Search Documents

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the "carbon monoxide ratio") it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure· indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By Peter Campi, Harry R. Asche, Ian P. Callow, Edmund G. Taylor, P. Scott Smith

The US$1,850 million EastLink project is a 39km tollway and includes twin 3-lane,1.5km long, undrained driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and so to help preserve the unique flora and fauna in the area. This paper describes several of the key issues in the tunnel design and construction, including: the integration of the temporary support design with the Contractor’s tunnel excavation and support procedures, including sharing of responsibility between the Designer and Contractor for support type selection and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. detailed hydrogeological assessments during the design and construction phases to allow confirmation of design loads for the tunnel lining design and the various suite of waterproofing tools in order to meet the project inflow requirements. development of a pre-cast invert solution to the main tunnel secondary lining to enable faster lining construction and to minimize risks to the tunnel membrane associated with fixing reinforcement and construction traffic.

Jan 1, 2007

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By Ravi Sahu

"In the global mining industry, there are those who seem resigned to the fact that the mining industry has always operated according to certain time-tested principles that don’t involve jumping on every new technological trend. Others expect that mines will soon have autonomous electric vehicles running around the clock. The truth lies somewhere in the middle. In business, as in life, that is usually the best path to follow.The instant access to people and information provided by 21st-century technology continues to push businesses in all industries toward greater efficiency and unheard-of levels of modernization. And in the world of mining, the embrace of advanced technology is all about managing risk.However, even in this age of digital information overload, some mine sites still require employees to physically download data from individual trucks to monitor payload data and inspect road conditions using a clipboard. What’s more baffling is that other mine sites still have no way of tracking tons moved at all.This isn’t due to a lack of innovation in the industry. Quite to the contrary, there is an abundance of new technology available that provides real-time monitoring of vehicle movements and tracks road conditions without the intervention of people. So why are owners reluctant to embrace advances in mining tech?Gauging the value of changeSurvey data has traditionally been captured by ground laser scans and LIDAR systems. A mine site surveyor would drive around the pit with a truck-mounted scanner to generate a point cloud. This process would be completed every few days and would take an entire day.The many cons of this method far outweigh the pros. First, it provides no visual data. If an operation has moved beyond the roller wheel and tape measure, visual pit models and LIDAR scans are typically completed once every six to 12 months by an aerial flyover, but such sporadic information gathering isn’t likely to result in the most actionable data. Moreover, given the high cost (in terms of both money and time), the numerous safety and liability issues, and the lack of flexibility in scheduling, manual processes are more trouble than they are worth.Overall, while miners are excellent operators who value innovation, their employers often try to outsource it or acquire innovators instead of investing in existing technology that can improve current operations. It is a never-ending dilemma:"

Jan 5, 2018

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By F. H. Gunnell, W. C. Dunham

"INTRODUCTION The Treasure Hill mines, situated in Dry Canyon, Ophir mining district, Tooele County, Utah, together with several other properties in the district, examined were examined by Frank L. Wideman, an engineer, the Bureau of Mines, in September 1942.In April 1945, development drilling was started on the Treasure Hill mines, which are operated under lease from the Madison Mines Co. The project was continued in 1946 and terminated in 1947.While the Bureau of Mines project was in progress, the Morgan and Fullion tunnel workings were surveyed by Bureau engineers.ACKNOWKEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative perk, and prepares the final report. The Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. The work here described was under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch."

Jan 1, 1948

By Lincoln Silva Gomes

Processos metalúrgicos durante soldagem provocam tensões residuais em peças soldadas. Recentemente foi observado um efeito de redistribuição das tensões residuais de soldagem num período de até duas semanas após o termino do processo de soldagem. Existe hipótese nossa que esta redistribuição das tensões está associada a mudança na microestrutura que ocorre no material após do processo de soldagem. Para provar esta hipótese, uma simulação física dos ciclos térmicos do processo de soldagem foi realizada utilizando a simulação física termo-mecânica (GLEEBLE). Através da técnica de microscopia eletrônica de varredura associada a técnica de difração de elétrons retroespalhados (MEV–EBSD) foi observada a variação da misorientação dos grãos e mudanças na microestrutura do material nos primeiros dias após soldagem, acompanhada de redistribuição das tensões residuais.

