Search Documents

The reasons for using SFRS, including the way a SFRS performs in comparison to plain shotcrete as a support element in mining tunnels, are discussed. The mechanisms by which steel fibres reinforce shotcrete and the need for specifying performance criteria are highlighted. A description of current testing procedures, including an overview of æquantitativeÆ design recommendations provided from various international authorities, is provided. A summary of international recommendations on suitable æqualitativeÆ performance classifications is also reviewed, including a critique of their suitability. Finally recommendations on the practical considerations necessary to ensure good quality, in-place SFRS, are made, including a calculation method for determining minimum steel fibre dosages.

Jan 1, 1999

By Howlett P. F, Courtley S

A problem with secondary breaking at one of the mines of Pasminco Mining led to a study of new rock breaking technologies. Many of the techniques being developed had emerged from the thrust in the USA for continuous drill=break excavation. Such approaches to rock breaking highlighted the applicability of what would normally be classified as tunnelling techniques, to the secondary breaking sector - and possibly the reverse. As a direct result of the investigations for suitable technologies, Pasminco Mining supported the development of two improved rock breaking methods specifically targeting secondary breaking, one of which could be applied to continuous excavation.

Jan 1, 1993

By Seedsman R

The fundamentals concepts of roof support are similar between coal mining, metal mining and tunnelling and yet there are different design approaches, different hardware, and different levels of site investigation. This should not be the case and this paper discusses the key geotechnical issues that should underlie all roof support design - the need to reinforce defects. A design method to build a beam in laminated rock under high horizontal stresses is presented. The method allows for changing rock strengths, defect properties and varying horizontal stresses. At one level the design can be implemented with design charts and tables. Lessons learnt during the implementation of the designs at 5 different mine sites are Discussed.

Jan 1, 1998

By Smith T

Bacterial oxidation is often attributed with the advantage that a high level of gold recovery can be obtained at a relatively low level of sulphur oxidation. This is sometimes attributed to the bacteria "tunneling" towards gold inclusions, however it is often due to the presence of two or more sulphides of differing gold content which leach at different rates. Gold is liberated from the individual sul- phides linearly with oxidation. The distribution of gold between pyrite and arsenopyrite in two samples taken from a prospective gold resource was examined. The two samples showed differing responses to bacterial oxida tion and it was shown that this was due to differing intrinsic gold grades in the mineral phases and differing proportions of the minerals in the two samples.

Jan 1, 1991

By Warren M

Many Australian tunnelling and mining companies regularly investigate different methods or equipment in an attempt to keep ahead of their competition. Sometimes the result is a new approach or process which wins a tender or provides an advanced solution to a problem.The Australian Government has a policy of encouraging forward thinking among Australian companies and provides a range of incentives. One of these incentives is currently available retrospectively to 1985 - 86, and the registration process is relatively simple with only one form to be completed. Companies who investigate methods of raising productivity could be reimbursed for the costs of the investigation.

Jan 1, 1993

The concentrated efforts now being directed towards the development and application of monitoring and control techniques have now resulted in their widespread use in UK mines together with evidence of benefits resulting from their application. There is little doubt that the longwall method of producing deep mined coal will continue but will be made more reliable and efficient with the aid of control technology. The major fields of research and development work are concerned with planning and design of mines and mining equipment; management and engineering information; and automation of coalface, tunnelling and transport systems. The principal achievements now in widespread use are: the standard computer system MINOS, widely applied to mine transport, coalfaces and mine environment; extensive use of machine condition monitoring leading to condition-based maintenance; underground automation of conveyor systems and guidance systems for ranging drum shearers and boom-type roadheaders are being widely introduced.

Jan 1, 1985

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

By Yokozawa K, Yamamoto T, Kameoka Y

Japan Construction Method and Machinery Research Institute has been conducting various field surveys of tunnel works and other excavation works, and the cost and efficiency of these two excavation methods have been studied. Based on these data, the costs of blasting excavation and mechanical excavation represented by roadheaders were calculated. The costs were calculated and compared for rocks of various hardness. When the total construction cost is considered, the degree of overbreak becomes one of the most influencial factors, because the overbreak area must be filled up with expensive shotcrete in NATM. So, in the next step, the relation between the excavation costs considering overbreak and the rock hardness was studied using the data on overbreak obtained by the field survey.

