Search Documents

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

By Howard N. Eavenson

AN analysis of the bituminous coal situation by an authority who traces the production, mining, safety, markets and labor trends in comparison with other fuels. BEFORE 1918 the production of coal experienced a steady growth, with slight recessions in ouput in only twelve years (1837, 1841, 1852, 1855, 1861, 1874, 1876, 1889, 1894, 1905, 1909, 1914), and in each of these cases the loss was recovered in the following year and the increase continued. In each decade the output was doubled. Prices, while not high, allowed some profit. In 1918 during World War I, an output of 580 million tons was reached and with the exception of 1923 this total was not again reached until 1942, in World War 11. Losses of output in this period were much greater than ever before; in 1932 the total was 270 million tons less than in 1918 or 1923, and the loss after 1923 was not recovered until 1942. The greatest output was 631 million tons in 1947.

Jan 1, 1950

By A. D. Hammond

"The drop in iron ore prices has claimed an unwitting casualty in vanadium. Vanadium is dominantly produced as a coproduct of steel production. The recent shutdown at EVRAZ’s Mapochs steel-vanadium operations in South Africa has cut off 10 percent of the world’s vanadium output. In February 2015, Australia’s Atlantic Ltd. suspended operations at its Windimurra iron-vanadium complex after a fire caused severe damage at the plant. Since then, challenging market conditions has resulted in the permanent closure of this operation.This decoupling of vanadium production from integrated iron ore producers presents an opportunity for vanadium exploration companies to target single-product deposits. This trend is manifested in the increasing number of pure-play vanadium ventures around the world.The mine production of vanadium is dominated by three countries — China, South Africa and Russia, which collectively produce 96 percent of the world’s vanadium. While the use of vanadium as an alloy in the steel industry remains the largest application for this metal, growth in demand is expected to come from the renewable energy industry in the form of batteries for energy storage.This article summarizes the current state of vanadium exploration, briefly describes the vanadium market and lists sources of future demand for the metal.Trend in vanadium explorationThe most active participants in the current vanadium exploration are pure-play vanadium ventures in Brazil, South Africa and Australia. These ventures are targeting deposits with higher vanadium grades than those typically mined in titaniferous magnetite operated by integrated steel-vanadium producers.The 10 percent shortfall in vanadium production resulting from the shutdown at EVRAZ’s Mapochs is expected to be partially compensated by Largo Resources’ Maracás Menchen vanadium operation located in the state of Bahia in Brazil. It commenced operation in August 2014 and is expected to produce between 7.6 and 8.6 kt (8,421 and 9,523 st) of V2O5 in 2016 at a target production cost of $3.71/lb (Largo Resources, 2016). This is the first primary vanadium operation to be placed in production in the Western Hemisphere in more than 35 years."

Jul 1, 2016

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller:5 Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone.

Jan 1, 1931

The use of walk-through inspections, approvals and ad hoc investigations to ensure risk is kept within acceptable levels is reaching its limits of effectiveness. Further improvement in occupational health and safety requires a systems approach, and the use of Quality Management principles is an obvious basis for this. SafeGuard, a æbest practiceÆ model health and safety management system and audit criteria based on AS/NZS ISO 9001:1994, has been produced by the Department of Mines and Energy. Quality style audits of mine and quarry health and safety systems are now being carried out by the Inspectorate.

Jan 1, 1998

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By James J. Tansey

A Deep Foundations Institute meeting with the University of Michigan at Ann Arbor in March of 1984 featured legal rights under Differing Site Conditions. A workshop conducted by the authors and Gerard Ittig, Esq. added to the value of the symposium. This paper will be of interest to your attorneys in any subsurface disputes.

Jan 1, 1985

By Sri C. Sawmliana, P. Pall Roy

Damage to underground roof and pillars in blasting gallery (BG) panels has been an increasingly important area of study in recent years due to the invention of new explosives and cord systems which has led to the modification and alteration of the design aspects developed by Charbonnage de France (CdF). According to extensive mine experiments conducted by Indian and foreign experts, it has been established that the induced peak particle velocity (PPV) is predominantly related to the emanated seismic energy of a source and the distance from the source. With that concept in mind, nearly 160 experimental blasts were carried out in four BG panels in India under varying geomining conditions. Based on the results obtained thus far, the authors have established predictor equations correlating explosive energy (in Joules) and distance from the shot to that of induced peak particle velocity received at the sensor point. Good correlation was obtained between the actual and the predicted values. It is realized that this equation may be used as an efficient tool to determine the size limit of blasts in BG panels so that the induced particle velocity does not create damage in underground workings as per the established Blast Damage Index (BDI) and other available safety norms.

