Search Documents

By John G. Parker

The rare-earth elements, sometimes known as the lanthanides, comprise the series of 15 chemically similar elements with atomic numbers 57 through 71. Yttrium, with atomic number 39, is often included in the group, because its properties are similar and it more often than not occurs in association with the lanthanides. Thorium is included in this survey due to its close association with the lanthanides, particularly in the mineral monazite. The lanthanides were first recognized as elements around 1750 and were the subject of much study by chemists during the 19th century. The purely chemical methods then available failed to resolve the strange intimate relationships between these elements, and it was not until about 1920 that the full series was explained.

Jan 1, 1971

By Paulo Sérgio Moreira, Geraldo Lúcio de Faria, Rhelman Rossano Urzêdo Queiróz, Amanda Aparecida Fátima Arruda, Ana Cecília de Carvalho

O objetivo deste trabalho foi avaliar o desempenho em desgaste de camadas espessas de óxidos formadas na superfície do aço inoxidável ferrítico 410D após a sua submissão a tratamentos isotérmicos em atmosfera oxidante. O aço em questão foi estudado no estado de entrega e tratado isotermicamente nas temperaturas de 900°C e 1000°C por diferentes intervalos de tempo. O método de avaliação empregado foi o teste de desgaste micro-abrasivo do tipo esfera presa em placa. Com o desenvolvimento do estudo, foi possível executar análises qualitativas e quantitativas a respeito do comportamento em desgaste do aço inoxidável 410D em função de sua condição superficial, como oxidada ou não. Alterações microestruturais também foram consideradas na discussão dos resultados. Concluiu-se que a camada superficial de óxidos desenvolvida após os tratamentos isotérmicos possui boa aderência e tem potencial para aplicação como camada protetora do aço em aplicações onde a sua resistência ao desgaste seja requerida.

Oct 9, 2019

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By Hormando Leocadio Júnior

A otimização operacional no setor de desbaste da Linha de Tiras a Quente da Usiminas, Ipatinga, proporcionou redução do tempo de processamento dessa etapa, criando-se condições para aumento das temperaturas dos esboços na entrada do Trem Acabador (TA). Desse modo, para manutenção das temperaturas de acabamento dos laminados dentro da faixa de controle desejada, seriam necessárias menores velocidades de laminação no TA. Com a finalidade de garantir temperaturas desejadas na entrada do TA, que possibilitem adequadas velocidades, foi desenvolvido um sistema de controle de temperatura de esboço, que é acionado e desligado automaticamente na região inicial (topo), na extensão necessária do esboço. Esse sistema permitirá uma ampla exploração da nova condição de desbaste em menor tempo, com menor variabilidade da temperatura de entrada no TA, prevenindo ocorrências de estiramentos e de carepa, por temperatura alta nos topos e baixas nas bases dos laminados, maior uniformidade de propriedades mecânicas dos produtos, assim como aumento na capacidade produtiva.

Jul 30, 2018

By Luis Alberto Sfalsin Passos

Com o passar dos anos observa-se uma mudança nas características mineralógicas dos minérios de ferro lavrados nas novas minas da Samarco Mineração SA. De acordo com levantamentos podem ser constatadas mudanças nos percentuais da hematita porosa, hematita especular e da goethita na constituição do concentrado de minério de ferro. Pode-se verificar uma tendência de aumento do percentual de goethita bem como do PPC (perda por calcinação) característica intrínseca ao minério. Estes fatos implicam em uma maior dificuldade da concentração em garantir a qualidade da polpa de minério bombeada para as usinas de pelotização, visto que fatores como a granulometria do minério (partículas menores que 325#) e a superfície específica são afetadas pela mineralogia. Por consequência, há uma maior dificuldade no processo de filtragem para obtenção do pellet feed com a faixa de umidade necessária para o processo de pelotamento e queima. De outra forma, o aumento do PPC dificulta o processo de secagem das pelotas no forno de pelotização, exigindo um maior aporte térmico para retirada da água residual contida nos cristais que não evaporam a 100°C. Todos estes fatores contribuem para a qualidade da pelota queimada, interferindo na sua resistência física como compressão a frio e tamboramento. Esta pesquisa tem como objetivo apontar as variáveis que influenciam significativamente o tamboramento, para propor ações que melhorem o controle do processo produtivo de forma a buscar o ponto de equilíbrio entre qualidade e produção.

