Search Documents

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By Oliver Hall

This paper sketches the mining at Noranda as it would be sketched to a visiting engineer. It does not follow quite the usual form, but is presented somewhat along the lines of a conversation. TO give the mining at Noranda its proper perspective, it is necessary to sketch the whole picture and outline: 1. History 2. Metallurgical Problems 3. Exploration 4. Mining Methods 5. Mining Details 6. Filling 7. Pillar Extraction 8. Costs HISTORY Noranda is a relatively young enterprise, with much of the personal character of its founders woven into it. The name Noranda is an abbreviation of Northern Canada and the name has been a happy one for an enterprise based on northern resources, tenacity and courage. The discovery credit goes to Ed. H. Horne. This intrepid prospector returned again and again to his sulphide discoveries on the shores of Osisko lake and, in 1922, after ten years of prospecting, succeeded in interesting S. C. Thomson and H. W. Chadbourne in his discoveries. The early exploration by L. K. Fletcher, from 1922 to 1925, for Thomson and Chadbourne, indicated promising, but somewhat perplexing, ore conditions. Mr. E. Hibbert and Mr. H. L. Roscoe rook on the task of preparing the mine for production and building a smelter in 1926, and this difficult task in this isolated area made steady progress and the smelter was blown-in in December, 1927.

Jan 1, 1937

By Vitor Tomaz de Aquino, Moysés Dutra da Silva, Weslley Luiz da Silva Assis, Rafael Masulck Santos, Tiago Araújo Neves

Neste trabalho é abordado o problema das múltiplas mochilas para modelar a necessidade industrial metalúrgica de alocação de bobinas de aço em um forno de recozimento em caixa. Condições especiais de processo, exigem priorização das bobinas mais antigas do estoque para garantir requisitos de qualidade. Além do mais, algumas limitações físicas e exigências de qualidade devem ser respeitadas, tais como, a obrigatoriedade de agrupamento de bobinas de mesma qualidade e limites físicos de altura e peso. Assim, uma formulação matemática é proposta para resolver este problema, cuja função objetivo visa maximizar o peso total da carga ocupada pelas bobinas de mesmas características e priorizar as bobinas mais antigas em estoque. Os resultados computacionais mostram que a aplicação da técnica do modelo de programação linear otimiza a formação de cargas gerando resultados reais de processo.

Oct 1, 2019

By Hayel M. El-Naggar, Sherif A. Akl

Although grouted piles have been used for several decades since the idea was proposed in the 1970s, their design is mostly based on experience and unpublished proprietary methods. There is little research on grouting drilled shaft tips and even less on grouting shaft sides. This paper presents the analysis of 4 instrumented pile loads tests on base and shaft grouted piles from different sites in Egypt; with emphasis on one of the tests, to demonstrate the analysis process. The data from the tests are analyzed to model the development of unit side friction (USF) with relative displacement. A numerical model using the finite element software PLAXIS is used to investigate the effect of grouting on the surrounding soil stress state. The paper combines the observations from full scale pile load tests and results from the numerical model to suggest an idealized behavior of side friction development with relative displacement of the grouted part of the shaft. The suggested model considers an envelope of Unit Side Friction (USF) with relative displacement, initially dominated by the grout resistance then at higher relative displacements, the friction with radially pressured soil takes over. The grout provides very high USF values up to a relative displacement of 2mm. Then, the USF drops to a typical pile soil side friction behavior; however, this friction is affected by the contact stress between pile and soil, which significantly increases due to compaction grouting. INTRODUCTION Base and shaft pile grouting has been significantly developing in recent years to accommodate the unfavorable conditions in major projects such as the high loads in high rise building and founding on problematic soil formations. Grouting aims to decrease settlements and increase the capacity of the pile under axial load. The technique is first introduced by Kraft (1974) but gained popularity in the 1980s. Typically there are two types of grouting; compaction, and permeation. Compaction grouting is more common in pile foundations practice, and many researchers have provided case histories of pile load tests on base grouted piles and base and shaft grouted piles (Gouvenot and Gabaix,1975; Stocker, 1983; Ghazali et al., 1988; Fleming, 1993; Kusakabe et al., 1994; Robson and Wahby,1994; Joer and Randolph, 1998; Hamza and Leoni, 1998; Mullins et al. 2000; Littlechild et al., 2000; Suckling and Eager, 2001; Dapp and Mullins, 2002; Ho, 2003; Fu and Zhou, 2003; Brettmann and NeSmith, 2005; Ruiz, 2005; Mullins, 2006; Dapp and Brown, 2010; Beadman et al., 2012; Nguyen et al., 2013; Miller et al., 2013; Sinnreich and Simpson, 2015; Hui and Lin, 2015). Compaction grouting is meant to densify the soil around the pile and below the base rather than permeate this soil and increase its cohesion. Research showed that grouting increases the capacity of the piles by a factor of 2~5. The variation in capacity increase depends on pile type, grouting process, and especially grouting pressure. Although there are many case histories of pile load tests on grouted piles but there is no well-defined agreed-upon method to predict grouted pile capacity as typically done in ungrouted piles. Few lab experiments discussed the shaft grouting effects on the soil especially the compaction grouting. The experiments concluded that the compaction grouting forms a homogeneous layer between the pile and the soil, and a residual effective stress is achieved simultaneously with a significant densification of the soil around the pile with noticeable decreasing in void ratio. (Fattahpour et al., 2015; Wang et al., 2015). Recently, studies used numerical analysis to investigate the behavior of the grouted piles and the changes in the surrounding soil (Chiang et al., 2013). That study presents a simulation of the base pressure grouting with a simple FE model and predicts the reduction of the pile settlement by 10 to 20%. Another numerical study using a complex model conducted by Zhou et al. (2017), pr