Jan 1, 2004

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

By D Tuazon, M Powell, M Ziemski, G D. Corder

Although mining companies have made broad corporate-level commitments to adopt sustainability, there continue to be problems when attempts are made to adopt higher-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies, yet impacts from operational decisions can have longer-term effects realised at closure and rehabilitation.This paper describes a proposed methodology to achieve the integration of sustainability at the operational level through a systematic and rigorous process of identifying and qualifying sustainability issues and opportunities in an operation. The methodology, starting from a sustainability point of view rather than an operational one, guides the identification of process issues and opportunities by examining the operation, unit-by-unit, similar to a Hazard and Operability (HAZOP) process. Each issue or opportunity is qualified according to its measurability, scopes of impact and consequences so that it may be understood fully and the correct engineering problems are formed. Through improved decision-making to account for broader sustainability factors, operations can better address environmental and social expectations and pressures (both corporate and community, as well as immediate and in the longer-term), whilst still delivering on operational and business goals.The methodology has been tested with two case studies at minerals processing operations. At one site, the methodology identified a dust issue which had considerable business risks (loss of valuable product) compared to conventional engineering analysis processes. The other site also benefited from using the methodology as an opportunity to improve the operation of the milling and flotation circuits was identified. The opportunity not only showed a potential to improve operational efficiency, but also potential improvements in water and energy efficiency and a resulting increased resilience against water and energy supply risks. It was important to utilise the holistic approach of the methodology in the identification of opportunities at this site; the goals of the operation showed a strong coupling between water and energy issues which would be difficult to overcome using the operationÆs current organisational model, which deals with such issues separately of each other.CITATION:Tuazon, D, Corder, G D, Powell, M and Ziemski, M, 2012. A practical and rigorous approach for integrating sustainability principles into decision-making processes at minerals processing operations, in Proceedings Life-of-Mine 2012 , pp 233-242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By Changping Hu, Keqin Tan

In 1937, the Metallurgical Department of the National Resources Committee established a copper refinery plant (predecessor of the Chongqing Smelter) in Changsha, Hunan Province, China. The blister copper produced by a local copper smelter was casted as anode for electrorefining. The plant, with a capacity of one ton of electrolytic copper per day, was designed and tested in 1937. At the trial production stage, a total of 9 tons of cathode copper was produced. The plant was formally put into operation in July 1938. In the same month, more than 20 tons of electrolytic copper with purity over 99.9%Cu was produced. This was the first batch of electrolytic copper produced in China. In 1939, China’s largest non-ferrous metal smelting plant, Fengtian Gold Mine Refining (predecessor of the Shenyang smelter) was completed and put into operation in Shenyang, mainly producing nonferrous metals such as gold and silver, as well as copper and lead. In 1939, the Kunming copper smelter (predecessor of Yunnan Smelter) was completed and put into operation. The plant equipment, imported from the United Kingdom, was designed to produce 1,200 tons of electrolytic copper annually. In 1943, Jiatong smelter (predecessor of the Shanghai Smelter) became the 4th domestic cathode copper producer. Since 1949, China has gradually established a large copper industry. These developments are discussed in this paper. Today, China operates nine out of the twenty largest copper refineries in the world. With a total capacity approaching 9 million tons of copper per year, China has the world’s largest copper refining capacity. INTRODUCTION China is a country with a long history of copper mining. The earliest smelter in China in recent times was the Shanghai Smelter, which was built in 1912. From then until 1949, China successively built Chongqing Smelter, Kunming Smelter and Shenyang Smelter. The world's first copper electrorefinery was the Pembrey refinery built in the UK in 1869 (Lu, 1999). However, it was not until 69 years later that the technology was spread to Changsha, China.

Jan 1, 2019

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009

By J L. Carpenter, S M. Iveson, K P. Galvin

Wet beneficiation of iron ore fines less than 1 mm typically involves a desliming stage ahead of the fine gravity separation such as spirals. The desliming is achieved using a bank of cyclones. The reject ultra-fines emerge in the overflow stream at relatively low pulp density, contain high proportions of low-value slimes, but also well-liberated iron ore ultra-fines below 0.045 mm in size; however, recovering the valuable iron ore ultra-fines from this overflow stream presents a significant challenge due to the need to remove such a large amount of water and slimes.The REFLUX™ Graviton consists of distinct 3D-printed modular units, based on REFLUX™ Classifiers, which are rotated at high speed in a large centrifuge. This system has previously been investigated under semi-batch conditions, demonstrating the potential for precision separations with significant capacity. It has been shown that the throughput advantage of the inclined channels and G forces multiply. This is the first paper presented showing the performance of this system under continuous steady-state conditions. Ultra-fine silica in the size range of 0 to 0.045 mm was fed to the Graviton at different volumetric rates, fluidisation rates and pulp densities ranging from 2 wt per cent to 30 wt per cent, in order to develop a fundamental understanding of the system’s performance. Experiments were then repeated using ultra-fine iron ore.CITATION:Carpenter, J L, Iveson, S M and Galvin, K P, 2017. Separation of ultra-fine particles using the REFLUX™ Graviton, in Proceedings Iron Ore 2017, pp 141–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Jorge Lucas Carvalho Bechir

A usina de beneficiamento da Unidade Vazante da Votorantim Metais concentra zinco a partir de Willemita – Zn2SiO4 por flotação. Através desse processo, é possível obter elevadas recuperações metalúrgicas. Contudo, foi identificado que é possível aumentar ainda mais a recuperação de zinco através de redução de granulometria. Essa redução eleva os custos de energia de um circuito de cominuição, fato que torna fundamental a identificação da relação ideal entre ganho de recuperação e os gastos com maior consumo de energia. Grande parte das frações de Willemita mais grosseiras (acima de 0,15 mm) que passam pelo processo de flotação, vão para o rejeito. Isso ocorre devido a granulometria atual de moagem não atingir a liberação ideal do mineral de interesse, de forma que, grande parte da superfície das partículas ainda apresenta ganga que não é adsorvida pelo coletor especifico da Willemita. Em busca de elevar a recuperação metálica de zinco potencializando o seu aproveitamento, estudos de caracterização mineralógica foram realizados. O trabalho consistiu na utilização de MEV/EDS com MLA (Mineral Liberation Analyzer) e na realização de testes de flotação em escala de bancada e piloto para determinar a granulometria ideal para flotação do mineral Willemita. Através dos resultados obtidos, foi possível concluir que houve ganhos de recuperação de zinco com a redução da granulometria sem comprometer a qualidade do concentrado gerado.

Aug 17, 2017