Search Documents

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By Francis Chachula, Niel Erasmus

"In 2002, Titanium Corporation Inc. focused its attention on the development of a process for the recovery of valuable heavy minerals, including zircon and titanium bearing minerals from oil sands froth treatment tailings. The development of a process flowsheet to recover the titanium and zircon minerals from the Athabasca oil sand tailings has evolved through many laboratory, bench and pilot scale iterations.Initial development work focused on so-called ‘beach sand’ material, which is tailings material deposited over a period of time close to the tailings pipe discharge. The derived process flowsheet primarily consisted of gravity concentration stages, which is typical of all mineral sands operations. Titanium Corporation’s business plan calls for the utilization of tailings directly from the tailings pipeline – the process developed around the beach material is therefore risky as it differs from the live tailings in a number of aspects, with the effects on the process unknown. Titanium Corporation successfully obtained an intermediate product through a ‘bulk sampling plant’ coupled directly to an Oil Sands operator’s froth treatment tailings pipeline, during the summer of 2005. Subsequent further processing of this material resulted in poor separation or concentration of the heavy minerals due to a number of reasons. A more effective process flowsheet had to be developed.The newly derived process is basically a marriage between mineral sands technology and oil sands technology that can economically concentrate and recover the heavy minerals and entails the incorporation of a flotation process that takes advantage of the entrained bitumen in the feed to separate the heavy mineral fraction from the quartz gangue This paper will describe the newly derived process as well as the successful results of a subsequent on-site concentrator pilot campaign completed during the 3rd Quarter of 2006."

Jan 1, 2008

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Elk Creek RARE II area during the summer of 1981. The study area encompasses 18,900 acres [29.5 sq mi (7,680 ha)] along Elk Creek, 18 mi (30 km) southeast of Covello, California. No mineral resources were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese and chromium. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

As far as is known at the present time, important ore occurrences at Mount Isa are restricted to the Urquhart Shale. These occur at Mount Isa itself, and some 13 miles north along strike at the Northern Leases.The primary silver-lead-zinc and copper orebodies occur as adjacent but discretc entities in lithologieally distinct host rocks. The copper orebodies occur in an envelope of "Silica Dolomite", whereas the silver-lead zinc orebodies occur in shale typical of the Urquhart Shale in general.At both Mount Isa and the Northern Leases, secondary lead orebodies occur at thc surface representing primary stratiform silver-lead-zinc sulphide accumulations in the fresh rocks at depth.Secondary copper orebodies are known only at Mount Isa, where they have formed in favourable environments, but unlike the secondary lead orebodies, not in the positions of the former primary mineralization that gave rise to them. The secondary copper is localized in shale remote from the point where the copper was released into solution by weathering. It was derived from very low grade fracture fillings and disseminations of chalcopyrite in the outcropping or suboutcropping crest of the "Silica Dolomite".Primary silver-lead-zinc orebodies arc oxidized without significant transport or secondary enrichment, but secondary copper orebodies arc characterized by considerable transport and extreme secondary enrichment.The original water table stood at approximately 1,150 ft (mine datum) and for the majority of the mine area controlled the base of complete oxidation fairly closely.An oxidized zone approximately 175 ft deep is general in the Urquhart Shale.Structures affecting ground conditions have influenced oxidation and leaching of the silver-lcad-zinc orebodies, and have had effects vital to the formation of secondary copper orebodies.

