Search Documents

CSA mine, which is a deep level copper operation, located 12 km north of Cobar, NSW, currently uses a top down stoping method, utilising cemented hydraulic backfill (CHF) to fill and stabilise the stoping void thus assisting the extraction sequence. The stope sequence then requires development back through the CHF stope so that the necessary infrastructure for the subsequent stoping, such as raise bore pads can be sited. The primary and secondary support installed in the CHF consisted of 100 mm thick fibrecrete from floor to floor with 7 + 2.4 m long resin support tendons installed at 1.5 m ring spacing. This support system relied on the resin achieving a quality bond with the CHF, and also the fibrecrete developing early structural strength due to the use of an accelerator. In addition to the delays in the excavation turn around time, it was felt that a superior support system could be designed. Such a system was designed; risk assessed, tested underground, and trialled in selective CHF digouts, and eventually signed off as the chosen support method in CHF digouts. This paper discusses the change from a passive support system used in CHF digouts to an active support system using Swellex bolts and weld mesh, which has provided an active support system, that is superior, faster to install, reduced the excavation turn around time and is overall a cheaper support system.

Nov 25, 2010

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

This paper first describes the essentials of the slurry shield method and its achievements, then problems encountered during driving tunnels and their countermeasures, and finally shows problems to be solved in the future. The author works at Tekken Construction Co., Ltd. as a director. All the data cited are based on material gained from the slurry shield tunneling works undertaken by the said company. The mark, viz*, indicates that Tekken Construction Co., Ltd. has obtained or is applying for a patent in the U.S., Europe and Japan. 1. CONSTRUCTION RECORDS BY SLURRY SHIELD METHOD AND ITS PROBLEMS (1) Shield machines in the future should have the following characteristics; a. to be able to drive less cohesive soil b. to make no change to the ground water table level c. to make it possible to let people work in normal air pressure d. to cause less settlement at the surface To meet the above conditions various kinds of mechanical shields have been are tried, viz. limited air pressure type, rotary cutter with slit regulator, screw-discharge type, blind shield, etc. As far as the author knows, however, they are not 100% successful. Tunnels need their own accuracy in accordance to the usage. Both ease of driving

Jan 1, 1976

By A von Johannides, G J. van Hout, L F

In the past various systems have been used to plan the extraction of ore from block cave operations. These systems have varied from rather sophisticated models with empirical ægravity flowÆ rules applied to the very rudimentary models where only the recorded mined tonnageÆs have been accounted for against the available resource. The normal requirement of these models has been to only plan the movement of ground through the drawpoints. Little cognisance has been taken of the other parameters that affect the total mining operations. The intended purpose of the linear program planning system is to not only include the management, resource availability and geotechnical constraints, but to also include the mining rules. The paper will discuss the various constraints that have been considered, and attempt to illustrate where the system better serves the production system than previous ones. A brief technical discussion on the linear programming system is included.

Jan 1, 2000

The current economic climate and demand for iron ore has resulted in mine operators being prepared to accept aggressive slope designs and associated failures provided that they can be quantified (ie volume of failure and clean up costs, etc) and incorporated into the mining costs, at a feasibility study level. This has numerous implications for pit slope design/geomechanics. Typically when geotechnical engineers conduct slope stability modelling a single value, usually the average or mean value for model input parameters (ie structural orientations, material properties and hydrological conditions) are chosen. The implications resulting from using a single value for model input parameters will vary depending on how the modeller has chosen the value, ie should the modeller choose a mean value from a log-normal distribution of material strengths an optimistic representation of the stability may eventuate, consequently if the designer decides to conservatively downgrade the values by a nominal factor, a pessimistic representation of slope angles may occur, which would result in excessive stripping and mine development costs. A more realistic and representative way to model the inherent variability of geological/geotechnical conditions would be to do so probabilistically. Whereby the modeller can assess the variability of the geological structure as observed/recorded during the core logging process and a similar approach for the material strength properties. The final model output would be a distribution of factors of safety in relation to overall slope angles, ie probabilities of failure for individual slope angles could be determined. This output (graph) could be modified by the mining engineer to incorporate mining costs as well as clean up costs for the respective slope angles and associated failure volumes, ie probabilities of failure. The author intends to provide a detailed overview of the processes involved in deriving a geotechnical design, ie; starting from the data collection phase (core logging/face mapping), through to the data interpretation and formulation of slope parameters; determining the variability and uncertainties associated with each of the process; ensuring that it is adequately captured in the model input parameters; and how the mining engineer could utilise this information to derive final feasibility study mining costs.