Aug 16, 2017

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

A homely simile will serve to epitomise an interpretation of the rock structures and associated phenomena of the block of country under review, as it appears to the writer.Disregarding the many thousands of feet of overburden that have been eroded away during the ages, the present denuded surface and rock systems below may be pictured as a slab of some titanie ribbon cake that has suffered much damage from rough handling and exposure, yet retaining much of the original symmetry of its superimposed layers of variegated colour and texture.Lateral pressure has crumpled the cake into a series of irregular corrugations and, in parts, has caused some of the layers to crush and slide over their neighbours.Following upon this squeeze, the cake has been severed into segments and rhomboidal slabs by vertical cuts, and these portions have been severely jostled one against its neighbour, crushing the faces of contact and dragging the contiguous layers in the direction of movement.The variegated icing of the cake is represented by intercalated sills of amphibolite, pegmatite, and aplite, and the body of the cake by highly altered sedimentary rocks.The icing has been assailed by the rats of erosion with such effect that only residuals of the original structures remain. The body of the cake has suffered successive waves of igneous invasion in the order of lode pegmatite, followed by zine, iron,copper, and finally by silver-lead. These successive invaders found difficult access, along certain of the vertical cuts, to the more succulent layers of the cake, where, gorging to repletion, many were imprisoned and entombed for the future service of mankind.

Jan 1, 1927

President John T. Atkins on behalf of The RMCMl officers and Executive Board, invites you and your family to attend The 80th Regular Meeting and Convention of 'The Rocky Mountain Coal Mining Institute to be held at Marriott's Mark Resort, Lionshead Village in Vail, Colorado JUNE 24 - JUNE 26, 1984

Jan 1, 1983

By Olav Mellgren

Part I. The interaction between potassium ethyl xanthate and lead salts has been studied thermo-chemically. It is shown that ethyl xanthate reacts with lead carbonate, basic carbonate, thiosulfate and sulfate according to principles of simple chemistry, whereas reactions with lead sulfite, metasulfite, basic thiosulfate and hydroxide at high pH are associated with secondary reactions. A new compound "xanthogen thiosulfate" is postulated. Part 11. Adsorption of ethyl xanthate on galena has been studied quantitatively and thennochemi-cally. It is shown that an ion-exchange mechanism governs the adsorption process and that the heat of adsorption of xanthate on galena is equivalent to the heat of reaction of ethyl xanthate with bulk lead salts. It is concluded that the entropy content of the surface "compound" on galena is different from that of a corresponding bulk lead salt. Alkali depression is in part shown to be due to the instability of the xanthate-galena system at high pH and to the formation of basic lead salts. Sulfate and carbonate ions are shown to have a stabilizing effect on the xanthate-galena system. PARTI. THERMOCHEMISTRY OF ETHYL XANTHATE AND OF ITS REACTION WITH LEAD SALTS In the past little attention has been paid to the chemistry of lead xanthate. It is known that xan-thates form slightly soluble compounds with lead and that suspensions of lead xanthates in alkaline solution decompose rather readily.' The solubility of lead ethyl xanthate is of the order of 2.6 x 10-6 moles per 1. At increasing pH the xanthate concentration of a saturated solution contains more xanthate. Thus at pH 11 this xanthate content is about 100-fold larger than at pH 7.1 Xanthates are known to be consumed when added to a suspension of slightly soluble lead salts such as lead sulfate and lead carbonate. It is unknown to what extent this xanthate consumption is due to a simple chemical reaction because, frequently, observations are made which reveal secondary reaction products in such reactions. Thermochemical study of the reaction between xanthate and lead salts offers a means to clarify the significance of these reactions as the enthalpy changes can be accurately predicted from heat of formation of lead salts in pure solution reactions. In the present work the heats of formation of lead ethyl xanthate from potassium ethyl xanthate and lead salts are determined and some thermochemical aspects of xanthate in solution are studied. The results of these investigations are presented in Part I. In Part II the heat of adsorption of ethyl xanthate on galena surfaces is presented. All enthalpy changes were measured directly in a microcalorimeter. Calorimeter: The calorimeter used for measuring enthalpy changes was similar to that used by Redinha and Kitchener2 which was based on a description by Derbyshire and Marshall.3 Other useful references4,5 are listed. A sketch of the calorimeter

Jan 1, 1967

By C. Dinis da Cama

In order to reduce the complexity of mechanisms influencing rock- fragmentation by blasting a simulation approach is proposed, using the capabilities of micro-computer interactive graphics. Situations involving cratering and bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By S. H. Badenhorst

Zacharias Lewala discovered a diamond at Grasplatz, near Lüderitz in April 1908. While this stone may not have been the first diamond to be found in this barren, inhospitable area, it most certainly was the stone that set off a chain reaction ultimately leading to the creation of Namdeb as we know it today. [ ]

Jan 1, 2003

By Z. Zhang, R. G. Reddy

Viscosities of industrial lead slags with various compositions were measured as a function of temperature using a Brookfield viscometer. Based on the experimental data from this study and other investigations reported in the literature, an expression has been developed to correlate the viscosities of lead silicate slags as functions of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of viscosity of lead silicate slags is discussed. The calculated results using this viscosity expression are in good agreement with the measured data.