Aug 17, 2017

By Branagan D. F

The geology of the area studied is briefly described, together with the prospecting methods used in the search for copper, lead, zinc and uranium ore bodies.Four prospects, Mt. Corella, Yanasinga, Lawlor's and Greenmount, which were diamond-drilled, are described in detail and geochemical results are discussed in relation to the mineralization found. Copper anomalies were found wherever intrusive rocks were mapped, and showed a much closer relation to geology and mineralization than did the predominantly lead and zinc anomalies.Geochemical prospecting aids in the overall mineral search programme because of its speed and economy, as it helps to pinpoint areas worthy of detailed geological examination. Geochemical anomalies are a guide to favourable zones but may not indicate the presence of ore.INTRODUCTIONDuring 1953-55 the National Lead Company of New York carried out a search for minerals in an area south and west of Cloncurry (Fig. 1) in rocks of Precambrian age. After reconnaissance mapping, a number of prospects were chosen for closer examination by detailed geological mapping and geochemical sampling, and from these prospects, five sites were selected for drilling.This paper records the salient features of the exploration programme and discusses the geology and geochemistry of four of the prospects-Mt. Corella, Yanasinga, Lawlor's and Greenmount. Practically all the prospects examined showed high zinc "anomalies" or "dispersion" trains. Greta, Mt. Corella and Lawlor's prospects showed some copper anomalies and, to a lesser extent, lead anomalies. In particular, Greenmount exhibited striking copper anomalies.

Jan 1, 1960

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

The labour question is one that has caused mine managers much thought and anxiety and is likely to continue to do so as long as human beings exist. The difficulty is to devise some arrangement whereby the interests of miner and mine ownerare identical. Mines cannot be worked without capital, and capital is no good without labour, yet, though both have the mine in common, their interests are not exactly the same. Some men are happy so long as they can scrape through by exerting themselves as little as possible, but capitalists do not work mines for charity, they want some return for their money.Where a large number of men are employed there are bound to be examples of all sorts, good and bad, and it is because one cannot depend on all, that different methods of employment have to be adopted. Which method is selected depends to a great extent on the labour market, local conditions, nature of the ore and the way in which it occurs.A big step towards success is obtained by securing the services of good bosses, not only those who know how work should be done, but men who have a knowledge of human nature. It is a big mistake to be too lenient with a man, also to be unnecessarily harsh. A good boss will always be sought out by good men who have worked under him before, or who have heard of him from others. By a good boss we do not mean one who employs two men where one would do, or who lets the men loaf...

Jan 1, 1901

By Kenneth A. Pidgeon

This paper presents a case history on mitigating vibration problems associated with the installation of steel sheetpiles. The project in-cludes installation of steel sheetpiles for a utility trench within 40 feet (12.2 meters) of a very sensitive manufacturing facility. Numerous production line quality control instruments and manufacturing processes within the manufacturing facility are extremely sensitive to vibrations. To minimize the impact to the owner, we specified that the contractor perform a vibration study using different types of pile hammers. The results and conclusions of the vibration study are presented in this paper.

Jan 1, 1995

By Robert Smith

Deposits are global, said Barrick Gold's Smith. This means that the mineral industry, by necessity, is global. "Manufacturers have considerable freedom to decide exactly where they wish to produce whatever it is that they sell," he said. "What we sell, on the other hand, must be produced where nature chose to lay it down. The question is not so much, whether to go global, as when to do it and how to go about it." The timing of international expansion depends on external factors, often political, Smith said, and on internal ones that relate to the company's size and stage of development. "In deciding how to expand, a company is largely deciding how to adapt its existing business strategy to activity on the world stage," he said Barrick entered 1997 with 1.58 kt (51 million oz) of reserves, Smith said, annual production of 93.3 t (3 mil- lion oz) and cash flow of $463 million. Reserves in- creased 40% in 1996 and production will begin to rise again significantly in 1999. "We believe our fundamental strategy is responsible for our early development and subsequent success," he said. Barrick entered the gold-mining industry in 1983. Its corporate mandate was to create shareholder value, Smith said. From the beginning, the company took a different approach - businesslike, entrepreneurial, strategic and focused. "Many mining companies start out with a technical team and develop business and financial expertise thereafter," Smith said. "In 1983, Barrick had the business people, and then moved into mining." First, it acquired part interest in two small operations, one in Alaska and one in Ontario. Then, in 1984, it merged with Camflo Mines, which operated a low-cost underground operation in Quebec.

