Search Documents

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By J. Shanks

A S far back as 1925, Brazeau Collieries, Limited, became interested in .briquetting. This was brought about by complaints from their principal customer that stack losses, due to a high percentage of fine coal in their mine run, were excessive. The Company considered oil spraying of the fines. This, after some experiments and tests had been made, was ruled out as uneconomical and impracticable. When sufficient oil to be effective was put into the fines, it caused the coal in the tender of stoker-fired engines t0 arch over the screw feeder. The Company ultimately placed their problem in the hands of the Re-search Department of the University of Alberta. Experimental work was carried on by this department over a period of more than a year. The results obtained and the experience gained in this research work were conveyed to Brazeau Collieries in a report dated October 31st, 1929, and in a supplementary report dated February 2nd, 1935. Most of the results obtained in experimenting with Brazeau coal are embodied in a brochure, reprinted from the proceedings of the Second International Conference on Bituminous Coal, Vol. 19-24-28, entitled Principles in the Briquetting of Coking and Non-Coking Bituminous Coals, by E. Stansfield and W. A. Lang. All who are interested in briquetting should read this brochure. In the writer's opinion, iris the most important treatise on the subject printed in recent years. The results given in the paper are, of course, those obtained in laboratory investigation. It was pointed out to the writer that it would be most interesting to have such results correlated with those obtained in commercial practice. In this short paper, an attempt is made to do so.

Jan 1, 1942

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

By Worner H. K

Education has always been a topic to rouse the interest of mining and metallurgical engineers, but the recent activities of the Education Committee of the Australasian Institute of Mining and Metallurgy 1, 2, together with the moves throughout the Commonwealth to extend the field of technological education, have made the subject a very live one at the present time. The authors have felt it would be appropriate that on the occasion of the First Ordinary Meeting for 1950, in Victoria, some contribution should be forthcoming concerning the history, present status and possible future trends of mining and metallurgical education in this State. As for the past, the time approaches when there will be none having personal recollections of the beginning of Victorian mining schools or of the men who started them. As for the future, it is obvious that rapidly expanding metal-producing and metalconsuming industries will demand a greater output of competent graduates and diplomates. The era immediately ahead seems to be bristling with opportunities, but mining educators need to temper their enthusiasm for various policies and programmes with the realisation that they are helping to train men who will be leaders 15-20 years hence when the problems of industry and trials of life generally may be very different from what they are to-day.

Jan 1, 1950

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, whereas in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600?1000°C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed. For over 60 years, Outotec has progressively been developing the principle of fluidized bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidized bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

This publication summarizes the in-house and contract research and development projects programed for fiscal year 1981 by the Bureau of Mines under its Minerals Environmental Technology activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau?s environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. The environmental research and demonstration activities of the Bureau were consolidate in 1979 with the formation of the Minerals Environmental Technology program, which is directed toward the elimination or reduction of environmental problems associated with the extraction and processing of minerals. Among the efforts underway are development of data and technology for assessing the potential environmental impact of minerals development, for monitoring minerals extraction operations, and for establishing viable reclamation requirements on abandoned mine lands; development and demonstration of technology 'or control of environmental disturbances during minerals extraction operations; development and demonstration of land reclamation and mine closure techniques to restore or enhance the productive use of mined lands; development of engineering techniques that incorporate state-of-the-art mining environmental technology in the design and planning of minerals extraction operations; development and demonstration of new mining systems that greatly reduce or eliminate the adverse environmental impacts of minerals extraction; and providing the technologic base for Federal, State, and local establishment of environmental standards for mining operations. Included in the minerals-processing-related work are projects to clean mineral-processing waters: demonstrate a Bureau process for scrubbing SO from powerplant stack :;as; recover dissolved minerals from process streams; stabilize discarded dusts, slags, and tailings: remove hazardous contaminates from byproduct wastes; reduce generation of waste solids; and improve metallurgical process engineering to eliminate pollution. Approximately $21 million was appropriated for this work in fiscal year 1981.