Jan 1, 2009

By P B. Hills

Almost a quarter of a century since Bridges (1993) documented techniques for the assessment of ground conditions in a seminal paper in the Proceedings Second International Mining Geology Conference, the necessary role of the geologist in recording geotechnical data on exploration properties and in mines remains. Typically, the geologist is the first professional on the exploration property. Of course, most exploration properties don’t become mines. However, when a property does start to come together and form a coherent mineral deposit and professionals from across the minerals industry spectrum, including specialist geotechnical engineers, become increasingly involved, it remains the geologist who has the most intimate knowledge of the deposit. By association, that knowledge extends to the character of the rock mass.Throughout the various phases of prefeasibility, feasibility, construction and production, culminating in the mature mine, the knowledge of the rock mass held by the geologists continues to grow. In the current era of minimising cost and optimising profit, meeting the requirements and expectations of stakeholders ranging from fellow employees to investors, industry and financial regulators and the broader public, in a social environment where occupational health and safety concerns are of uppermost concern in every endeavour, the value of the geologists’ observations cannot be understated. Mines nowadays employ more geotechnical engineers than they did in the early 1990s when Bridges (1993) wrote his paper. More funds are available for specific geotechnical investigations of exploration properties and mines; none-the-less, those programs remain limited in their extent and there is a wealth of additional data available for collection with the appropriate training, at little additional effort. Fundamentally it is all about the numbers. Any hole not geotechnically logged is a hole that will need to be drilled again if the data is required. Any face, surface or underground, not geotechnically mapped is one that may need to be mapped a second time. That doesn’t mean every hole or every face. However, it is the proposition of this paper that the opportunity for additional geotechnical data to be gathered during traditional geological investigations is an opportunity that cannot be ignored. Occupational health and safety requirements demand that the geotechnical risks associated with mining are appropriately managed. Mining regulations in most Australian and overseas jurisdictions requires the consideration of geotechnical risk through formalised management plans. The Joint Ore Reserves Committee (JORC) Code requires the consideration of modifying factors more than ever before. The benefit to be realised through improved geotechnical understanding by geologists on the ground leads to improved occupational health and safety, optimised reporting compliance, and improved financial and social outcomes for the exploration property and ultimately for the mine that follows.CITATION:Hills, P B, 2017. The necessary role of the geologist in geotechnical data gathering, in Proceedings Tenth International Mining Geology Conference 2017, pp 347–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By E Rubio, N Morales

A common practice in the mining industry is to decompose the planning process into different tasks, so the overall process and specific schedules can be constructed easily. Nevertheless, currently there are some adverse effects, such as not capturing the real value of a project by not taking into account the construction of several underground drifts and general infrastructure. Then the common practice is to compute mining sequence and cut-off grade profiles over the life of the mine without constitutively integrating the development schedule as a means to measure the constructability of a given mine design and sequence. Thus, the investigation summarised in this paper shows a novel, integrative way of treating an underground mine sequence and production schedule while considering drift development scheduling. Moreover, it is thought that, because of this original model, the whole underground production scheduling exercise must concentrate on combining the development and the production scheduling to compute a robust and a feasible production schedule.In order to quantify the effect of the conventional way of viewing the planning, the concept of the building information model (BIM) needs to be used, which was postulated by Charles Eastman and has been used extensively since the late 1970s. BIM takes other aspects of a project into account, considering at the same time the spatial relationships, quantities and properties of building components, but especially some kind of model visualisation, which is the advantage to be incorporated. This paper presents the basis for an optimisation model that allows for defining the sequence of the mining development so that the production plan can be achieved. For this, the model considers the space dimensions, time, pattern or strategy, cost or benefit, precedence and resources available. Tests were performed considering a block caving and sublevel open stoping method. Finally these tests showed the main conclusion, that production sequence changes when the building capacity is considered.

Sep 26, 2011

By C Zhang, I Canbulat, G Fan, D Zhang, C Wang

A clear understanding of the intensity of coal and rock burst is the basis for future research on burst mechanism and control. There has been a wide variety in the description of coal and rock burst damage at different countries using multi-methods, which makes the common understanding even more challenging. Therefore, this paper presents a broad review on the quantifications of intensity of coal and rock burst and seismic risk around the world, considering critical factors including seismic energy, magnitude, peak particle velocity and ejection velocity. It is found that the seismic energy of coal and rock burst can widely range from 0.002 MJ to 60000 MJ, with equivalent Richter magnitude from -1 to 4. The daily seismic energies can be used for seismic risk potential assessment, with energy levels from 0.1 KJ to 10 MJ, which is much lower than the burst sources. The magnitude of the seismic events can be also estimated based on the weight of damaged coal mass and human senses of vibration and sound. For the seismic intensity represented by peak particle velocity (ppv), it keeps constant within fault radius and attenuates with a speed of 1/r4 and 1/r in near and far field respectively, thus it is possible for a small seismic event to induce considerable ppv causing severe damage if the epicentral distance is small enough. There has not been a strong correlation between the ejection velocity and ppv, as seismic energy is only one of the energy sources that contribute to the kinetic energy of burst damage. CITATION:Wang, C, Zhang, C, Canbulat, I, Zhang, D and Fan, G, 2018. Intensity quantification of coal and rock burst risk – a review, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 223–233 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By J Nixon