Jan 1, 1997

By Andrew J. Brennan, Jonathan A. Knappett, Lewis Hamilton, Michael J. Brown

"Abstract This paper investigates the compressive behaviour of screw piles in sands and the key design parameters which control this. These types of foundation elements have typically been used as screw anchors onshore (i.e. for their tensile capacity), but there is increasing interest in their potential use as compression piles for supporting offshore marine renewable energy (MRE) devices (e.g. wind and tidal turbines) in deeper water. For such foundation applications, the compressive capacity is as important as the tensile capacity and is not well understood, particularly in cohesionless soils which are a likely seabed condition in MRE applications. A 1-g laboratory study was initially conducted on small scale model screw piles in sand beds of various relative density between 25 – 88%. These experiments were used to validate a Finite Element (FE) model having a stress-dependent constitutive model, making it useful for future up-scaling of the pile size for field applications. Following validation, the FE model was used to conduct a parametric study on the effects of flange spacing ratio (s/Dflange) and flange to shaft diameter ratio (Dflange/Dshaft). By using a validated FE model for this study, it was possible to observe the failure mechanisms (through the shear strain distribution) within the soil and correlate these with the pile capacity. This information was then used to comment on the most optimal (cost-effective) pile design for supporting compressive loads. This study represents a key step towards producing design tools appropriate for the design of screw piles in MREapplications.IntroductionAs defined in this paper, screw piles consist of a central small diameter hollow steel shaft, around which thin circular steel flanges run. Their principle of operation is that the flanges are spaced so as to trap the soil between them, thereby acting as an equivalent solid pile of the outer flange diameter, with a fully-rough ‘shaft’ interface (as shearing is soil-soil). One of the most important design decisions relates to the spacing of the flanges – if the flanges are spaced too far apart, then the soil will not be effectively trapped and the pile have a lower axial capacity and stiffness (controlled by the shaft friction along the central shaft and the bearing resistance arising from the individual flanges; If the flanges are spaced too close together, then there are potentially flanges which are not contributing to the pile capacity, therefore making the pile more expensive than it needs to be."

Jan 1, 2014

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By George R. Pratt

Although the title of this paper focuses attention to the Winnipeg coal market the following remarks should be considered applicable not only to conditions in Winnipeg but to the whole western coal industry. Technical descriptions of coal and coal-burning have been omitted. These details are already covered in other numerous publications. In discussing a market the first consideration must be the product which is required to be sold. The class, quality and price at the point of origin must be taken into account and therefore this feature will be discussed before proceeding to outline conditions in the Winnipeg local market. The writer thinks of coal as a manufactured article, not, as it is generally considered, a fuel to be dug from the ground and dumped into the consumer's bin. The work of manufacturing must be considered in detail:- 1. Consider first the coal as it is in the ground: (a) What is its fuel value? (b) Where is its market? © With what will it be in competition? 2. Consider secondly: (a) What it will cost to mine the coal. (b) What has to be done to prepare the coal for market after it is mined. This must be considered in conjunction with the answer to question 1 ©. 3. Thirdly, consider the method of business to be adopted by the producer:- (a) Is it proposed to build a market on price? Or (b) On quality?

Jan 1, 1925

By Alexandre Furtado Ferreira

O presente trabalho descreve o desenvolvimento de um modelo matemático de conservação de massa e energia tendo como base a medição intermediária da sublança (Modelo Dinâmico). O modelo utiliza como dados de entrada informações sobre massa e composição da carga metálica, valores adicionados de fundentes na corrida e as informações obtidas com a medição intermediária aos 88% do sopro de oxigênio calculado pelo Modelo Estático. O algoritmo foi desenvolvido em C# e está integrado na rede de Nível 2 da CSN. Os resultados de acerto simultâneo de temperatura e carbono final de sopro obtido pelo modelo dinâmico foram superiores ao Modelo Estatístico até então utilizado. Tal fato permitiu a redução do ressopro decorrentes de imprecisão do modelo e ganho em produtividade.

Aug 17, 2017

By R. E. Mclvor

This is an update of an original dissertation on this topic by Lavallee, McIvor and Stolovitch (1992). A step-by-step, technical procedure used to measure and improve the performance of plant grinding circuits was adapted into a training program. ?Systematic Design of Instruction? was applied to: ? Determine if training was a suitable way to deliver this new technology; ? Define the technical content of the program; ? Select program specifications based on learner and context characteristics; ? Design, create and test prototypes of the training modules; and, ? Establish a process for plant implementation. The training program covers numerous skills that are extremely valuable for plant personnel, not only in the grinding area, but also for many other parts of the plant. This paper describes how new skills are brought into the workplace through designed instruction can be an effective alternative to hiring during severe skilled labor shortages.

Jan 1, 2008