Search Documents

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

The ~2500 km long Kermadec-Tonga arc northeast ofNew Zealand is the longest continuous intraoceanic arc in the world. At least 94 volcanic centres along the arc are submarine, most (87 per cent) within the Kermadec arc (de Ronde et al, 2003a). Volcanic rocks range from basalt to rhyodacite with trace element and isotopic data indicating significant magma source heterogeneity both along and across the arc.   The entire ~1300 km of the Kermadec arc has now been surveyed for hydrothermal emissions (de Ronde et al, 2004). First-stage surveys utilised surface vessels. In February 1996, the first sulfide samples from the southern Kermadec arc were dredged from the Brothers and Rumble II West caldera volcanoes (R/V Tangaroa cruise TAN96/03; Wright et al, 1998; de Ronde et al, 2003b). In September 1998, low-temperature, diffuse venting was discovered at Monowai, Rumble III and Clark volcanoes, and high-temperature, black smoker venting was found within Brothers caldera (R/V Sonne cruise SO-135; Stoffers et al, 1999). The NZAPLUME cruise of March 1999 surveyed 13 volcanic centres (each mainly comprised of single, large volcanoes) of the southern Kermadec arc and documented hydrothermal emissions above seven of them (de Ronde et al, 2001; Baker et al, 2003; Massoth et al, 2003). In July 2001, additional mineralised and hydrothermally altered samples were dredged from Brothers volcano (R/V Tangaroa cruise TAN01/07). The NZAPLUME II cruise of May 2002 confirmed venting was still occurring at all the known hydrothermal sites, and that ten active vent sites occurred along the mid-part of the arc, between Brothers and Raoul Island (de Ronde et al, 2002). In September-October 2004, NZAPLUME III surveyed the northern-most part of the Kermadec arc where another nine volcanic centres are hydrothermally active.   Second-stage exploration of the Kermadec arc hydrothermal systems utilised deep submergence vehicles. In October-November 2004, the Japanese submersible Shinkai 6500 made four dives on Brothers. Samples recovered include vent fluids, chimneys, altered rocks and various animals and microbes. In April-May 2005, a more extensive expedition using the American submersible Pisces V made 23 dives on nine different volcanic centres, eight of them for the first time.   Extensive plume surveys show Brothers volcano is host to the most hydrothermally active sites of all those known along the Kermadec arc. In total, nine dives have been made on Brothers, six on the NW caldera site and three on the cone site. The NW caldera vent site is a long-term hydrothermal system that is today dominated by evolved seawater but has had episodic injections of magmatic fluid. The cone site is a nascent magmatic-hydrothermal system where crack zones localise upwelling acidic waters (de Ronde et al, 2005). A SE caldera site represents the main upflow of a relatively well-established magmatic-hydrothermal system on the seafloor where sulfide-rich chimneys are extant. Each of these different vent sites represent diverse parts of an evolving hydrothermal system, any one of which may be typical of submarine volcanic arcs.

Jan 1, 2005

By C. A. Gibbons

AFTER nine years of extremely de- pressed business, marked mostly A with red ink on the balance sheets of most coal companies and with an increasing internal competitive struggle for diminishing markets, somewhat of a change appeared during 1939. Shipments increased and prices generally firmed, giving the coal industry increasing optimism and encouragement for the future. Specifically, it now appears that bituminous coal production for 1939 will approximate 378,000,000 tons, and anthracite production will approximate 47,500,000 tons, bituminous production being around 14 per cent ahead of 1938 and anthracite production 12 per cent better. The curve on p. 31, showing both bituminous and anthracite production, furnished by the bituminous coal division of the Department of the Interior, shows graphically most of the 1939 monthly production and clearly illustrates the increased production.

Jan 1, 1940

THE following really forms the second part of, or a sequel to, a paper, " Ventilating Metalliferous Mines: a Method of Attack," read before the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy in May, 1920. In that paper the writer advocated a consideration of the question of ventilation in metal mines from a different aspect to that 'which had hitherto prevailed locally. Various factors regarded as having an important bearing on the subject were set forth, together with the results of observations made during ventilation tests carried out at the mining department of the Zinc Corporation.During the subsequent discussion the question was raised of the possibility of any practical application of the method of attack described, and also whether the theoretical considerations mentioned were likely to be of any real utility to the mining engineer engaged in ventilation work in a metalliferous mine.

Jan 1, 1923

By B. McCosker

The choice of the appropriate delivery process for a project is often not adequately thought about. The industry needs to be prepared to break its preconceived mind-sets on delivery procedures. Industry should also be prepared, on a project by project basis, to commit to a critical review as to how the assessment and then selection of the best procurement method can best optimize the project outcome for both client and contractor. Conventional standards and biased reliances and experienced based preferences should be challenged. To achieve this requires a paradigm shift in attitude to both the process of tendering and the evaluation of tenders. Tender and contracting practices are dynamic and have moved away from solely cost based assessments. Tendering contracts arise imposing changed duties upon owners. Traditional contract delivery models have shifted, reflected in part by the trend towards relationship contracting. The categories of contract options are not closed. Many are but hybrids of other time-tested models. This paper considers options available for any brownfield or greenfield project. The principles outlined are translatable to supply, upgrade, operation and maintenance arrangements.