I have to say that my story is not too much different to many others who grew up and worked in the great mining fields like Broken Hill, Mt Isa, Rosebery, Kalgoorlie or Kambalda and any one of them could have stood up here and spun you a good yarn.What does my paper offer you in this volume? By sharing my experiences I want to encourage you to consider your own experience with leadership, taking on change, learning from and contributing to the development of others.I have been very fortunate to be part of many new innovations into underground mining over the past 40 or so years; most of it with Conzinc Rio Tinto Australia (CRA)/Rio Tinto operations.•From hand-held drills and a homemade single boom Jumbo mounted on an old Airtrak, to the sophisticated twin boom jumbos with high speed drifters all controlled by an on-board computer;•from a Scraper winch and a Wagner 2D loader to fully automated electric LHDs that navigate to the tipple, empty the bucket and return to where they come from;•from hand-held cut-and-fill and timber stoping in Broken Hill to the bulk mining methods of a block cave where at Northparkes we mined more ore in a month than we mined in the total five years of operations at Currawang;•from hand-held scaling and bolting with no skin protection to installing ground support with Jumbos and sophisticated Cable Bolters and the introduction of in cycle shotcrete;•from hand-held ladder rising and shaft sinking to Box Hole rigs, Raise Bore Machines and Blind Hole shaft sinking; and•from Gelignite based AN60 stick explosives, ANFO, fuse firing and half second detonators to Powergel, Emulsions and electronic computer programmed detonators that can somehow be initiated by ‘Blast Ped’ travelling through the rock.

Mar 21, 2011

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S Sabanov

Supplementary sampling of particulate mass concentration, the number concentration and the average particle diameter of nanoparticles using a TSI Dust-Trak DRX Aerosol Monitor, Naneos Partector 2 has been conducted. The aim of this study was to evaluate suitability of the instrument for long-term monitoring of diesel particulate matter (DPM) at conditions of polymetallic mines. Sampling was conducted in an area of the active ore heading, requiring the use of a diesel-powered face haul-age loader R1700 and a mine truck Caterpillar AD-45. The sampling was done for 126 minutes at a distance of 30 metres from the mine face. Results of this field work can be used to expand the sampling program to other mines. Expected outcomes of this study are to develop costeffective DPM control strategies, improve mine ventilation, and protect mineworkers’ health.

Oct 12, 2022

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C Robertson, J Campos

The South African mining industry first experienced en-masse use of electronic detonators in the Narrow Reef environment using AELÆs ElectrodetÖ pre-set delay system. In recent years, programmable systems such as AELÆs SmartdetÖ have also established their position, and within both AEL and the mines there has been important learning around the strengths and weaknesses of these systems. In general, the fixed delay systems tend to be more easily appreciated by less-skilled work teams, and are very well suited to simple layouts, especially long, narrow blasts. However, development of programmable row controllers and series delay inserts has greatly expanded the field of usefulness of these systems while retaining most of the simplicity of use. The programmable systems are immensely flexible and therefore able to function under any condition, but require a higher level of discipline and knowledge. Much has been done to address this issue and make the systems user friendly, so the systems have converged to some extent. These systems are both valuable tools for achieving control over blasting in underground and surface applications. The choice of system is very dependent on the prevailing conditions. Accurate timing with electronic enhancements continues to show an increasing range of benefits to mining operations. There is a strong parallel with non electronic initiation systems which helps to understand the appropriate use of the systems.

Jan 1, 2001

By D La Rosa, G Power, K Riihioja

In underground mining, the often unpredictable variability in ground conditions may lead to the application of suboptimal drilling and blasting patterns, resulting in poor performance. Experience and pertinent information to develop and implement improved drilling and blasting strategies can be easily lost due to the lack of means to help engineers store, access and manage this information. The Julius Kruttschnitt Mineral Research Centre (JKMRC) through a series of industry funded applied research projects has been developing a system that can facilitate the drill and blast design, analysis, auditing, documentation and data management processes. The system is a hybrid between an information management software module called BMS (Blast Management System) and two design and analysis modules, 2DRing for underground production blasting activities and 2DFace for development blasting activities. A concise description of the software tools and its applications are given in this paper, supported by two case studies. Opportunities to further develop the software are also highlighted, they include options to integrate these tools to existing drilling and blasting automation systems and portable computing technology to facilitate the design, implementation and continuous improvement processes.

Jan 1, 2001