Search Documents

By N. D. L. Burger

A low noise blast hole drilling system was developed to limit the risk of noise-induced hearing impairment in mining operations. Noise- induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise-induced hearing loss. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard SecoS215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock debris, oil and grease) is removed from the encapsulating tubes via an exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2004

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By M Pizey, M Kingsbury

Since 1950 Stockton Open Cast Mine has excavated over 60 million tonnes of Brunner Coal Measures overburden sandstones and mudstones. The current operator, Solid Energy New Zealand, recognises that acidic drainage from this overburden and from historic underground mines has led to depressed pH levels and elevated levels of metals in streams draining the Stockton Plateau. These streams report to the Ngakawau River. To quantify the effects of mine site acid drainage remediation/mitigation on the lower Ngakawau River water quality, a catchment hydrogeochemical model has been field calibrated and ecotoxicology tests have been undertaken. The hydrogeochemical model indicates that pre-mining and present pH values in the lower Ngakawau River are similar but present aluminium and iron concentrations are elevated. Ecotoxicology tests have semi-quantified the critical metal concentrations and interim water quality targets to achieve ecological recovery are presented. Analyses of long-term total suspended solids (TSS) and turbidity monitoring in the lower Ngakawau River and St Patrick's Stream indicate that TSS of 120 mg/L and turbidity of 20 NTU are exceeded for <20% per cent of the time. Hence, specific criteria to protect migratory native fish from turbid water are currently met in the Ngakawau River and St Patrick's Stream.

Jan 1, 2003

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By S. Shi, J. Y. Hwang, B. Li

Silver, copper, and zinc are commonly known elements with antibacterial and antifungal capabilities. Attempts have been made to dope silver on minerals, glass, and ceramics and the resulting materials have been investigated for their antibacterial and antifungal properties. Since silver is expensive and very reactive, silver doped materials have been found inappropriate in some applications. Copper-vermiculite is investigated as an alternative. Vermiculite has high cation exchange capacity on the magnesium ion in the crystal structure. Copper ion may have a high tendency to replace magnesium because of similar charge interference and ionic radius. Copper-vermiculite is prepared by reacting vermiculite and copper chloride solution. By impregnating copper ions into the nanometer openings between the layers of vermiculite, it is possible to render the composite with antibacterial functions if the copper ions could be released gradually from the composite. The antibacterial efficiency of Cu-vermiculite against Escherichia coli was studied using the Halo method. The results show that Cu-vermiculite is effective for preventing the reproduction of the bacteria. Heat treatment of Cu-vermiculite at up to 400°C does not show significant changes in antibacterial activities.

Jan 1, 2002

By T. Adamcewicz

The province's lignite resources lie mainly in the south, extensions of the much larger deposits in Montana and North Dakota. Because of planned additional capacity, conventional steam power generation will probably remain as the dominant resource usage for many decades. Conversion of coal to other energy forms is receiving emphasis and in the future will compete with steam power generation in terms of quantities used.Economic deposits, minable by present-day technology, have been generally defined. Because a large percentage of the total lignite resource is in seams containing multiple partings, future extraction will become much more difficult and capital intensive.Increased public involvement will ensure that the impacts of future coal mining and usage operations are compatible with environmental and social objectives.

Jan 1, 1982

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

During the latter part of 1937 consideration was given to the construction of a; local smelting plant for producing blister copper. Previously copper concentrates had been shipped to the United States of America. The proposition had the advantages of a saving in cost of realization, quicker financial return and reduced dependence on overseas shipping.The smelter was designed by the existing staff, who had difficulty in obtaining data on small plants, particularly on the reverberatory furnace. Construction was started in March, 1938, and the reverberatory was blown in on January 16th, 1939. One roaster had been operating for several weeks prior to this date.While results and operating technique on this new departure in small-scale smelting are barely beyond the experimental stage, it is felt that the experience gained to this time should be recorded to help fill the obvious gap in published information covering plants of this type.At present there are three copper smelters operating in Australia; the other two plants are equipped with blast furnaces.LOCATIONThe new smelter is situated in a position convenient to the concentrator and to the power plant. The site is traversed on two sides by a brick flue, from an old smelter plant, which connects with a 250-ft. stack. This stack and portion of the old flue are used in connection with the...

Jan 1, 1939

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By Tim O’Neil

Dressed in black tie and Victorian attire, some 200 people came to Leadville, CO, for a September weekend featuring a National Mining Hall of Fame and Museum (NMHF&M) induction banquet and a scenic mountain train trip to Fremont Pass and the Climax Mine. The 18th annual induction banquet on Sept. 17 began with cocktails and a open house. It was a chance for visitors to tour the National Mining Museum including the new Hennebach Wing, opened in February. The new wing is named in honor of Ralph Hennebach, retired chairman of Asarco. Formerly Leadville Junior High School, the Hennebach Wing encompasses more than1,440 m2 (15,500 sq ft) of floor space in two stories. One prominent feature is a 1923 Wills Sainte Claire touring sedan. Climax Molybdenum donated this first all-molybdenum steel motorcar. Docents were available throughout the museum to give banquet attendees directions and answer questions.

Jan 1, 2005

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949