Search Documents

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By P Campi, M Dodds

The EastLink project is a 39 km tollway to the east of Melbourne and includes twin three-lane 1.5 km driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley to help preserve the unique flora and fauna in the area. This paper describes the process of transferring the support requirements from the ædrawing boardÆ to the tunnelling face by integrating the temporary support design with the contractorÆs tunnel excavation and support procedures, including sharing of responsibility between the designer and contractor for selection of the support type and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. The methods developed during the design phase incorporated a formal system of reviews, support selection and feedback by monitoring tunnel and ground responses. During construction, the process was implemented using a set of simple documentation and regular structured communication between the contractor and the designer.  

Jan 1, 2008

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Munro

he Melbourne City Link project will complete a missing link between two existing major freeways in the Melbourne road network, providing a much needed bypass of the Central Business District for through traffic. The project, which is being financed under a BOOT arrangement with the Victorian State Government, involves the upgrading of significant stretches of existing freeway and the construction of new sections involving viaducts and tunnels. The tunnel sections, which are the focus of this paper, are beneath residential and business areas, the Yarra River, the Royal Botanic Gardens and significant sporting facilities where surface construction would be either impossible or unacceptable (reference Figure 1). The shorter, 1.62 km west bound Domain tunnel comprises two cut and cover sections through Olympic Park then the Yarra River, the driven section of 0.68 km length and exits through a common cut and cover section with the east bound tunnel under St Kilda Road and Sturt Street. The longer 3.76 km east bound tunnel commences at the common portal, through cut and cover under St Kilda Road then 2.86 km of driven section before exiting at a cut and cover section at Burnley. The longer Burnley tunnel has an access and ventilation shaft at approximately its mid point.

Jan 1, 1999

By R Fletcher

Pacific Hydro, a leading renewable energy company from Australia, is developing a series of cascading run-of-river hydro electricity projects in the Cachapoal Valley at the base of the Andes Mountains some 100 km south of Santiago in Chile.These projects involve extensive tunnelling and underground works. The first of these projects is called Chacayes (110 MW installed capacity) and is now under construction with Astaldi SpA of Italy and Fe Grande of Chile as the EPC contractor. Astaldi SpA also has an equity stake in the project. It involves 6 km of tunnels between 5 m and 7 m diameter, of which 2.3 km is by tunnel boring machine (TBM) (5 m diameter).This paper outlines the local and regional geology, the scope of the Chacayes project, actual tunnel excavation rates and support, and compares the decision making on Chacayes between a choice of traditional drill and blast excavation versus TBM.The paper also outlines the next project planned to be developed by Pacifi c Hydro in the valley – the 140+MW Nido de Aguila project involving a main tunnel drive of 11 km with two intermediate adits, plus a 388 m shaft and underground powerhouse. The main tunnel drives are likely to be excavated by two hard rock TBMs (5 m diameter) but will need to be able to withstand high overburden pressures of up to 1300 m.Subsequent projects in the planning stages include the downstream Coya II project with two tunnels totalling approximately 10 km, one of which may be by TBM.

Mar 8, 2011

By A Kindred

The Bogong Hydropower Development is a 140 MW high head power project currently under construction in Northern Victoria. The project is the final link in the Kiewa hydroelectricity scheme, which was originally constructed in the 1950s. Due to its location in the Alpine National Park, the waterway for the Bogong project must be located entirely underground. A series of shafts and tunnels is being constructed to transfer the water from the headworks at McKay Creek to the new power station located on the shores of Lake Guy in Bogong village. The difference in elevation between the headworks and the power station is greater than 420 m, which poses particular issues for the design and construction of the waterway. The purpose of this paper is to describe the design and construction planning aspects of the tunnelling and shaft excavation and lining works for the waterway. The tunnelling works includes 5.7 km of hard rock tunnel boring machine (TBM) driven tunnel, 1.1 km of drill and blast tunnel and two deep shafts. The tunnels and shafts are lined with a mixture of permanent rock bolts and shotcrete, concrete lining and steel lining. The viability of the Bogong Hydropower Development relies heavily on the ability of the TBM to excavate at high speed through the East Kiewa Grandiorites. Particular attention was given during the construction planning stage to understanding the excavation characteristics of this material, and designing a suitable hard rock TBM that would be capable of meeting the program requirements of the project.

