Search Documents

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By Greg Beckstrom

On Oct. 1-3, SME?s Twin Cities chapter (SME TC), in cooperation with the University of Minnesota ? Duluth?s Precambrian Research Center (UMD-PRC), cohosted a symposium on silica sand mining and processing. The conference was held at the Earle Brown Heritage Center near Minneapolis. The symposium was followed by a day-long field trip to operating mines, processing plants and loading facilities located in southwestern Wisconsin. Speakers and attendees at the symposium included university professors, industry experts, regulators, mining company representatives, equipment suppliers, consulting engineers and service companies. Approximately 320 people attended the conference. In addition, about 50 people who oppose mine development and the oil and gas industry showed up to voice their displeasure with the event and those companies that operate in this space.

Jan 1, 2012

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

By Guilherme Duarte Moreira

Com o objetivo de melhoria dos resultados de desempenho operacional identificouse uma oportunidade em reduzir o tempo de trocas programadas (Setup) na Laminação de Fio Máquina na Usina Siderúrgica de Ouro Branco. Utilizando a metodologia SMED (Single Minute Exchange of Die), obteve-se grande redução do tempo de Setup. Como esta metodologia já se demonstrou uma excelente ferramenta para redução dos tempos de setups, foi idealizado uma abordagem mais completa, sendo desenvolvido um modelo para aplicação para as paradas programadas para manutenção. Esta aplicação corroborou um enorme ganho, tanto na definição do tempo de parada programada, quanto no planejamento e padronização das atividades.

Aug 16, 2017

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By Pedro Augusto Silva de Lima

As ligas do sistema Cu-Al-Ni sofrem Transformações Martensíticas Reversíveis (TMR) e podem apresentar Efeitos Não Elásticos, incluindo o Efeito de Memória de Forma (EMF). Elas podem ser utilizadas nas diversas áreas e são promissoras para substituir ligas do sistema Ni-Ti. Neste trabalho foram estudadas três ligas distintas: monocristalina e policristalina Cu-Al-Ni e policristalina Cu-Al-Ni-Mn-Ti, dando atenção a análise da estrutura e comportamento mecânico, em seu estado inicial e após tratamento de betatização. Nas três ligas foram identificadas as fases martensitas ß1 e Y1e as fases R e ß1. A liga Cu-Al-Ni-Mn-Ti ainda apresentou o composto Cu2AlTi. Durante a deformação, as três ligas sofreram TMR, induzidas por tensão, com reorientação das fases envolvidas. O tratamento de betatização aumentou a plasticidade, sendo mais notável na liga policristalina Cu-Al-Ni. A liga Cu-Al-Ni-Mn-Ti se mostrou como a mais frágil, sofrendo a fratura antes de alcançar 10% de deformação. A liga monocristalina se mostrou a mais promissora para realizar EMF, revelando maior deformação armazenada no patamar de pseudoescoamento.

Aug 17, 2017

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By R. W. Stahl

The use of continuous mining machines has greatly minimized the necessity for blasting in coal mines, even during pillar recovery; however, explosives are still used to blast stumps. The use of improper blasting materials, improper procedures, or both has caused mine explosions and fires, with loss of life and property damage. Researchers and manufacturers are continuously improving explosives and blasting accessories; use of the more recently developed materials will make the blasting operation safer. Extreme caution is mandatory when blasting stumps, as the ignition of methane or coal dust may trigger an explosion or cause a fire. Since the blasting of stumps will no doubt continue, although often unnecessarily, this paper summarizes recent findings published by the Bureau of Mines and recommends safer methods.

Jan 1, 1962

By Gerald W. Longenecker

For decades, traditional hydraulic engineering approaches have been used for sizing stream channels when stream relocation efforts have been necessary to allow for the advancement of quarry and other surface mining operations. These approaches have been based on various ydraulic models to design channel cross sections and slopes that could pass the required regulatory design storm such as the 2-, 5, lo-, 25-, 50-, or even loo-year events. Designing the stream channel to handle these more extreme ,storm events would often lead to large channel designs which required extensive bank and channel bottom stabilization techniques including concrete, rip rap, gabions, or other expensive approaches. The constructed channels often required ongoing maintenance to remove accumulated sediment and other debris which would settle out and reduce the hydraulic capacity of the channel.

Jan 1, 1998

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

To alleviate the hazard to personnel and danger to equipment caused by fires on large, mobile vehicles. The Approach: A system which automatically senses a fire at its early stage of development, warns the driver of the danger, and activates fire extinguishers in the zone of combustion, How It Works: The automatic fire protection system utilizes both thermal and optical sensors to detect the heat or light given off by a fire in the area of concern (Fig. 1). The system warns the driver of the hazard and then automatically extinguishes the fire with pressurized S-C class powder. The system can also be activated manually from the operator's cab or from ground level. Further, the automatic sequencing of the system can be manually overridden by the driver if he determines that the fire sensors have malfunctioned to cause a false alarm.

Jan 1, 1974

An important consideration in any mining operation is waste disposal management. Tailings management at Macraes gold mine allows for the disposal of tailings into fully engineered embankment dams and overburden material to be incorporated as construction material into those embankment dams. This paper outlines the current tailings management practices.

Jan 1, 1992

By Herman W. Hill

This report summarizes research into the root causes of failures in mine power systems which impact safety and reliability. Abnormally low fault currents, due to arcing faults, self-excited systems, and fallen trolley wires are examined and quantified. The reliability of components which are critical for safety is studied, as well as reliability of components which are crucial to the mining pro cess. Failure rates are found through in-situ tests, accelerated life tests, studies of mine maintenance, and fault-tree analysis. Reliability data is used to predict fatalities and lost-time accidents through computer-aided fault-tree analysis. Analytical support tasks reported include the deriving of trailing-cable ampacities under cyclic loading, and the measurement of connected ground beds.

Jan 1, 1981

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By G Boyd

The Nokomai Gold Mining Project commenced production in January 1992. The Project continues a history of mining in theNokomai Valley which extended from 1863 to 1942. L & M Mining Limited have held interests in the valley since 1980. In 1990 the Nokomai Joint Venture was formed with the Hore family, the owners of Nokomai Station, to mine a large alluvial gold resource in the valley. The mine is located adjacent to the Mataura Brown Trout fishery and required extensive environmental studies prior to granting of permits. The mine is budgeted to work for 20 months, processing 460 000 m3 of wash material. During this period, contract miners, Downer Mining Limited, will move in excess of seven million cubic metres of overburden from the deposit.

Jan 1, 1992