Jan 1, 2001

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key aspect of mechanization is the optimization of equipment utilization, and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2007

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Leandro Brunholi Ramos

O aço API 5 CT P110 é amplamente utilizado no setor de petróleo e gás no Brasil devido sua elevada resistência mecânica, contudo ele não possui uma boa resistência a corrosão. Com a descoberta do pré-sal, novos desafios surgem neste setor, tornando necessário o desenvolvimento de novas tecnologias resistentes aos ambientes agressivos que os materiais serão expostos. A aspersão térmica por HVOF se destaca pela obtenção de revestimentos contra corrosão e resistentes ao desgaste com baixa porosidade e com um relativo baixo custo em comparação a outros processos. Dentre os materiais que podem ser aplicados como revestimentos por aspersão térmica, o níquel se destaca pela ótima resistência à corrosão por formar um óxido protetor na superfície. Sendo assim, o presente trabalho tem por objetivo obter e caracterizar revestimentos de níquel obtidos por aspersão térmica HVOF, no aço API 5CT P110. Os revestimentos foram caracterizados morfologicamente por microscopia eletrônica de varredura (MEV). Foram obtidas curvas de polarização para avaliar o comportamento frente à corrosão e foram realizados ensaios para determinação do coeficiente de atrito. A camada aspergida de níquel apresentou resultados satisfatórios quanto às análises estudadas.

Aug 8, 2018

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

By Richard D. Lang

Introduction Argyle is located in the Kimberley region in northwest Australia (Fig. 1). It is a significant diamond discovery by world standards and is the first major diamond find in Australia. The deposit consists of a pipe and associated alluvial deposits. Before the 1970s, diamonds were known to exist only sporadically in Australia. They have been found occasionally in association with gold deposits in Western Australia. There is a small deposit near Copeton in New South Wales. Some alluvial occurrences have also been found in Victoria, South Australia, and New South Wales. The first indicator minerals in the Kimberley region of Western Australia were discovered in January 1973. Production from the alluvial deposits at Argyle began in 1983. A $430-million construction program to develop a mine and treatment plant capable of producing 25 million carats per year was completed in December (1 carat = 0.2 grams). Ownership and management Participants in the project are known as the Argyle Diamond Mines Joint Venture. The group consists of CRA Ltd., 56.8%; Ashton Mining Ltd., 38.2%; and the Western Australian Diamond Trust (formerly Northern Mining Corp.), 5%. The project is managed by Argyle Diamond Mines Pty. Ltd., a wholly-owned subsidiary of CRA. Marketing is undertaken separately by the Western Australian Diamond Trust and by Argyle Diamond Sales Ltd. (for CRA and Ashton Mining groups). History Ownership of the Exploration Joint Venture has changed over the last 12 years as various parties changed their shareholdings. The original Kalumburu Joint Venture was formed in 1972 with five participants, each holding a 20% interest. By 1983, a number of ownership changes had occurred. The end result is that two original participants have sold out. CRA now holds a 56.8% share and the Ashton Mining Group holds 38.2%. CRA also assumed project management in January 1977. Table 1 demonstrates the long lead times involved in developing a project.

Jan 1, 1986

By King E. J

Department of Pathology, British Post-graduate Medical School, London:The experiments here recorded were devised and carried -out during the last two years in an attempt to corroborate the important work of Denny, Robson and Irwin (1939) in which they found that experimental silicosis could be prevented by means of metallic aluminum. By causing rabbits to inhale powdered quartz for several months they induced experimental silicosis. These animals then served as controls for comparison with another group which were dusted with a mixture of quartz and aluminum. In the second group silicosis failed to develop.Our experimental procedure was somewhat different. We resorted to intratracheal insufflation instead of simple inhalation, and we used rats instead of rabbits: otherwise the essential features of the original experiments were carefully duplicated.EXPERIMENTAL PROCEDURES.A single dose of dust was delivered into the lungs of each animal. The dust was suspended in a fluid medium and injected by means of a syringe directly into the trachea in known quantity (technique of Kettle and Hilton, 1932). The suspensions were autoclaved before use and were injected with aseptic precautions. Having had a long experience of this technique we employed it with confidence and usually secured a fairly uniform dispersal of dust throughout both lungs. To carry out injections successfully one requires, above all, an even suspension of dust which will flow smoothly and quickly from the syringe. This is not difficult in the case of quartz, for, though it tends to settle out rather quickly, this can be avoided by constantly agitating the suspension. The syringe containing the inoculum may be shaken gently right up to the moment of injection and then emptied quickly to prevent sedimentation. Powdered aluminum is more difficult to handle, for the particles tend to flocculate and are not readily made to disperse evenly in saline, even by violent shaking. For this reason an emulsifying agent may be used to advantage, provided it does not complicate the experiment, a point to be mentioned again presently.THE EXPERIMENTSExperiments with quartz alone: Extensive silicotic lesions were produced in 23 out of 26 rats by the administration of pure quartz dust in doses of from 50 to 200 mg. per rat. The dust was so finely pulverised that the particles averaged about 1-p. in size: none was larger than 5 p. and 99 per cent. were under 2.5 p.Eight of these animals survived for seven months and were then killed...

Jan 1, 1945