sedimentary basins are more prospective than evaporite-free ones for these kinds of deposits.CITATION:Li, W T, Audétat, A and Zhang, J, 2015. The connection between evaporites and iron oxide-apatite deposits, Yangtze River, China – laser ablation inductively coupled plasma mass spectrometry analysis of Na, S, Cl and Br in fluid inclusions, in Proceedings PACRIM 2015 Congress, pp 623–630 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By S. J. Duda

Procedures for detecting and locating seismic sources are adapted to the case of entrapped miners. During an emergency the entrapped miner is likely to generate seismic signals, by knocking against the walls of the shaft. With a seismic array station deployed near the disaster area, the seismic signals can be recorded. Two algorithms are presented for the location of the source from the arrival times of a seismic phase: The first algorithm produces one, most probable location, under the assumption of constant velocity of propagation of seismic waves in the medium. The second algorithm is similarly applicable, however without any restriction on the seismic velocities in the medium between the source and the array. While the first algorithm uses an analytic approach, the second one is based on a trial and error procedure. The second algorithm gives locations with arbitrarily high accuracies, depending only on the accuracy of arrival time measurements and on the compatibility of the true velocity distribution and the assumed velocity model. The algorithm is shown not to require under certain conditions direct .arrival time measurements, thus eliminating a potential source of errors in the location of entrapped miner.

Jan 1, 1973

By J. P. Ducarme

Numerous fatal/nonfatal accidents involving underground workers struck by powered machinery occur yearly, with continuous miners and roof bolters involved in the majority of these accidents. In an attempt to reduce these accidents, researchers at the the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory conducted studies of operator interactions with the motions of continuous mining machines and roof bolter boom arms. These operators generally perform their tasks in close proximity to the equipment in confined workspaces, often employing awkward postures. Since experiments with human subjects using the actual equipment were not feasible due to safety concerns, researchers opted to conduct controlled experiments in laboratory settings. Utilizing motion capture technologies and computer simulations, the studies collected data on equipment and operator movement in a range of seam heights and working postures. This article details the results of these studies to examine operating speeds based on usage and seam height.

Jan 3, 2010

By Forrest T. Moyer

INJURY experience in the metal and nonmetal mineral industries during 1964 was better in rates of occurrence but worse in severity rates than in 1963. The frequency rate of injuries per million man-hours was improved at metal mills, nonmetal mines, and sand and gravel operations, and was virtually unchanged at metal mines; however" the rate of occurrence of work injuries at nonmetal mills, stone operations, nonferrous reduction and refining plants, and slag plants was higher than in 1963. The severity rate of injuries during 1964, data for which are presented for the first time in this chapter, was better at metal mills, nonmetal mines, stone operations, and slag plants. However, the severity rate was worse at metal mines, nonmetal mills, sand and gravel plants, and nonferrous smelters.

Jan 1, 1965

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

By Marcelo Gonçalves Pereira

Os roletes de planicidade estão instalados na posição frontal dos laminadores. O histórico do equipamento mostra um tempo entre falha de 6 meses, caracterizadas principalmente por fratura da gaiola e danos na pista dos rolamentos lado acionado. Danos no eixo na região de montagem aumentam em torno de 10 horas a indisponibilidade da máquina para recuperação do mesmo. A partir da RCFA realizada nos rolamentos falhos, identificou-se deficiência de lubrificação, sinais de ovalização, descascamento e desalinhamento na pista de rolagem, fratura da gaiola. Com base nos modos de falha foi realizado a alteração e adequação da lubrificação dos mancais, melhora do sistema de vedação e alteração da disposição de montagem dos rolamentos de contato angular de back-to-back (“O”) para face-toface (“X”). Com as modificações realizadas os roletes atualmente operaram por mais de 14 meses sem ocorrência de falha.

Aug 17, 2017

By Rodrigo Vitorino da Silva

Ligas a base de zircônio são utilizadas na indústria nuclear devido à suas boas propriedades mecânicas, baixa absorção de nêutrons e boa resistência à corrosão. No entanto, durante a operação do reator, o hidrogênio é absorvido pela liga, resultando na formação de hidretos. Para aumentar o tempo de operação desses componentes é necessário o desenvolvimento de novas ligas que retardem ou diminuam esse efeito. Este trabalho tem como objetivo avaliar a influência dos tratamentos termomecânicos no zircônio puro, através de testes que avaliem a corrosão, absorção e dessorção de hidrogênio nas condições laminada a frio e tratada termicamente. Análises de difração de raios-X indicam a existência de uma matriz Zr-a para as condições analisadas. Após a hidrogenação são formados ZrH e ZrH2. O zircônio puro encruado absorveu 1,23%p H. O zircônio puro laminado e tratado termicamente absorveu 0,85%p H. O resultado de DSC mostra que a decomposição dos hidretos ocorre em faixas de temperatura entre 318 e 368°C para a condição tratada termicamente. Para condição laminada, o resultado mostra uma transformação de fase entre 565 e 650°C. O conjunto de resultados permite concluir que a amostra tratada termicamente absorve menos hidrogênio, porém o início do processo é menor. A amostra tratada termicamente é menos resistente a corrosão e a velocidade da corrosão é menor.

