Search Documents

By Hans M. Ewoldsen

The generation and evaluation of solutions to body force problems is of extreme interest to the geotechnical profession, as all natural stress states must necessarily include some contribution from the weight of the material. In this chapter the elastic solution for the stress field around a circular, horizontal tunnel at an arbitrary depth beneath the surface of a half-space is reexamined. The influences of body force, initial stress, and free surface proximity are examined and related to in-situ cases. The solution as presented deals only with an isotropically elastic medium; this medium is further considered only in a half-space configuration. It is readily apparent that these restrictions impose severe limitations if analogies are attempted with in-situ cases where geologic discontinuities, inhomogeneities, and irregular boundaries exist. The question might be raised as to the propriety of geotechnically oriented researchers even considering such idealized conditions. There is, however, much to be gained from study of such solutions. The lack of geologic discontinuities and inhomogeneities allows the investigator to separate and leisurely examine such parameters as are included in the solution, without worry of interrelationships of a host of other parameters. Further, elastic solutions have had extensive usage prior to the development of such techniques as the finite-element solution. It is interesting to compare body force solutions with the external field solutions which in the past have been used for design purposes. Finally, the exact solution may be used to verify the accuracy of the finite-element type of solution. The mathematical solution on which this chapter is based was originally developed by R. D. Mindlin.l Because of the complexity and length of the solution, no attempt was made to determine the resultant stress fields until the advent of the present-day high-speed digital computer. How-

Jan 1, 1972

By Michael A. Devane, Neil Duncan

Inclines and tunnels can extend from ground surface to considerable depths traversing a wide range of lithologies. The strata encountered may be affected by loosening and induced stresses at different locations along the route. It is suggested that Phase I of the pre- driving assessment process should include study of the geology, hydrogeology, rock material and rock mass characteristics. A rock mass disruption factor is used to express the ratio of the unconfined strength of intact rock material to the unconfined strength of in situ rock mass. It is suggested that there is a relationship between in situ (secondary) permeability values and the disruption factor, since the permeability of the rock mass is governed by parameters which influence strength. In Phase I1 of the pre-driving assessment, consideration should be given to the prediction of primary loosening which results largely from disturbances to the rock mass arising from the driving process. Also in Phase 11, preliminary assessments are made of the effects of induced stresses and of the geodurability characteristics of the rocks. In Phase 111, the mechanics of various secondary loosening pro- cesses are considered along with their relevance to estimates of stand up time and support requirements. Yield-line analysis is introduced for the study of plastic and brittle type bending deformations. Stand up time and support characteristics are also assessed. In Phase IV, the effects of induced stresses are analysed. It is suggested that even for broken rock in the Yield Zone, the rock mass disruption factor may not often increase above lo which is equivalent to an in situ permeability of 10-1 m/s.

Jan 1, 1983

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage,-and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation. INTRODUCTION Cornucopia is in the southeastern part of the rugged Wallowa Moun-tains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal.

Jan 1, 1939

By Robert D. Lonqyear

SOMEWHAT biased by pride in twentieth century achievements, most of us mining engineers and diamond-drill operators look upon core drilling as a relatively modern practice. The invention of the diamond drill is generally ascribed to Rudolf Leschot, who made use of diamonds in 1846 in drilling blast holes in the Mont Cenis tunnel in Switzerland. In vain we search Agricola and other early writers on mining for signs of diamond drilling. We have, therefore, concluded that it was unknown until the middle of the last century. The trouble with this conclusion, as most prospectors will tell us, is that we "don't dig deep enough"; for it now appears that the archeologists have been putting one over on us for the last fifty years.

Jan 1, 1936

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After Americzn interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and de- clined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1953

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After American interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and declined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1952

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After Americzn interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and de- clined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1953

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By W. L. Saunders

IMPORTANCE OF ROCK DRILLING. IT has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended. annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. 'The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become ,so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 9, 1913

By Wesley G. Josephson

THE MINING PROPERTY of the Argonaut Mining Co., Jackson, Calif., is one of the oldest on the Mother Lode. A vein outcropping on a hill in this section could not long elude the eye of the forty-niner, so it was first discovered in 1850. From that time until 1893 the Pioneer mine, as it was then called, limped along under various poorly equipped and financed operators who tried tapping it by trenching and tunneling. Then the Argonaut Mining Co. took over the property and sank the present 65° inclined shaft in the hanging wall of the vein. The mine workings have now reached the 6000-ft. level, which is 5283 ft. vertically below the surface, or just 3 ft. over a mile. The total production of the mine is uncertain, because of lack of early records, but from 1893 to 1932 it is known to have produced in excess of $17,000,000.