Jan 1, 2002

By J. W. Thompson

This work is a codification and annotation of the Congressional enactments relating to minerals, mineral lands, and mining. It covers every enactment of Congress from the original ordinance of 1785 to the present time, as well as all sections of the Revised Statutes of the United States relating to these subjects. These laws are grouped according to their general subject matter, and are arranged thereunder in numerical or chronological order. Many of the mining statutes include matter not pertinent to the subject, and only those parts of such acts are quoted as will properly show their relation to minerals and mineral lands and indicate how they should be construed. Some mining acts have been repealed or have become obsolete, and others have become incorporated substantially in sections of the Re- vised Statutes; but these are retained in order to show the changes made, and the constructions placed thereon by the courts are given as aids in construing the new or repealing acts. The annotations consist of legal propositions abstracted from the decisions of the various courts and executive officers of the Govern- ment that have interpreted the sections and statutes so codified. These legal propositions are arranged under the different sections and acts with appropriate headings, titles, and subtitles, in logical order, exhibiting the present status of each particular section or act and its application to the subject of mines and mineral lands. The annotations do not purport to be abstracts of decisions on the sub- stantive law of mines and mining generally, but are limited strictly to the interpretation placed on a given section or act definitely re- ferred to by a court or executive officer by the number of the section of the Revised Statutes or the volume and page of the Statutes at Large in which the Congressional enactment is found. It may be observed that the legal propositions stated are not always pertinent to the particular section or act under which they are classed and of which they purport to give a construction. The arrangement, however, is not an arbitrary one, but is so made for the reason that the courts or officers in the construction of a particular section or act definitely referred to by number or volume and page incorporated in the decision matter not strictly pertinent to the par- ticular section or act so designated. This statement applies especially to the interpretations placed on the sections of the Revised Statutes. The decisions abstracted for the purpose of this work are those of the United States Supreme Court, 234 volumes; the various Federal courts, 214 volumes; the decisions of the Department of the Interior

Jan 1, 1915

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By C. D. Messelt

The Bureau of Mines investigated the application of a diffusion model to sintering rate data developed for lithium titanium ferrite. The data were obtained by sintering pressed pellets under identical conditions for various times up to 11 hours. Stereological measurements were made on polished sections, and sintering rates were calculated. A model for intermediate stage sintering was fitted to the stereological data. This procedure produced a method by which these type data could be used to study the relative importance of volume and grain-boundary diffusion under a variety of sintering conditions.

Jan 1, 1979

By I. A. Kunasz

This paper is not intended to review and re-state general information on lithium, but rather to analyze the paradigm that has caused such a rapid rise in lithium production and the development of new lithium producing centers. Details on pegmatites, brines, concentrate and chemicals are amply covered in a number of publications ? SME?s Industrial Minerals and Rocks, Industrial Minerals, Roskill and a host of other publications. There is no question that the latest interest in lithium has been driven by the potential development of the electric car. This stimulus prompts one to recall two symposia: 1. ?Lithium Resources and Requirements be the year 2000?, organized in 1976 by the U.S.G.S. in Denver (1) and the sequel 2. ?Lithium ? Needs and Resources? at Corning, N.Y. (2).

Jan 1, 2011

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

By Walford S. Wright, NORMAN EBBLEY

During the past decade (1937 to 1947), including the war years of heavy demand for metals, the United States realized about one-eighth of its antimony requirements from domestic production, chiefly in Alaska. In World War II, our foreign supply sources became endangered; and uncertainty in our Far Eastern supply made this nation focus on Alaska’s mineral resources with a Production Gear that centered in the Bureau of Mines experimental station at College (Alaska). The development work known as District or central deposits. The strategic mining districts included that of central Alaska was reorganized at Ketchikan Mining Districts. Mines were located here had produced considerable quantities since 1901; but methods for exploration had come from 1936 to spring 1942, some $4 million produced in gold alone. Statistics relating to available ores are those selected by type and exploitation periods with wide variety applied. During the summer of 1941, as part of an extensive Geological Survey program continuing through funds provided by U.S., geological surveys spent six weeks mapping an area approximately two square miles surrounding mines. The mines working both surface & underground work employed these men in mapping exercises.

Jan 1, 1948

By J. du Plooy

Mintek has implemented a training scheme that provides students with the experiential training requirement for the National Diplomas in Chemical Engineering and Extraction Metallurgy. This note describes the main features of the scheme and the course content, and our view of future developments in this area.