Jan 1, 1987

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Phillips H. R

The action of free rolling disc cutters is well understood, relationships between disc geometry and performance having been established both in the laboratory and under field conditions. However, under severe operational conditions a malfunction of the disc bearing assembly is likely to produce a definite change of cutting action. Collapsed or siezed bearings can even prevent the disc from rolling and thereby create what is equivalent to a drag pick. This paper describes a programme of laboratory experiments using deliberately stalled discs. Their performance under such conditions is contrasted with that for a free rolling disc and also with a drag pick having a ridged front developing into a negative radiused back clearance angle. In conclusion an assessment is made of the influence stalled discs can have on the torque and thrust requirements for a tunnel boring machine.

Jan 1, 1981

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By Yesil MM, Bozdag T

The swelling process is an impor- tant problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from oedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the oedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Hart J. G, Anderson J. S

The presence of platinum metals in the nickeliferous copper ore of the Thomson River Copper Mine near Walhalla, Victoria, was first revealed in 1905 by assays made in the laboratory of the Department of Mines (1).These disclosed the presence in the ore of 5 dwt. platinum metals, 1 dwt. gold and 13 dwt. silver per ton. Attempts to isolate the platinum-bearing mineral were unsuccessful, and the absence of obvious native platinum led the assayer, Mr. P. G. W. Bayley, to suspect that the platinum might be present as sperrylite. Subsequently, Mr. C. M. Lyons, then metallurgist to the Long Tunnel Gold Mining Company, Walhalla, tried to isolate the platinum mineral from samples of ore containing as much as 7 dwt. platinum metals, but again without success.In 1912, a sample of copper matte from this ore was submitted to Messrs. Johnson, Matthey and Company, Limited of London, for analysis. The analysis, which is quoted below by their courtesy, revealed tnat a large proportion of the metal pi'eviously reported as platinum was palladium, there being about two parts of palladium in the matte to one part of platinum.

Jan 1, 1942

Geosynclines have been well studied for many years, but very little has been written about the concepts of sedimentary basins in spite of the vast amount of data available. They have been regarded, perhaps, as well- understood intuitively, and therefore not worthy of study. Many of the fundamental concepts of geology were developed during the 19th Century with the construction of coal mines, canals and railways. It was a happy chance that led railway engineers in the early days to think that trains could not climb any but the smallest gradient, so, in Britain at -least, numerous railway cuttings and tunnels were made. These exposed to view and study, in a better form than Nature usually provides, a great deal of interesting geology. Because of the lack of literature about the concepts of sedimentary basins, it is not possible to be sure what the early geologists thought. It seems that sedimentary basins were regarded as recording a history of subsidence during the early stages, when a transgressive sequence accumulated; and a history of uplift during the later stages, when a regressive sequence accumulated. It seemed axiomatic that the age of folding and faulting was younger than the rocks folded or Faulted.

Jan 1, 1987

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992

Development of the Greenvale orebody, containing 40,000,000 tonnes of nickel ore, began in 1971 and production commenced in 1974. Annual capacity is 2,800,000 wet tonnes. The variations in ore grade and physical characteristics which occur throughout the ore- body had a major influence on the selection of mining methods, grade control procedures, and equipment. After removal of overburden by scrapers, ore is excavated by draglines sidecasting into windrows. Feed to the crushing plant is .reclaimed by front end loaders into rear dump trucks according to a grade selection pro- gramme. After crushing, ore is stockpiled into blended units of ore of required quality. Ore is stacked and reclaimed for train loading using techniques designed to give maximum mixing of ore characteristics through Bach unit. These procedures are repeated on discharge at the plant site at Yabulu. The railway, constructed by Queensland Nickel Pty. Ltd. to Q.G.R. standard, and operated by the Q.G.R., is 216 km long and includes eight major bridges and three tunnels. Two trains per day, one of four locomotives and 92 waggons, and one of three locomotives and 69 waggons, haul crushed ore to Yabulu. Train loading is semi-automatic. A small township and associated services have been constructed for employees at Green- Vale.

Jan 1, 1974

In the hard rocks of the Nordic countries of Norway, Sweden and Finland underground works have a long tradition. Today the subsurface has been taken into use for a wide variety of purposes. In this paper only the more uncon- ventional examples are described such as caverns for drinking water, sand bunkers, molasses silos, wine and liquor stores, cold stores, heat storage, waste disposal and state archives. The particular use of unlined high pressure tunnels and socalled air-cushions for hydropower schemes is discussed. The dual use of subsurface air-raid shelters for sports activities seems to be a special Nordic tradition. Some cost figures are given and the advantages of using the underground is Discussed.

Jan 1, 1987

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012