Search Documents

By I. B. Tulu, M. M. Sears

"In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial, yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground fall related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground fall related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 21 longwall mines were visited, representing about 40% of the currently active longwall mines in 4 of the 5 major US longwall producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. The results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries. INTRODUCTION Maintaining ground stability in gateroad entries is essential for longwall productivity and safety (Campoli, 2015). In 2015, 148 unintentional roof falls were reported in US longwall mines. About 34% of these resulted in mineworker injuries. Safety considerations not only include injury from roof and rib falls but also egress from the longwall face during an emergency (Mucho et al., 1999). Over the past 30 years, a number of researchers have studied longwall tailgate support performance (Mirabile, 2015). This research aims to take a snapshot of the ground support installed in modern US longwall mines and provide a supplement and update to the overview provided by Barczak (2005). This will provide a framework for future research into improving gateroad support systems. BACKGROUND Large unplanned roof falls at or above the primary support or those impeding travel and/or ventilation must be reported to the Mine Safety and Health Administration (MSHA). Reportable roof falls, normalized based on production in million metric tons, generally relate to the amount of roof exposed during the mining process (Pappas and Mark, 2012) and provide an evidence-based statistical background for this review of current support practices. Figure 1 shows the reportable roof fall rate in US underground longwall mines for the period 2006-2015 (MSHA, 2016). Over the past decade, roof fall rates have shown a gradual decrease with numbers now at a rate nearly half of what was observed just five years ago. However, over the past few years, roof fall rates in US longwall mines appear to have stagnated at levels just over 1 per 2,000,000 tonnes mined."

Jan 1, 2017

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By M. E. Charles

The use of water flowing as a lower layer to reduce pressure gradients in petroleum pipelines was investigated using 17.5 deg. A.P.I. Lloydminster crude oil in a 1-inch laboratory pipe-line and a 21h-inch field pipeline. The method was found to be very effective in reducing the pressure gradient below that for the oil flowing alone. The factor by which the pres-sure gradient was reduced varied with the percentage of water added, and in general exceeded 10 for water contents ranging from 40 to 60 per cent. Within this range of water content the pressure gradient reduction factor was independent of the oil flow rate.

Jan 1, 1960

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

Jan 1, 1882

By J. A. Cox

The Ashanti mine is located within the Lower Proterozoic Birimian of Ghana, and covers a concession of 474 square kilometres at its Obuasi operations which comprise large scale underground, surface and tailings treatment facilities. The mine had operated for a century at the end of 1997 and had produced nearly 25 million ounces of gold, a significant proportion of which came from the underground operations. This paper covers the strategy under which exploration for both surface and underground mineral resources was instrumental in enabling the expansion programme to go ahead together with the methodologies and results that have developed in the exploration area over the last five years. Within capital expenditure constraints, the objective on surface is to replace oxide depletion with a secondary objective of discovering new sulphides in areas other than the main trend. In the underground, the exploration strategy is directed at replacement of both underground and surface sulphide depletion, minimising finding costs and assisting the development of long lead time infrastructure. The exploration application describes the methodologies in use for both surface and underground exploration that have been developed in recent years in conjunction with a description of a major review conducted in 1995/96 of the exploration database using an integrated approach, geochemistry, geophysics, remote sensing and structural geology. A revisit of soil geochemical data in particular, and modification of exploration methodology led to the success in finding relatively significant new oxides in 1997.

Jan 1, 1999

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By W. W. Adams, T. D. Lawrence

"The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior for the promotion of safety in mines and quarries, has just been closed for seventeenth consecutive year. Enrollment covered more plants than in any previous contest. Moreover, a larger volume of employment was represented than in the contests of previous years, and several new plants were enrolled for the first time. Six safety trophies are awarded annually in these competitions one to the leading plant in each of six groups. An anthracite, mine in Pennsylvania, a bituminous-coal mine in West Virginia, a metal mine in Tennessee, a nonmetal mine in Virginia an open-cut mine in Minnesota, and a quarry in Alabama won the 1941 trophies.To be eligible to win a trophy, a mine or quarry must have had at least least 25 men working under ground or in the pit for not loss than 100 days. The number of man-hours worked must total 30,000 or more. Mines or quarries having no accidents during the year are rated according to the number of man-hours worked. If there are no plants with accident-free records, the mines and quarries in each of the six groups are rated according to their accident-severity rates; the plant having, the lowest rate is declared the winner.The Sentinls of safety trophies presented to the winning mines and quarries in the six groups were donated by the Explosives Engineer magazine to promote safety in the mineral industry. They are held by the winning companies for 1 year or until won by other mines and quarries."

Jul 1, 1942

By 12670

The Cigar Lake project will develop the world’s second largest high-grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the highgrade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2006.