Jan 1, 1981

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

By Lisa M. Splitter

Drilled displacement piles were constructed as the foundation for a proposed 10-story building in San Francisco, California. At the study location, the stratigraphy consists of 14 to 21 feet of fill and 13 to 23 feet of weak, compressible clay (?Bay Mud?), underlain by dense sand, stiff clay, and bedrock. A sensitive critical public utility is located within approximately 20 feet of the constructed piles along one side of the building. The utility pipeline is entirely within the Bay Mud where it is adjacent to the project site. The San Francisco Public Utilities Commission (SFPUC) developed limits on the allowable total and differential movement of the utility pipeline. As requested by the SFPUC, inclinometers and piezometers were installed to monitor the soil movement and pore pressure increases in the Bay Mud caused by the installation of drilled displacement piles. Action levels were set such that if displacement and/or pore pressures reached an action level, the installation methodology would be reevaluated and additional measures to reduce these effects would be implemented. This paper will present the sequence of pile installation near the pipeline and monitoring points, and the data collected from inclinometers and piezometers at variable depths and distances from the piles. The data will highlight the build-up and dissipation of pore pressures over time and the displacement of Bay Mud caused by the pile installation. The conclusions of the study are useful in determining sequencing, spacing, predrilling, and other measures that can be implemented to decrease the displacement potential and pore pressure build-up in soft clays.

Jan 1, 2009

By Stephen M. Smading

The Jinping-II hydroelectric project in China features four parallel headrace tunnels approximately 18-km- (11-mile-) long. Two will be excavated by tunnel boring machines (TBM) and two by drill-and-blast. A nearby fifth tunnel is being excavated by a 7.2-m (23.6-ft) TBM to draw down ground water in advance of excavating the headrace tunnels. Unique onsite assembly of a 12.43-m (40.7-ft) main beam TBM and backup system was completed on Sept. 18, 2008 in the remote mountains of the Sichuan province. The equipment was assembled onsite, without previously having been assembled and tested in a factory, using a method called onsite first time assembly (OFTA). This paper addresses the following topics: ? Project description including geology and terrain. ? The decision process leading to onsite, first time assembly, the assembly process and logistics, and lessons learned. ? Design features of the TBM and backup system. ? Operational history from startup to the writing of this article.

Jan 1, 2009

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption if this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 mill ion tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably are in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By G. O. Rading, B. O. Odera, M. J. Papo, R. Couperthwaite

"Platinum-based alloys are being developed with microstructures similar to nickel-based superalloys for potential high-temperature applications in aggressive environments. Since the chemistries of nickel and platinum are similar, Pt-based alloys can be made with gamma prime ~Pt3Al precipitates in a gamma (Pt) matrix. Currently, the Pt-Al-Cr-Ru system is one of the bases for developing Pt-based alloys, where Al allows the formation of thePt3Al precipitate and also gives protection from the alumina scale formed, Cr provides oxidation resistance and stabilization for the L12~Pt3Al phase, and Ru provides solid solution strengthening in the (Pt) matrix. Four Pt-Al-Cr-Ru-V and two Pt-Al-Cr-Ru-V-Nb alloys were made, with compositions based on a quaternary alloy, ~Pt82:Al12:Cr4:Ru2, which hadpreviously been identified as having optimum properties. Four of the as-cast alloys had the targeted two-phase structure of ~Pt3Al and (Pt), and two were single-phase ~Pt3Al. Vanadium partitioned more to (Pt) than to~Pt3Al. There was an improvement in hardness compared to the quaternary alloys. The best addition of V was ~15 at.%; higher additions resulted in brittle intermetallic phases of the Pt-V system. The effect of Nbcould not be ascertained because of its high losses."

Jan 1, 2015

Some 50 miles of tunnel have been driven in the Snowy Mountains Area since tunnelling commenced in 1951. Hates have improved progressively due to the know-how of American supervision and use of large matched equipment of modern design.The work has been carried out by contractors, working almost exclusively under schedule of rates contracts. The Authority has maintained active research into tunnelling problems, especially that of support, and this has resulted in considerable economies and improved rates of progress. The contractors also have sought economies both by management and equipment techniques. Ammonium nitrate came into favour as an explosive essentially because of its lower cost, and handling techniques have improved progressively. Rock conditions preclude use of the "Mole" type equipment in its present stage of development, but one contractor introduced the "sliding floor" and this could exert a great influence on future tunnelling methods.Examination of tunnels that have been in service for some time confirmed the quality of the work and endorsed the policy of continued research and development.GENEHALThe Snowy Mountains Scheme provides for the diversion of the Snowy and Eucumbene waters through two transmountain tunnels to the western river systems. These diversions, together with additional regulations provided for waters already flowing inland, will provide an average additional discharge of 1,818,000 ac it per year for irrigation.Furthermore, approximately 6,000 million kWh of electrical energy will be generated annually in power stations with a total installed capacity of some 3,000,000 kW (Fig. 1.).INVESTIGATIONThe aim of investigation work is firstly to collect sufficient information to allow the overall scheme to be planned and then to follow up with detailed information on eachproject. The correct balance for all aspects of this work is a matter for keen judgment, as the tunnels must be planned...

Jan 1, 1963

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007