Search Documents

By James E. Lawver

Part I describes the general geology of the Florida deposits. As the lucrative Bone Valley Formation is depleted, replacement production will move progressively into areas of total Hawthorn production. The reserves of the immediate future are a mixture of two distinct ore types referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation that has been Florida's source of production for the past 100 years and will respond favorably to present beneficiation practices. By contrast, the lower zone ore contains significant quantities of dolomite that must be removed in order to produce an acceptable grade pebble or flotation sized product. Part II reviews past practice and describes future trends in mining and ore transportation. This presentation (Part III) is confined to the problems of beneficiation, waste disposal, and environmental regulation.

Jan 1, 1983

By J. P. Josien, Didier C.

ABSTRACT: France now faces the closure of most of its mining sites. Surface instability risk may sometimes remain, especially where large underground voids exist. This paper illustrates the importance of failure mechanisms identification in order to define properly how to manage the residual risk. RESUME: La France fait aujourd’hui face à la fermeture de ses exploitations minières. Des risques d’instabilités de surface peuvent persister, notamment lorsque des vides résiduels existent au sein des travaux souterrains. L’article illustre l’importance que présente la nature des mécanismes de rupture potentiels dans le choix des mesures compensatoires à adopter pour gérer le risque résiduel à long terme. ZUSAMMENFASSUNG: In Frankreich stellt sich derzeit das Problem der definitiven Schliessung des meisten Bergwerke. In manchen fällen ist die Stabilität der Oberfläche nicht garantiert, speziell wenn unter Tage nicht verfüllte Hohlräume verblieben sind. Dieser Bericht zeigt die Wichtigkeit, bei der Auswahl geeigneter Langzeit-Risikomanagementmethoden, der verschiedenen Mechanismen mit denen ein eventueller Bruch an die Tagesoberfläche geraten kann.

Jan 1, 2003

By T. F. J. Hälbich

Namakwa Sands aims to conserve environmental resources and prevent or minimize environmental impacts from its operations. The challenge faced by Namakwa Sands is the rehabilitation of the arid winter rainfall Strandveld and lowland Succulent Karoo vegetation zones affected by its mining activities. Extensive experimentation with different rehabilitation methods resulted in the development of an effective rehabilitation programme. The use of topsoil as a seed bank and shade-cloth as windbreaks have significantly aided the rehabilitation process. The aim of the programme is to stabilize the soil environment so as to allow the germination and development of the local plant species. The ability to control wind erosion is critical to the success of the rehabilitation effort. A programme of biodiversity audits has been started to measure the recovery of plant species in the rehabilitated area. The principle of continuous improvement, coupled to site-specific rehabilitation studies, is applied to enhance the rehabilitation programme.

Jan 1, 2003

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

This paper considers the application of recent laboratory gas sorption data to the understanding outburst phenomena in underground coal mining. Previous use of threshold limits based on gas content and coal rank are placed in perspective. Although this work focuses on overseas research and experience, parallels can be drawn for New Zealand coal settings, taking into account localised mining and geological factors.

Jan 1, 1994

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projets programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By Sanjeev Malhotra

The American Petroleum Institute (API) method of predicting pile capacities in sands is reviewed. Factors that influence pile capacity such as soil parameters, pile parameters, loading effects and installation effects are listed. In addition, the simultaneous occurrence of physical phenomena such as grain crushing, pile shaking, stress-redistribution and plugging add to the uncertainty in the prediction model. To better understand the method of prediction, each parameter and the associated uncertainty is revisited. It is evident that these factors are inter­related and sometimes compensating. This discussion also draws attention to the influence that pile installation procedures can have on pile capacities and highlights the need for field experience with various pile installation procedures for designers. In summary, the strength of the method lies in its simplicity and ease of application, but the possible savings generated by an improved method are too substantial to ignore.