Jan 1, 2004

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By J. H. Fowler

Canada's gypsum industry began over two hundred years ago in the Maritime Provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada's ten provinces. Thirteen open-pit and three underground mines produced a total of 8.38 million tonnes of crude gypsum and seventeen processing plants manufactured 2.49 million tonnes of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production, however, competition from foreign producers and by-product gypsum poses a growing threat to Canada's gypsum mining industry.

Jan 1, 1987

By Dirk van Zyl, Lysa Morishita

Mining companies are increasingly approaching the social aspect of sustainable development within the rural communities that neighbour their projects and operations. Rural community engagement requires significant effort and resources, and it can be extremely challenging for mining companies to earn and sustain social capital. The focus on rural, proximal community engagement is not to be understated and has led to significant benefits in many communities. However, opposition to mining projects is often exhibited in urban environments, where there may be potential for mining companies to gain social capital with relative ease. Cities tend to have existing frameworks for community engagement and public activation, such as annual parades and festivals, that make it easy for a mining company to provide financial support or value-in-kind. Local organizations and community groups can achieve the same amount of engagement in an urban environment with significantly less effort required from the mining company. By applying simple marketing principles to community engagement strategies, corporations can increase awareness for their business and encourage city residents to think critically about the origin of resources. Unlike many corporations, mining companies are not marketing or selling products to individual consumers. From this arises the opportunity for a company to use marketing to promote other positive initiatives and, as such, connect their brand with positive messaging thus earning social capital. This may lead to a wide variety of secondary impacts including benefits to recruitment efforts, increased political support, and positive media coverage. This paper explores these matters with special reference to Vancouver, BC, Canada and the mining companies Teck and Goldcorp.

Jan 1, 2017

Every automatic citizen is an automatic recipient of a miner's right under the present Mining Act (Chapter 195), but this alone does not entitle any automatic citizen to mine for minerals on any land, even his customary group's land. Without complying with requirements of the Mining Act, any automatic citizen who engages in mining solely on the basis of a miner's right would be mining illegally. He would also be engaged in illegal mining if he mines on customary or other non-government land. Even if mining is legally pursued by an automatic citizen, he does not acquire ownership of minerals without first making the required royalty payments to the State.

Jan 1, 1991

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By Charlie Adcock, Rob Farnfield, Andy Wetherelt

The ISEE Blasters Handbook gives guidance on the level of air overpressure likely to cause occasional window breakage (151dB) and general window breakage (171dB). A long-term safe level of 140dB is also suggested. This guidance is widely used by demolition and other contractors to assess damage zones in the region of explosive applications employing unconfined charges. Other reference material gives more detailed guidance relating to window area, aspect ratio and glass thickness. Despite the guidance given in these references, complaints by members of the public regarding window breakage continue to be received by explosives engineers from air overpressure levels well below the longterm safe limit. Such complaints are not limited to the use of unconfined charges but can even be generated from the highly confined use of explosives in quarry blasting. This paper describes a series of experiments with explosive charges fired in unconfined conditions close to various window configurations. The aim of the work was to test the existing guidance levels and to extend the knowledge base in this area. Topics covered include the role of differential pressure across windows in the walls of an enclosed space such as a room.

Jan 1, 2006

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest are reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By Antonio Fabiano de Oliveira

Estudos de laminação com revestimento de cromo e influência nas propriedades foram realizados com o objetivo de aumentar a produtividade dos cilindros. Para tal, foram utilizados cilindros cromados para laminação de chapas de cobre, com amostragem da técnica de réplica epoxy. A compreensão da correlação entre microestrutura e propriedades do material é objeto de grande interesse e, ao mesmo tempo, necessário para aplicação prática na laminação a frio, combinando revestimento e produtividade. O objetivo da pesquisa atual é comparar as propriedades tribológicas do cobre antes e depois da laminação, no cilindro de trabalho e chapa, com e sem revestimento de cromo.

Oct 30, 2017

By Joe Pease

"The demand for minerals and metals is increasing. Head grades of ore bodies are dropping. Remaining ores are becoming finer grained, more complex, and more logistically challenging. Mineral processing – in particular comminution – already consumes a huge amount of energy. But in 20 years’ time, it will require about six times as much energy as today to meet the world’s mineral demand.Unless we do something different.As minerals professionals, it is our job to find that “something different”. The world is relying on us. Of course, we must look for new breakthrough technologies and techniques. We must find them, and we will find them – most likely in surprising areas.But what if we also already know how to make 30-50% improvements to efficiency? Just by using existing technologies, by applying modern analytical techniques, by custom designing our plants, by applying manufacturing principles, by breaking down our management silos between disciplines.The thing is, industry professionals already know this. Yet – in spite of a lot of intelligent people trying very hard – we just can’t seem to make it happen.This discussion considers why, despite our best efforts, we don’t get the best out of what we already have. Why we are wasting energy and money. Once we understand why, we can set about unlocking that value and improving industry productivity and energy efficiency. We will discuss the role that professionals and volunteer professional organisations like CMP and CEEC can play in catalysing the changes."

Jan 1, 2015