Search Documents

By M. J. Slater

Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. Continuous fluidized-bed ion exchange is an advantageous technique for processing dirty effluents and thin slurries. It also reduces resin inventory and equipment cost compared to fixed packed beds. A simple continuous fluidized-bed unit has been investigated for treating effluents and its performance is described. Breakthrough curves were first obtained from static fluidized fixed beds; these data were then used to determine the required operating conditions for a periodic-flow, countercurrent fluidized-bed ion exchange system. A waste stream, containing about 56 ppm copper, was treated in the continuous system using an extraction fluidized bed depth of 203 cm and a flow rate of 1.22 cm3/ cm2s (900 gph / sq.ft) to yield an effluent containing less than 0.02 ppm copper. A generalized design method is proposed for similar chemical systems.

Jan 1, 1978

A consideration of mining ventures and the changes of an environmental nature that occur. The paper is introduced with a general statement claiming recognition that mining ventures are important to human well-being but that these need to be justified against the environmental changes that they bring about. The various factors that need to be considered are cited followed by an historical review of mining activities. The various environmental issues are discussed under three headings; socio-economic, physical and biological, prior to reviewing the world's demand for minerals including fossil fuels. In conclusion guidelines for appraising mining ventures relative to environmental changes that may occur, are given.

Jan 1, 1981

By J. Kim, H. Cho

The objective of the experiment was to investigate the efficiency of hindered-settling column in recovering carbon from anthracite. Two types of Korean anthracites were prepared for feed materials. Each sample was crushed and classified by size, and washability analyses were performed. Separation efficiency was evaluated under various operating conditions using a laboratory scale hindered settling column. Results showed that the carbon recovery was higher for the smaller sizes, but the purity of the product was better for the larger sizes. In, overall, 2-0.21mm particles of 40-45 % ash could be processed into about 20 % ash products.

Jan 1, 2002

By George C. Branner

This circular is concerned with eight nonferrous scrap metals as they generated, collected, prepared, and consumed in California. Brief reference also is included with respect to Nevada and Hawaii. Four of these scrap metals - copper, lead, aluminum, and zinc - are of major importance and make up about 95 percent of the total value, whereas the remaining four - antimony, magnesium, nickel, and tin - make up the remaining 5 percent. For convenience, the subject matter is divided into three parts, (1) Data with respect to the collection, preparation, and marketing practices that are common activities to all the nonferrous scrap metals; (2) separate discussions and statistical data with respect to each of the eight nonferrous scrap metals in California; and (3) data with respect to Nevada and Hawaii.

Jan 1, 1962

By H. Walqui

The Empire concentrator was built in four stages, with the latest stage accounting for 50% of the overall plant capacity. Over the past 5 years, the average throughput of the three grinding lines has decreased by 50 LTPH (15%) without significant changes in ore characteristics and despite the addition of secondary grinding capacity to supplement the existing pebble mills that are the constraint of the grinding circuit. This paper discusses the different areas under study that are aimed at optimizing grinding circuit utilization which includes improving system logic, pebble crushing operation and pebble mills operation.

Jan 1, 2009

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By Brian Fulcher

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft 3/sec) of water into Southern California. The 13 km (8-mile) tunnelling project is well underway and consists of two, 5.8 m (19-ft) diameter TBM bores through extremely variable geological conditions. An extensive and essential pre-excavation drilling and grouting program was performed in all reaches of the Arrowhead Tunnels Project, located north of San Bernardino, CA. This program supported the advance of two hybrid hard rock TBMs though extremely challenging ground conditions under substantial ground cover and up to 27 bar (900 ft) of ground water pressure. The well known San Andreas Fault lies nearby and has greatly influenced the local geological conditions. This paper will describe the means, methods and materials used throughout the numerous phases of the pre-excavation grouting program. It will also describe many versatile, flexible and innovative drilling and grouting methods and equipment systems utilized to improve performance, save time and costs in constantly changing geological conditions. Considerable lessons learned have been learned while overcoming some extremely formidable ground conditions and safely advancing the tunnels.