Jan 1, 2000

By Fredrick L. Johnson

The Bureau of Mines, under Congressional mandate, conducted a mineral survey on the Park Range WSA (Wilderness Study Area) in 1984 and 1985. The WSA, located about midway between Tonopah and Ely, encompasses 47,268 acres. No mineral resources were delineated, nor were workings found, during the investigation. There has been, however, exploration in and near the north end of the study area. ASARCO is actively exploring a block of 41 claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block is almost entirely in the study area. The Morey mining district, 7 miles southwest of the study area, produced silver and lesser amounts of gold and lead sporadically from the mid-1860's through the mid-1960's. The WSA is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. The Paleozoic rocks have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. Additional exploration in the north part of the Park Range WSA may lead to delineation of gold resources.

Jan 1, 1986

[nder ' 1Oclific?atic>n 1 l', of Cant r Ict No. S012?U7 , the T1. S. l urc ,:i.11 of Miries ontracted tivit.l '1 -l:eudurn? Barry t1rirl ,~:>:'nci.11c:, for the 1>crfcocrnancu of a afet, Analynin Q::tc n Study to develop a plan for thc organiration nrld opera¬ion of a 'Lur('an ,`,afutj i ily ;i Cn11tur, r Before the con)y)lctic>n of the stucly, the Abiretu.l ustaldish d such a center, the WniL1, and Safety i?'\naly:-.in Cnmtor (l1S;'J:), under the dirucHan of fly, Assistant Director of JTc'"?ltl) 11111 .itut~ 1O1- 'l (.. -11: 'C'a) :_'-, ?'( )'t. 11. ~.C is 11 c' iC1cnlC:rtc:rr'd at the 1)crnv(jr Federal Center, 1)u:r',L C,r_i1f,U, rK.]

Jan 1, 1972

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.

By N. Andersen

During the preliminary design phases and feasibility study of a proposed vertical shaft, a vertical diamond drill-hole is normally drilled on the site. This paper outlines how rock mass characteristics, in-situ rock stress, rock strength, hydrological characteristics, and structural parameters can be determined using wireline logging of this borehole. In addition, a rock mass classification scheme is developed, based on published work, and in particular the Q-factor is adapted to assess the stability of raise-bored shafts. The ‘stick plot’ is introduced, which combines all geotechnical parameters applicable to the stability of a vertical shaft into a colourcoded format where cross-correlations can readily be made on a day-today basis during the shaft-sinking process.

Jan 1, 2015

By Vance G. Leak

Leaching of manganese from low-grade Minnesota ores was studied over the temperature range 25° to 225° C at atmospheric and elevated pressures to demonstrate that good recoveries of manganese could be achieved from unroasted ores using reagents available nearby. Various combinations of ore, pyrite, lignite derivatives, and sulfuric acid were tested on a small scale. Pyrite alone required the highest temperature to effect a good extraction, but the combination of pyrite, lignite char, and sulfuric acid solubilized 99 percent of the manganese after 30 minutes of reaction at 75° C.

Jan 1, 1971

By Gordon Revey

Over ten million pounds of explosives are used daily to blast rock in mines, quarries and construction projects throughout the United States. Despite the immense volume of explosives used, serious incidents involving the legal use of explosive materials are rare. Unfortunately, when incidents arise they are well publicized, whereas the great majority of blasting projects-even the most challenging ones—quietly occur without incident or public recognition. Although unfair, media coverage focuses on incidents and/or accidents, and as a result skews the public’s perceptions of our industry. These negative perceptions about blasting profoundly effect our work. Most apparent are the community groups who organize to fight blasting work. However, other impacts are more insidious and have long-term effects on our industry. For instance, planning engineers or government agencies often prohibit blasting to avoid the public’s adverse reaction or because of general fear of blasting impacts. Ironically, as regulations and specifications continue to curtail our industry, the net effect is an increase in the cost of rock excavation. As taxpayers, we suffer needlessly by paying more for government funded construction projects. As blasting professionals we are additionally penalized through loss of work.