Jan 1, 2018

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

By Karl Marquis

La Mine Mouska exploite depuis deux ans certains blocs de réserve à l?aide de la méthode long trou. Même si, à priori, la méthode long trou semble rentable, le contrôle de la dilution ainsi que le respect d?un échéancier serré s?avèrent primordiaux afin que cette méthode d?exploitation puisse être justifiable économiquement. La présentation suivante fera la comparaison économique entre cette méthode et celle de chambre-magasin.

Oct 1, 2001

By Georgios N. Anastassakis, Nickolaos Georgiou

"Soil contamination by oil as well as by other organic pollutants poses a major problem to the environment. Various methods have been used to remove organic contaminants from soil, such as: biological, thermal, chemical and physical. Methods based on Mineral Processing principles have also been used (cyclone separation, gravimetric separation, attritioning and washing). This paper studies the possibility to remove a rich-in-contaminant soil fraction by applying flotation. The contaminated soil was artificially prepared by mixing soil with diesel fuel. Sodium dodecylsulfate (SDS) and a tertiary amine (TA) were used as collectors. The effect of collector quantity added and conditioning time was studied. The results showed that the removal of a rich-in-contaminant soil is feasible while a clean fraction is also obtained. In several cases, the removal of oil-contaminated soil approaches or reaches 100%. Introduction Human activities are intimately associated with environmental pollution to the air, water and soil, as well. Soil pollution from inorganic and organic compounds is of equal importance with that of air and water, as it results in soil degradation and its concomitant problems with respect to meeting the human needs (house building, agriculture etc). Heavy metals along with their compounds are encountered among the most usual soil inorganic pollutants. The corresponding organic soil-pollutants are oil, oil-derivatives, pesticides, various aromatic (benzene, phenols, cresols, toluene etc) and poly-aromatic (naphthalene, anthracene etc) hydrocarbons, as well as various other organic compounds (pyridine, cyclo-hexane etc). Oil remains the basic energy source sharing 38% of the global needs, being followed by coal and gas with a share of 26 and 21% correspondingly [1]. The entire activities related with oil production, transport and consumption promote pollution in the air, water and soil. Consequently, soil pollution from oil is favoured at refineries, storage sites (due to possible pipe and tank leakage, tank cleaning works, loading and transportation) and, finally, at the oil-selling sites. Oil (or diesel-oil) fuel is a mixture of hydrocarbons, with 10-20 carbon atoms in the chain of each. It is mainly composed of paraffins, naphthenes and various aromatic compounds. In general, oil is composed of 20-30% in aromatic compounds, 5-6% in naphthenes and the rest is paraffins [1]."