Jan 1, 2008

By M Rattenbur, A B. Christie, S C. Cox

A new minerals initiative to increase the level of understanding of New Zealand's mineral resources and to promote the development of minerals began earlier in the year in a partnership pilot-project between Crown Minerals and the Institute for Geological and Nuclear Sciences (GNS). The project aims to gather a set of comprehensive geoscientific data and build a series of digital GIS packages to highlight New Zealand's mineral prospectivity. The pilot study was carried out at a regional scale, and is focussed on mesothermal gold mineralisation in the South Island. A significant amount of geological data and information was sourced from open file technical reports held by Crown Minerals and from various databases held by GNS and has now been compiled into a single GIS dataset, which will soon be made freely available to interested parties. In addition to this comprehensive data compilation, prospectivity modelling using Weights of Evidence techniques was undertaken to highlight those areas likely to contain ore deposits. It is clear from this study that the South Island of New Zealand remains highly prospective for mesothermal gold mineralisation. Many of the highly prospective areas, which also contain historic mine workings, remain open for exploration. The study not only highlights these areas, but also other areas where the potential for similar mineralisation exists, in all likelihood with no surface expression. The study has also highlighted the value of many of the open-file technical reports held by Crown Minerals and the need to carry out additional studies using this and other available data at a more detailed level, possibly as the basis for a web-based minerals information system.

Jan 1, 2002

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

In Southern Africa, historic mining and mineral processing of base metal deposits have almost exclusively focussed on the extraction of major metals, leading to the loss of remaining valuable raw materials into tailings dumps and waste rock piles. At the Namib Pb–Zn mine (Erongo Region, Namibia), historic base metal tailings deposits are present as unreclaimed exposed waste piles. The tailings comprise silt- (fraction A: d50 = 25 to 48 μm) to sand-sized (fraction B: d50 = 86 to 185 μm; fraction C: d50 = 210 to 230 μm) material and contain major concentrations of base metals (Pb av. 1.15 mass%, Zn av. 3.20 mass%), S (av. 9.95 mass%), as well as lower values of other metals (Cu av. 490 μg/g, Cd av. 133 μg/g, Ag av. 22 μg/g), and critical elements like Sb (av. 14.7 μg/g) and In (14.3 μg/g). Former mineral processing only targeted the extraction of galena and sphalerite. As a consequence, qualitative mineralogical composition of the tailings is similar to that of the primary ore. Ca–Fe–Mg(–Mn) carbonates, quartz, micas, chlorite, minor graphite, magnetite, and rare parisite relate to the former host rock and gangue matrix, whereas Fe-rich sphalerite, galena, magnetite, pyrite with minor pyrrhotite, rare arsenopyrite, marcasite, cassiterite, and accessory scheelite are original constituents of the primary ore. Reprocessing of such a material would be challenging, but a mixed Pb–Zn concentrate enriched in Cd and Ag might be obtained. In future, possible reprocessing of Namib tailings and associated disposal of wastes into an appropriately designed repository would not only generate valuable metal commodities, but such activities would also eliminate a major metal pollution source from the local environment.

Sep 9, 2024

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Richard F. Hewlett

Engineers at the Bureau of Mines Denver Mining Research Center have been a research program investigating the theory and application of mine sampling. Part of this program is an investigation of the efficiency of sampling methods that involves development of sampling-method theory through simulating ore-deposit samples and assays, using - electronic digital computer. Theoretical developments are checked against actual ore-deposit sampling, assay, and production data by the commonly used polygonal and triangular methods of computing grade and tonnage of ore reserves. To speed the computing procedures, a program has been developed utilizing a medium-size digital computer for computing ore reserves by the polygonal method. This program calculates nine prismoids per minute at a total cost of $0.21 per prismoid. The complete program, written for an augmented IBM 650 computer, is described in detail; it can be used without change for computing ore reserves for a low-grade deposit. Modifications necessary to convert the program to compute ore reserves for virtually any other type of deposit or grouping of ore horizons also are given; however, the program is limited to using only vertical drill-hole data.

Jan 1, 1962

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By José Cuadros

"El presente trabajo describe la aplicación del ""método gráfico de estabilidad"" como herramienta de diseño en el dimensionamiento de tajeos a través de técnicas geomecánicas que pueden ser aplicadas en otros yacimientos con similares condiciones que la mina Chupa a fin de mejorar la productividad y y mantener adecuadas condiciones de estabilidad de las excavaciones. En consecuencia, el dimensionamiento de los tajeos de Chupa fue uno de los varios trabajos que la Empresa Minera Iscaycruz S.A. realizó para el inicio de la explotación de este yacimiento a través del método de minado “tajeos por subniveles” con la utilización de taladros largos, sostenimiento con cables y relleno cementado. "

Sep 13, 2001