Jan 1, 2008

By G Marling, A Calderon, J Harris, P Kirsch, M Shi, D Sprott, A Kirsch

Large-scale infrastructure construction needs to comprehensively manage risks that can impact the health and well-being of many people, from workers (temporary, contracted or full time), to families and surrounding communities. This paper starts with an analysis of incidents (injury, fatality, other damage) in tunnel construction between 2000 and 2014 and assesses the distribution of these events by continent, year, and severity of outcomes. These incidents are then analysed and mapped to a framework of hazards derived from RISKGATE (2014). A comparative register of current tunnel construction risk management guidance is derived from current Australian codes of practice and this register is also mapped to the RISKGATE framework of hazards to identify where coal industry knowledge may offer utility to the tunnelling industry.An initiative of the Australian Coal Association Research Program (ACARP), RISKGATE is an interactive online risk management system developed to assist the mining industry in implementing continual improvement in the management of major unwanted events. To date, a comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, outbursts, coal bumps and bursts, human/machine interface, manual tasks, slips/trips/falls, inrush and occupational hygiene. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper proposes and outlines how knowledge within the RISKGATE platform could be applied to managing the significant health and safety risks associated with tunnelling. The authors suggest that to varying degrees the knowledge already captured in RISKGATE is likely to be transferable to tunnelling construction operations. Please note that this paper focuses on tunnel construction and does not address risk management of tunnels in operation (eg road transportation or utility networks).CITATION:Kirsch, P, Kirsch, A, Calderon, A, Marling, G, Harris, J, Shi, M and Sprott, D, 2014. Management of health and safety in tunnelling – application of Australian coal mining knowledge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P C. Miclea

Transportation networks extend every day around the world, requiring safe and well-maintained structures for efficiency and for users’ safety. Due to specific features of the infrastructure, such as longer tunnels, increased traffic and marginal safety rules, fire safety in rail and road tunnels becomes more challenging.The situation becomes more critical due to the global economy and increasing worldwide tourism, with multi-national companies often involved in both design and construction of transportation routes or systems in other countries. Tourism brings the risk of visitors becoming victims in a foreign land; thus, international law becomes more and more applicable to transportation projects all over the world, requiring a consistent approach to safety (UN Economic and Social Council, 2001; US DOT Federal Highway Administration (FHWA) 2006; US Transportation Research Board, Committee on the Role of Public Transportation in Emergency Evacuation, 2008; UK Parliamentary Office of Science and Technology, 1997).There are significant differences between rail and road tunnels, both in their functionality and safety requirements. Most tunnels over a certain length are equipped with emergency ventilation systems capable to control the spread of smoke by creating an air stream in the desired direction. Besides ventilation, fire-life safety (FLS) includes smoke and heat detection by linear or spot detectors, closed-circuit television (CCTV) and public address systems with prerecorded announcements, as well as evacuation signage and monitoring capabilities (Vägverket – Swedish National Road Administration, 2004).There isn’t a consistent, worldwide approach to the design of emergency ventilation systems for tunnels, with significant differences from continent to continent (US DOT Federal Highway Administration (FHWA), 2004, US Federal Transit Administration, Transportation Research Board, 2006). In North America US NFPA 130 and 502 standards for rail and road tunnels, respectively, represent the main criteria, however, they are continually revised and new versions issued every three years. For road tunnels the World Road Association PIARC issues guidelines, but they are not truly enforceable. There are no similar international guidelines for rail tunnels, except general recommendations by the International Association of Public Transport (UITP) (IAPT, 2003).In Europe the Directive #54/EC adopted by European Community Parliament in 2004 requires a minimum level of safety for road tunnels users in all existing and proposed tunnels in the Trans-European road network that are greater than 500 m in length. Authorities having jurisdiction in many other individual countries, such as Australia, Austria, Germany, Japan and others, enforce specific safety regulations (Miclea et al, 2007). While it is impossible to summarise all aspects of this topic in a short paper, a review of the design approach, the existing differences in safety requirements, as well as applicable design solutions to meet safety codes for both rail and road tunnels are discussed below.