Aug 16, 2017

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

By Luciano Aparecido Kempski

O ferramental utilizado em processos de conformação é de grande interesse da Engenharia de Superfícies devido às características tribológicas específicas encontradas nestes processos. Portanto busca-se sempre melhorar o ferramental para se obter menores coeficientes de atrito, desgaste e adesão de material sobre a superfície da ferramenta, sendo empregadas diversas técnicas de tratamentos superficiais como a nitretação e os revestimentos depositados via PVD. Uma variável importante do par tribológico é o coeficiente de atrito desenvolvido entre as superfícies em contato nos processos de conformação a frio, portanto foram realizados ensaios de pino-sobre-disco e ensaios DST, para determinação de coeficientes de atrito em pares tribológicos. Desta forma, chapas de aço inoxidável austenítico AISI 304 foram conformadas sobre uma superfície de um aço ferramenta DIN X100CrMoV8-1-1, com o propósito de se conhecer o atrito desenvolvido entre os materiais. As amostras foram nitretadas a plasma e ou revestida com TiCN, posteriormente, a caracterização da microestrutura e as propriedades avaliadas através de ensaios mecânicos e tribológicos. O ensaios proporcionaram obter valores de coeficiente de atrito para as condições de tratamentos e lubrificação utilizados e as análises dos resultados mostram um aumento da dureza superficial das amostras tanto nitretadas quanto revestidas com TiCN e uma redução do coeficiente de atrito significativa quando se faz uso do revestimento.

Aug 8, 2018

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T. A. Ngcobo

Paper written on project work carried out in partial fulfilment of BSc Eng (Mining)degree The purpose of this report is to assess the risks faced by mines in dolomitic compartments in particular Kloof 8 shaft. The dolomites of the West Rand comprise one of South Africa?s most natural water resources, and overlie the reefs of the richest gold mines in the world. The pumping of water from the dolomitic aquifers to prevent flooding has caused the natural water table to subside, and the resulting cavities within the dolomite rock formations that overlie many gold deposits sometimes collapse, causing sinkholes. These impacts of the mining industry could worsen over time if preventative measures are not taken. This report discusses these impacts in detail, more specifically the risks to which operations in dolomitic compartments are exposed. A risk analysis was carried out to access the risks that the organization could face and it was this analysis that allowed one to examine the best methods to combat the problems. Other factors such as geological features and seismic events were also considered for the evaluation. To aid with the completion of this work various resources were utilized. A literature study was undertaken, information was gathered from various experts who specialize in dolomitic studies, evaluations were conducted and conclusions reached. The results from the project indicated that preventative measures should be implemented and correct procedures put in place to prevent any disasters.

Jan 1, 2006

By S Henderson

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Microprobe analyses.of sphalerite grains from the Waitangi deposit mostly range from 0.8 to 1.5 mole % FeS, although one sample contains 9.5 mole % FeS. Arsenopyrite from Waitangi yields a range from 33.1 to 34.6 atomic As (%). There is no discernible correlation between the FeS content of sphalerite and gold grade in the Waitangi deposit suggesting that gold deposition is probably not controlled by changes in temperature and activity of sulphur aS2 that control the FeS content of sphalerite. The possible causes for gold deposition are thought to be boiling, mixing and changes in pH. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-ehalcopyrite samples yield a narrow range of d34SCDT values (-1.0 to 0.9 ë;n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source. However, the source of light sulphur in the late pyrite grains is not known. Preliminary fluid inclusion+studies indicate homogenisation temperatures between 173¦ and 284¦C and salinities of 0.23.0 NaCI equiv. wt % (uncorrected for C02). Vein quartz at Waitangi yields d18OSMOW values from 6.8 to 12.7 ë (n=23). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1-5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in d18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that d18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1993

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By João Júnio Pereira Lino

Este trabalho tem como objetivo demonstrar a influência da laminação de desbaste durante o processo de laminação termomecânica de um aço microligado ao Nb, Ti e V, obtido em um laminador Steckel, nas suas propriedades mecânicas. Duas variações do plano de passe para realização da laminação de desbaste foram propostas. As variações consistiram na diferenciação da redução passe a passe de forma a obter diferentes refinamento de grão ao fim do processamento de desbaste. O processamento de um aço com composição química adequada à obtenção de propriedades mecânicas compatíveis com o grau LNE380 especificado na norma ABNT NBR 6656 é demonstrado. Foram alcançados limites de escoamento a 0,2% de deformação e a resistência à tração na condição 1 de 459MPa 563MPa e na condição 2 de 505MPa e 601MPa respectivamente, sendo que na condição 2 foram obtidos acréscimos de em torno de 40MPa em ambos LE e LR.

Oct 30, 2017