Jan 1, 2001

"The U.S. Bureau of Mines established on August 15, 1983, The Generic Mineral Technology Center for Respirable Dust (Dust Center) within the Mining and Mineral Resource Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University, and in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. In 1986, Michigan Technological University (MTU) was awarded a grant through the Dust Center. The center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health law, which is ""... (to) permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis of any other occupation-related diseases..."" The Dust Center's program is designed to foster an accelerated attack through fundamental research on problems confronting the control of respirable dust in mines. The interactions of the universities and the research program components in the characterization of coal seams, respirable dust particles and the workers lungs are depicted in the logo of the Dust Center.The primary goal of the Dust Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The Dust Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection of dust in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) the relationship of the mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines, and to other dusts such as those generated by diesel equipment. Achieving the Dust Center's goals also involves the training of engineers and scientists, graduate students, and undergraduate students through their respective institutions, and technology transfer to industry. The distribution of personnel in the various universities are presented in Table 1. A directory of Dust Center principal investigators is presented in Appendix 1. A summary of degrees granted and mineral sector employment is presented in Table 2. The subjects of theses developed under the various research projects are presented separately in Volume 7. The center research is fully compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities (see Volume 2). Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease studies are available as a result of the existing relationship between NIOSH and West Virginia University. Figure 1, Respirable Dust Center Projects and Activities, presents the various projects in the five major areas of investigation and the scope of characterized dust samples, the suite of tests, the sampling and dust generation methods, and the size, chemical and mineralogical analysis performed in the center. Table 3 presents a summary distribution of the 95 publications and presentations that have emanated from the center. In addition there are more than thirty presentations made at each annual Dust Center review meeting. The titles, authors and location of presentation for publications supported by the Dust Center are presented in separate publication volumes for 1984 (Volume 3), 1985 (Volume 4), 1986 (Volume 5) and 1987 (Volume 6)."

Jan 1, 1988

By R G. Barker, A B. Christie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. More than 11 Moz of Au and 50 Moz of Ag have been produced from epithermal deposits in New Zealand, almost entirely from 50 deposits in the Hauraki goldfield. Since the 1980s, new deposits have been discovered at Waihi (Favona, Trio, Correnso) and nearby at Golden Cross. Feasibility studies into reopening the Talisman mine at Karangahake are continuing, and advanced projects with preliminary inferred resource estimates are reported at Wharekirauponga, Neavesville and Muirs. In the Taupo Volcanic Zone, 11 prospects have been drilled, resulting in the definition of large but low-grade Au-Ag resources at Ohakuri. In Northland, several Au, Ag and/or Hg prospects are known, and small quantities of Ag and Hg have been mined. Six prospects have had some drilling, with the most advanced exploration at Puhipuhi. The application of Taupo Volcanic Zone geothermal systems research to the modelling of former hydrothermal mineralising processes in some epithermal prospects has enabled better targeting of exploration.CITATION:Christie, A B and Barker, R G, 2015. Exploration for epithermal gold deposits in New Zealand, in Proceedings PACRIM 2015 Congress, pp 533–540 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A. C. Fieldner

The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials5 that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-ran]: coals according; to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.

Jan 1, 1935

By F. X. Spachtholz

"Raw materials industry is crucial for national economy. German mining companies are known for their high degree of resource efficiency based on modern technology and know how. K+S is one of the world’s leading suppliers of standard and specialty fertilizers. In the salt business, K+S, with sites in Europe as well as North and South America, is the world’s leading producer. The mine sites of K+S are distributed all over the world producing mainly potash and magnesium salts and rock salt. Focus is on the sustainable use of the natural deposits in order to stay competitive. For this reason a raw material policy, both national and international, is necessary to ensure access to new mineable deposits which are still available in Germany. Further on, knowing market conditions is a must for sustainable development. At least sustainability and resource efficiency in potash and rock salt mining are achieved by constantly developing new technologies as well as optimizing the organization and improving qualification of workers."

Jan 1, 2011

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956