Jan 1, 1966

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By K Gordon

A methodology for assessment and remediation of acid mine drainage (AMD) developed at the Sullivan Mine in the West Coast Region has been applied to the closed Blackball Mine, Blackball, West Coast Region. AMD from the Blackball Mine has low pH, high acidity, and elevated levels of iron, aluminium, manganese, nickel, zinc and arsenic. The AMD flows at a variable rate (36 - 101 L/s) into adjacent Ford Creek, causing an increase in acidity and trace element concentrations in the creek. To test the effectiveness of treatment with a simple limestone-based treatment system, a column leaching experiment was conducted over a nine day period. The results show effective removal of acidity, reduction in the concentrations of iron, aluminium, manganese and zinc, and production of alkalinity. To determine if this treatment method reduces the toxicity of the AMD to aquatic invertebrates, a 96 hour ecotoxicity experiment was conducted. The results show a significant decrease in mortality in the treated AMD compared to untreated. The column experiment, in conjunction with the ecotoxicity work, suggest that a passive treatment system consisting of a limestone leaching bed and an open limestone channel may be sufficient to treat the AMD from the Blackball Mine. Further work, such as large-scale treatment trials, is recommended.

Jan 1, 2004

By A. Monomakhoff

If a conductor traversed by an electric current is broken, a conduction forms in the air between the two broken ends of the wire. This conduction manifests itself in an initial phase by an electric spark and, in a second phase, by an arc if the the circuit continues to supply sufficient power. This arc goes out when the distance between the two ends of the conductor becomes sufficiently large. If the break occurs in an explosive atmosphere, the energy contributed by the arc can cause an explosion. To avoid such accidents, electric circuits that may be utilized in hazardous atmospheres can be made "intrinsically safe". The investigation which we conducted is part of a research project on the intrinsic safety of arcs of high intensity but short duration, in the case of resistive circuits. We developed an electronic system which makes it possible to limit the duration of an arc at the level of the break of a conductor traversed by a current with a possible maximum intensity of 80 amperes. This experimental device for monitoring and measuring the parameters of the arc has shown that arcs of high intensity but with a duration limited to a few microseconds do not ignite an explosive methane-air mixture.

Jan 1, 1975

By D Preedy, J K. Claflin, S R. J La Brooy

This paper summarises the lessons learned during a recent carbon reactivation kiln upgrade project at the Sukari Gold Mine in Egypt. The kiln is being replaced to ensure that the plant achieves full value from the current throughput expansion from 5 to 10 Mt/a.The suitability of the original engineering design criteria for kiln selection and the adequacy of the original kiln are reviewed in the light of the carbon chemistry, operating experience and a site inspection of the kiln. Particular aspects of the reactivation facility are discussed including: predrying, preheating, feeding, gas seals, kiln heat transfer, steam injection, counter-current sweep gas flow, carbon cooling, fines minimisation and removal.Design criteria for a carbon predryer, reactivation kiln and cooler combination for carbon heavily fouled by high molecular weight frothers and collectors are discussed and the abridged Ausenco datasheet for the combination is presented.Responses to a request for a budget price sent to most of the worldÆs suppliers of carbon regeneration kilns are summarised.CITATION:Claflin, J K, La Brooy, S R J and Preedy, D, 2013. Ausenco carbon reactivation design criteria, in Proceedings World Gold 2013 , pp 401-410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Vasconcelos, X D. Deng

Numerous supergene manganese oxide deposits are developed inSouth China as a result of weathering of a thick sequence of Paleozoic marine Mn-bearing sedimentary rocks, consisting mainly of limestones, cherts and black shales that were intensely folded and faulted due to multiple episodes of tectonism since the late Triassic. The ore minerals are dominantly pyrolusite, cryptomelane, nsutite, lithiophorite and braunite. The supergene manganese ores contain Mn ranging from 20 to 44 wt per cent; manganese oxide deposits derived from cherts and black shales also contain recoverable levels of Co, Ni, Cu, Pb and Zn. 40Ar/39Ar dating of potassium-bearing manganese oxides reveals that extensive supergene manganese ore formation started at least in the earliest Miocene and persisted to the Present. Ages of the deposits show a close correlation to tectonic stability, with the oldest in tectonically quiescent areas and the youngest in active areas that have subjected to continuous uplift and thus significant denudation. The prolonged wet and hot climate since Oligocene and the balance between weathering and erosion, which is parameter to the tectonic stability, are the ultimate controls on the formation and distribution of South China supergene manganese oxide deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Luis Angel De Montreuil

Ante el problema del tratamiento de minerales complejos, la demanda de eficiencia metalúrgica y bajos costos de operación, el ingeniero busca el apoyo de la mineragrafía como estudio microscópico de los minerales económicos. En ese sentido, el presente texto señala la importancia de la minegrafía -en tanto ayuda a la flotación de los sulfuros valiosos de los yacimientos peruanos. Asimismo determina las propiedades de los minerales con el fin de identificarlos.