Jan 1, 2008

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J. Hines

Traditionally, fuel oil or diesel was the collector of choice in coal flotation, but in recent years these materials have come under increased scrutiny because of concerns about the toxicity of some components. In response to these concerns, Georgia-Pacific Chemicals LLC has commercialized a patent pending coal collector (Talon® 9400 reagent) that is 100% derived from the pulping of trees. This study presents a comparison of yields and recoveries for different coal collectors, including the one derived from the pulping of trees.

Jan 1, 2011

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By Thomas Kuhn, Carsten Ruehlemann, Christina Heller, Anna Wegorzewski

The commercial extraction of metals from manganese nodules on an industrial scale requires more than 50% of the investment necessary to realize manganese nodule mining. This is mainly due to the fact that a completely new metallurgical processing scheme for the extraction of both base metals (Ni, Cu, Co) and high-tech metals (Mo, Li, Ga) has to be developed and upgraded to industrial scale. There are a number of conventional processing technologies that combine hydro- and pyro-metallurgical approaches such as the INCO and CUPRION processes which have been developed in the 1970s and 1980s. Today, new approaches based on selective leaching with chelating agents and bioleaching try to minimize energy consumption and waste production. All of these extraction methods require knowledge how the metals are structurally bound in the manganese oxides. In this contribution we will review the current knowledge about the mineralogy of iron and manganese minerals in the different marine oxide deposits, present our results, and discuss the possible consequences for metal extraction.

Sep 1, 2014

By Roshan B. Bhappu, Zeki M. Dogan

Two magnesite ores containing 3.15% and 8.73% SiO2 and a calcined magnesite product assaying 2.6% Si02 were first reduced in size to -20 mesh by roll crushing. 'They were then treated dry on a high intensity magnetic separator to reduce their silica content by rejecting iron-stained silicate minerals in the magnetic fraction and obtaining marketable magnesite or calcined magnesite as a nonmagnetic product.

Jan 1, 1975

This paper is a collection of thoughts and frameworks. It addresses a simple question: æIf we are to believe the large number of people and institutions indicating that humans are destroying the Earth and that the end is nigh, why do we bother trying to be sustainable?Æ The paper lays out evidence for the existence of multiple hazards to global society. The existence of a hazard alone is insufficient to make an assessment of risk. Risk estimates are required to support decision-making. An approach to assessing risk is provided and some limited data are presented. A new ædefinitionÆ or statement of what sustainability (in a broad sense) might have become is then given. A decision framework for guiding decision- making about the risks is developed. This framework includes a definition of leadership with inherent implications for what determines whether a leadership position by title is actually leading. The paper concludes by offering a view of minerals industry sustainability and considerations around maturity in the current economic situation. It is hoped that by placing this collection of frameworks around sustainability, a supporting structure emerges that will facilitate action. It is proposed that action taken in this way will be more effective than reaction to regulation or even social license to operate imperatives because it is driven by a more holistic view of the challenges and the potential roles of individuals û all of whom are potential leaders at some scale of action.

Jan 1, 2009

By Leticia dos Santos Aguilera

Nanopartículas magnéticas são amplamente empregadas em diversas áreas devido as suas propriedades superparamagnéticas, e vem sendo estudadas por todo o mundo com potencial em campos como biomedicina e tratamento de efluentes. Nesse experimento as propriedades de ferritas mistas de manganês e zinco foram testadas e avaliadas com base na sua concentração de zinco em cada composto, usando como fator de comparação suas velocidades médias de arraste em um tanque de ondas graduado na presença de um campo magnético externo. O processo procura viabilizar um método de análise que sugira possível coerência com resultados observados em outro método de caracterização magnética, a magnetometria por amostra vibrante. Tais resultados apresentaram maior magnetização de saturação para as amostras de Mn0,5Zn0,5Fe2O4 assim como foi observado maior velocidade de arraste nas amostras de mesma estequiometria.

Oct 30, 2017