Jan 1, 1932

"The mines of Butte, in addition to the square timber used, consume each year large quantities of round timber, which are called stulls. The Stull business is an important industry, as will be seen from a brief description of the operations of the Mines Timber Co., which institution furnishes most of the stulls and lagging poles used in the Butte mines.Timber produced by the Mines' Timber Co. is mostly cut on the government forest reserve, on California gulch, American gulch and French gulch. To bring the timber to market, a flume 16 miles long has been constructed from Big American gulch to Mill creek. The flume, which heads on Big American gulch, on the Atlantic slope, crosses the Continental Divide at an elevation of 6,525 ft., and delivers timber at Mill creek on the Butte, Anaconda & Pacific railway, which is on the Pacific slope. Timber is loaded on cars at Mill creek and shipped to the Butte mines, a distance of twenty-six miles. There are 29 trestles on the flume line over 25 ft. high. The highest trestle is 78 ft. and the longest is 775 ft. The longest tunnel on the line of the flume is 565 ft. from portal to portal."

Jan 1, 1913

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine's total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By E. Wainer, K. D. Burnham

A wet beneficiation technique for producing wollas-tonite from its ore in high yield and purity has been evaluated in a pilot plant operation at the rate of 75 tons per month. Finely crushed, unsized wollastonite ore mixed with water is passed through a high in tensity oscillating wet magnetic separator of unique design and in a single pass over 90% of the wolla-stonite exhibiting a crystal purity of 99.8% is obtained irrespective of size of feed fraction. Thereafter, the material is processed by closed cycle standard wet milling and classification techniques to yield a 1µ size product, though any mesh size up to and including 50 mesh may be obtained, if desired. Costs appear to be significantly lower than those available from dry processed techniques. Wollas tonite made by this unusual wet process appears to have potential utility in the following fields: ceramics, paints, plastics, paper, organic finishes, reinforcement of portland cement items, controlled porosity refractory ceramic foams, cinder and concrete block paint, and the like. The 1µ and certain chemically processed varieties of wollastonite may have unusual utility in the paper industry both as a filler and as a coating material and in the organic finish industry. Extensive deposits of wollastonite ore equivalent to an average tenor of 50% to 60% of this latter mineral in easily separable form exists in and around Essex County in northern New York State in reserves of the order of several tens of millions of tons. While important portions of these deposits are susceptible to open pit mining techniques, one operation near Wills-boro, N.Y., involves tunnel mining and dry milling and beneficiation techniques. This mill and tunnel mine is presently being operated by The Cabot Corp. and a variety of particle sizes are now sold into markets in the ceramic, paint, plastic finish, floor tile and in similar fields in substantial tonnages on a repetitive basis. Serious investigation and study over the past several years has indicated that, outside of the obvious economies of open pit techniques for mining purposes, wet beneficiation and milling procedures applied to the ore not only represent a potential for greater economies in the production of a superfine finished product but yields products of improved properties exhibiting increased market potential which may not be available from the dry ground product. The Lewis and Deerhead deposits, controlled by the Adirondack Development Corp., appear to be identical to the Wilisboro deposit. Utilizing ore taken from the Lewis and Deerhead deposits, a pilot plant process for the wet beneficiation, milling and classifying of wollastonite ore has been operated for several months. After scalping a marketable garnet product from a minus 16 mesh dry crushed feed on a high intensity roll magnet the balance of the material is then roll crushed in a closed cycle until it will pass a 50 mesh screen. The product constitutes the feed of the wet magnetic separator. The heart of the new beneficiation process is a cyclically operated wet magnetic separator which exhibits the unique feature that unsized feed is easily handled. Product yields of higher purity are equal to that obtained with dry magnetic separations which use closely sized dry ore and multiple passes, but only produce wollastonite of about 98% mineral purity as determined by sink float techniques. It was anticipated that the wet processing through the grinding, milling and classification stage would yield a low cost 1µ ground product which should make available greatly increased applications for the mineral beyond those presently enjoyed. The improved purity was also expected to provide coarser sizes which might be utilized as a raw material for chemical modification which again would expand the uses of wollastonite. The evidence thus far collected appears to indicate that this premise may be expected to be fulfilled. There are on the surface of wollastonite particle sites at which cheinical reactions may occur1. It is believed that wet ground material provides a better base which will allow wollastonite a deeper entree into the field of chemical raw materials. Wet ground at 20µ and finer permits with certainty a number of chemical reactions, some of which are mentioned later in this article. While well crystallized wollastonite makes up the majority of the ore, the balance consists mainly of very weakly magnetic diopside of the hedenbergite-