Jan 1, 1998

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By G. A. Vissac

METHODS of coal preparation have been greatly developed and improved during the past few years. Under the pressing competition from substitutes that have been displacing coal as a source of heat or power, the coal industry has been able, in many cases, not only to hold its own but to regain much of the lost ground, by offering better products of a higher value. The purpose of this paper is to present, in a brief and simple form, the principles of the latest methods and machinery used in coal preparation, in order to enable the coal operator t0 select methods and equipment capable of solving his own problems in the most efficient and economical way. The paper will deal, in the main, .with coal cleaning. It must be emphasized, however, that a complete coal preparation study covers many other operations, such as handling, screening, de-dusting, dust-proofing, and ash-conditioning. Handling Coal From the producing face to the railway car, coal must be handled with great care, t0 prevent degradation, because the coarser sizes are not only easier to clean than fines but, for our markets, they are often the more valuable. Generally speaking, such care is less important or is unnecessary in the Old Country, where conditions are different. The best way to minimize breakage is to avoid gravity methods in coal transportation. All chutes in a preparation plant should be shaken mechanically, and cleaning processes requiring large surge bins must be avoided. De-Dusting De-dusting of coal is accomplished by the use of vibrating screens, fans, or classifiers, or by a combination of these. Fines below 1/32-in. (or coarser than this, with some coals) can very seldom be cleaned efficiently. Common practice is to discard them immediately, if the moisture content of the coal allows this to be done. Otherwise, they are liable to give unnecessary trouble, either in the form of dust or sludge, which are difficult to collect or to settle. Flotation is the only process which will effectively clean fines.

Jan 1, 1937

By R. J. Gunderman

Explosionproof electrical enclosures for coal mine face equipment have been of the same basic design for many years without significant change. Characteristics for potential improvement were investigated through interviews, visits to mines and studies. Improved safety, health and productivity were the goals. Areas identified for improvement included rapid venting of pressure build-up due to an internal explosion, quick and easy entry or removal of cable entrances, and a quick and easy cover removal for rapid component access. Concepts were identified and evaluated, and the more promising devices were fabricated and tested. Encouraging results from initial tests led to further design refinement and establishment of design guidelines. These design guidelines for a pressure vent and for an elastomeric grommet type cable entry are described along with the testing used. An application for an experimental permit was requested from MSHA. After test and evaluation experimental permit #396 for evaluation in an underground coal mine was granted.

Jan 1, 1980

By H Thanasekaran, J Kohmuench, B Seaman

To achieve an efficient separation in the flotation process, valuable particles need to be selectively segregated from the gangue while utilising a minimum number of flotation stages. TodayÆs existing flotation technologies are effective for fine particle size classes; however, limitations due to particle buoyancy and bubble-particle detachment restrict the effectiveness of traditional flotation approaches on coarser particles. As a result, flotation circuits are generally configured to process only fine particle size classes in order to maximise recovery in the primary stages. Eriez has invented a novel flotation technology, the HydroFloat, which overcomes these limitations by carrying-out flotation in a dense, fluidised-bed medium allowing for the recovery of coarse particles (>0.250 mm). Over the last 15 years, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3 mm diameter in primary flotation circuits. This paper includes discussions on the history of this technology, process theory, existing applications, and a review of recent sulphide-based laboratory test work conducted for Newcrest mining and others. Benefits of this approach, such as improved recovery, low energy consumption and reduced reagent addition will also be reviewed.CITATION:Kohmuench, J, Thanasekaran, H and Seaman, B, 2013. Advances in coarse particle flotation - Copper and gold, in Proceedings MetPlant 2013 , pp 378-386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By Claude Deveau

"With ever decreasing feed grades, finer mineralogy and increased demand for product, it became obvious that a major step in equipment performance was required to reduce operating costs and increase production. Offsite testwork indicated that a Centrifugal separator was capable of recovering fine tantalum and that the newly developed C Series Falcon concentrator would be capable of replacing many pieces of aging equipment and provide improved performance. Further investigation led to the rental and the purchase of a Falcon C20 concentrator followed by a C10 to maximize circuit performance.Falcon Concentrators Inc’ s practice of working with the customer mirrors Tantalum Mining Corporation of Canada’s (Tanco) philosophy of continuous product development. This synergy honed valve design for continuous operation in a highly abrasive ore environment.Tanco has recently purchased two more Falcon concentrators for the recovery of additional tantalum from its spodumene circuit. These new units have additional user friendly operating features partially based on developments made at Tanco.The Falcon C Series units have enabled Tanco to maximize recovery of tantalum that was otherwise lost while using the original conventional gravity circuit."

Jan 1, 2000

Owing to improvements in computer capacity, it is now possible to undertake fully coupled or partially coupled, three-dimensional (3D) hydromechanical Finite Element (FE) simulation of mines, including explicit representations of large numbers of discontinuities. The analysis requires fewer assumptions than uncoupled analysis or two-dimensional (2D) analysis, but may require a change in how hydrological data is collected. The way hydrological data is incorporated in stability assessment and the approach to uncertainty in hydrological information also requires discussion. The current procedures for this type of analysis are discussed, along with some practical difficulties and teachings from early applications. A work flow for integration of 3D hydromechanical modelling with pit planning and some considerations for the management of uncertain data are also proposed.

May 1, 2010