Jan 1, 1986

By Rob Famlield, Gavin Yuill, William Birch

The Blasting Research Group at the University of Leeds, in the United Kingdom, continues to be highly active in the area of the environmental impact of blasting. In recent years a major part of this research has been concerned with the use of linear superposition. This technique relies upon the assumption that all the holes in a blast produce identical vibration signals. Previous work at the University has shown that this assumption is not sufficiently robust to be generally applicable. This is due to a number of factors of which the key variable appears to be dynamic confinement

Jan 1, 2002

By Ubaldo Marques Silva Filho

Dentro da estratégia de investimentos da CSN para a Usina Presidente Vargas - UPV - a construção de uma unidade produtiva de aços longos com capacidade de 500 mil toneladas/ano está em processo de conclusão. Entre os vários processos existentes na unidade, a logística interna de movimentação de metálicos (sucata e gusa sólido) e o abastecimento da Aciaria Elétrica com cestões, são processos que se não estiverem bem configurados podem restringir as capacidades produtivas almejadas, comprometendo o alcance das metas estratégicas. Para analisar os possíveis impactos e restrições a produção, foi desenvolvido um modelo matemático em computador para simular as operações virtualmente, como forma de determinar as melhores condições operacionais e prever quaisquer gargalos no sistema.

Jul 29, 2018

By Walter Luiz Castro dos Santos, Leandro Resinentti Zanon

In the production of iron ore pellets, one of the factors that strongly influence the cost of ore-pellet processing is the specific consumption of natural gas that occurs during the thermal processing stage of the pellets. The filtration process is the step where the adequacy of the moisture percentage of the retained pulp occurs, so that subsequently there is the processing in the subsequent stages of the pellet formation and hardening of pellets. The water contained in the raw pellet is withdrawn at the stage of thermal processing. For this purpose, the literature indicates the demand of 600 Kcal/kg of water for the heating and vaporization of the moisture of raw pellets. The statistical analysis of the performance data of a pelletizing plant showed that for each decrement of 0.1% of water in the retained pulp is equivalent to the reduction of 0.091 Nm3 in the consumption of natural gas per tonne of pellets produced. Thus, the proper performance of the filtration stage is essential to reduce the percentage of pulp moisture retained and consequently to increase the energy efficiency of the pelletizing furnaces. The aim of this article is to present the main steps in conducting a work to increase the filtration performance to reduce the percentage of retained pulp moisture and the positive impacts on the specific natural gas consumption of a plant Pelletizing.

Oct 1, 2019

By AIME AIME

AN unusually interesting meeting devoted to the discussion of the ways and means of improving coal mining practice, through the larger use of machinery underground, was held in the Auditorium of the Engineering Societies Building on March 11. The meeting was organized by the Materials Handling Division of the A. S. M. E. and held under the auspices of the Metropolitan Section of that Society and the National Coal Association. The New York Section of the A. I. M. E., which had been invited to participate, found itself unable to do so formally because of a conflicting date for its March meeting but informally did its part to aasure the success of the meeting. As a result of the discussion at and preceding the meeting, the National Coal Association, through Walter Barnum, chairman of its research committee, has asked the A. S. M. E. and A. I. M. E. to join the Association in a study of the present problems of the bituminous coal industry. Messrs. Harry L. Gandy, Calvin W. Rice and H. Foster Bain have been selected to act as a committee which shall develop plans for a joint program.

Jan 1, 1926

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001