Jan 1, 1965

By W. L. Saunders

It has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 1, 1914

By George J. Clark

One of the major problems of operation in the anthracite industry is the disposal and handling of refuse—not because of its complexity but because of the quantity and type of material involved. It is the purpose of this paper to describe the kinds of refuse, methods of disposal, quantities of material to be handled and equipment used, together with present day application at specific operations in the Northern, Eastern Middle, Western Middle and Southern anthracite fields. For the purpose of this paper, refuse is considered to be any material that has no present or foreseeable future value and that must be handled and disposed of in the process of mining and preparing anthracite for market. Included in this classification are tunnel rock, mine rock, cleaner plant refuse, breaker refuse, old timber, ashes and silt. Disposal Methods Old timber is disposed of either by burning or by depositing on the refuse bank. Burning is preferred because timber on the refuse bank is a potential fire hazard. Ashes are deposited on a separate bank, mixed with other refuse, or flushed into old mine workings. In many places, the latter practice has caused considerable difficulty in preparation of coal mined from these areas. In depositing ashes on the surface, it is wise to refrain from mixing them with material containing coal as such contamination may prevent reclamation of the coal in future years. Tunnel work, mine rock, cleaner plant and breaker refuse compose the bulk of the material to be disposed of and handled, and are referred to collectively as "refuse" in this paper. Waste material in or adjacent to the coal beds may be removed at the working face wherever possible. This can be done in flat or lightly pitching beds, and in the Northern field represents a sizable percentage of this type of refuse handled. In the other three coal fields, this method of disposal cannot often be used. Refuse not removed at the working face is taken to the surface and generally is deposited on banks; occasionally it is crushed and flushed into old mine workings. Breaker refuse often is used for constructing berms for silt-retention basins. Disposal Problems The problem of handling refuse is different for each operation, owing to topographical conditions, quantity of material to be handled, anticipated requirements and types of equipment in use elsewhere at the operation. Preparation plants with limited refuse-disposal areas, excessive grades to reach the required elevation and long hauls to disposal areas not readily accessible require the selection of equipment to best meet the conditions. The quantity of refuse to be handled from a given amount of raw material varies considerably throughout the four fields. In mine coal, this varies from a low

Jan 1, 1949

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By D. L. Feucht, R. L. Longini

The semiconductor heterojunction is considered in terms of simple models which may lead to an understanding of move complex heterojunctions. Metallurgical and electrical properties of hetero-junctions aye discussed including the interface structure, energy -band diagram, and carrier transbovt across the interface. It is found that in a heterojunction all mechanisms such as injection, tunneling, and junction recombination found in simple junctions play modified voles. INTERFACES between materials (grain boundaries, the electrical junction between two differently doped materials in a single crystal, the oxide-metal interface, or metal-metal junctions) are of considerable importance in many situations. These various interfaces all have one very fundamental thing in common. Quantum mechanically speaking, the wave functions of the electrons in one material may penetrate the other material but, in general, only to the extent of angstroms. From an electrical point of view the conduction mechanism changes as a current passes through such junctions. In some cases the change is tremendous, in others almost negligible. The interface, then, is the locus of a change of conduction mechanisms. Some of these, particularly in semiconductors, are well-understood. The ordinary p-n junction in a single crystal can be the locus of an injection mechanism or a tunneling process, depending on conditions. The mechanisms are probably best understood in semiconductors because of the possible simplified view of particlelike conduction. The bands are either nearly filled or nearly empty and band overlap is seldom involved. The same fundamentals are probably important in other situations too but they are very difficult to look at naively. Although the simple look at the semiconductor case only gives us a relatively rough picture which must then be refined, the other systems, which involve a more complex situation, immediately are in many ways too difficult. There are too many initial choices of complex systems and therefore it is not possible to be even reasonably certain of any one model. Because of the relative simplicity of semiconductors, their good and controllable structure, and because of the ability to make many measurements on them not normally available to either metals or insulators! they are probably the best understood materials. It is therefore desirable to use them as a tool to further the understanding of interfaces in general. Semiconductor-heterojunction concepts were first proposed by kroemer1 in 1957. This was followed several years later by reports on the fabrication and experimental characteristics of heterojunction structures by Anderson2 and Diedrich and jotten.3 I) THE HETEROJUNCTION STRUCTURE To get down to hardware, when we refer to a semiconductor heterojunction we imply that there exists an intimate contact between different semiconductor materials. We could put two pieces of material together, complete with oxide layers, we could remove the oxides, or we could even melt the interface and hopefully get wetting and a good "bond" on solidifying. In fact we could by some means grow a crystal of one material using the other as a seed. Essentially we are interested only in the last two because they are the simplest to look at analytically. The degree of perfection of fit varies greatly and is reflected somewhat in the arc welder's joint strength. The lattice match of the two materials, their orientation, and so forth. is obviously necessary for a good bond but so is the continuity of any polar bonds which are involved such as in the III-V semiconductors. The mechanical misfit between two similar lattices can be described in terms of edge dislocations. The edge-type dislocations must be very close together for the usual misfit and there must be dislocations for each of several different Burger's vectors in order to produce a lattice match. The .'dangling bonds'' resulting will be involved in producing interface charge. Order of magnitude estimates of the charge density extrapolated from low densities of dislocations in homogeneous materials give 5 x 1013 cm-2 Ge-Si and 1 X 1012 cm-2 Ge-GaAs electronic charges. Edge dislocations also act as very active recombination centers between holes and electrons. One lattice "matching" difficulty usually exists even if two structures have essentially the same lattice constants as they will have different coefficients of therma1 expansion. Thus, on cooling from the usually high temperature of fabrication to room temperature, dislocations are produced, a good fit not existing at both temperatures. In brittle materials this shrinkage may even result in cracking. For the Ge-Si interface the mismatch is about 2 x 10 -6 per degree whereas it is less than 10"7 per degree between germanium and GaAs. The exact effect of the misfit is dependent on the thickness of the materials involved. For a very

Jan 1, 1965