Mar 8, 2011

By D Kubik, K The

The New Zealand (NZ) Transport Agency’s Waterview Connection will complete Auckland’s Western Ring Route, a 47 km north–south motorway alternative to Stage Highway 1. The project is being delivered by the Well-Connected Alliance comprising the New Zealand Transport Agency (NZTA), Fletcher Construction, McConnell Dowell Constructors, Obayashi Corporation, Parsons Brinckerhoff NZ, Beca Infrastructure and Tonkin & Taylor.The project involves construction of 5 km of new motorway, nearly half of it underground connecting State Highway 20 (SH20) to State Highway 16 (SH16). The underground portion of the project incorporates twin 13.2 m inside diameter (ID) tunnels 2.4 km long, each carrying three traffic lanes, one for north-bound traffic and one for south-bound traffic. The tunnels are being driven by a 14.46 m outside diameter (OD) 2400 t, tunnel boring machine (TBM) shield that was assembled and launched at the southern portal. It will be turned and re-launched at the northern portal for the return drive to the southern portal where it will be disassembled. This paper presents two major temporary works elements contributing to the successful launch of the TBM: the TBM assembly crane platform and the TBM shove frame and associated components.Tunnel boring machine shield assembly – crane platformThe TBM shield was delivered to site in subassemblies ranging in weight from 100 to 380 t. It was initially proposed to use a 750 t crawler crane sitting above the tunnel portal headwall to assemble and disassemble the TBM. However, this did not have sufficient capacity to allow the TBM shield to advance clear of the tunnel before disassembly commences. To reduce the crane’s working radius a temporary steel crane platform was developed that is supported on the side walls of the tunnel approach trench. This has enabled a smaller, less expensive, 600 t crawler crane to be used and will allow the TBM shield to clear the tunnel before disassembly.Tunnel boring machine launch – temporary worksTo launch the TBM a purpose built steel frame was required for the TBM thrust rams to react against. The shove frame had to be able to transfer the thrust loads from the TBM shield to the ground below and thrust wall behind. A range of potential thrust loads and jacking patterns were examined to develop the design load cases for the shove frame. The shove frame was used to launch the TBM at the southern portal and to re-launch it at the northern portal. Elements of the shove frame will also be used to support the portal faces during the TBM arrivals.CITATION:Kubik, D and The, K, 2014. Waterview Connection – temporary works for tunnel boring machine?launching, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The King River Power Development on the West Coast of Tasmania has involved the storage of the waters of the King River in the new Lake Burbury and their diversion through a 7 km tunnel to a 144 MW power station. The last kilometre of this tunnel descends through 160 m under a ridge before emerging from the bank of the King River at the power station site. The decreasing cover over the tunnel as it approaches the power station meant that a steel lining was required in the last few hundred metres of the tunnel. This paper describes the geotechnical investigations which were carried out to establish the necessary length of the steel lining.

Jan 1, 1993

By U JSger

The Westerschelde tunnel will be the first permanent road link between the Dutch regions of South Beveland and South Flanders. Two tunnel tubes, each 6.6 km long, will be driven using the shield tunnelling method. The difficult ground conditions and a water pressure of up to 6.5 bar make great demands on the design. This paper describes the problems and their solutions.

Jan 1, 1999

By R Shelton

The Big Wainihinihi River and tunnel are located on the western side of the Southern Alps of New Zealand within the active Alpine Fault zone, which marks the boundary between the Pacific and Australian Tectonic Plates. The tunnel was built over 100 years ago to supply water for gold mining, but it now conveys water from a high-energy intake to a canal that supplies three of TrustPower’s hydro-electric power stations with a combined installed generating capacity of 10 MW. Part of the tunnel passes through an unstable 50° schist slope, which fi rst suffered a wedge failure in the 1929 Arthur’s Pass Earthquake and was reinstated in the mid-1970s for hydro generation. In 2008, TrustPower’s monitoring system showed that the wedge failure had remobilised and that urgent remediation was required.Harker Underground Construction (Harker) was awarded a design-build contract to restore the tunnel to service by tunnelling a new central section. Their geotechnical engineers, Peters and Cheung, reviewed the tunnel’s stability and proposed a new, safer tunnel alignment, deep behind the failure wedges. This work was based on their failure model, cost-benefit studies, and engineering geology completion mapping at the time of re-opening.Construction innovation was an important factor in ensuring the project’s success, as were detailed geological and geotechnical information, a robust methodology, strong client relationship and planning. To suit the varying rock conditions and restricted space, Harker combined a traditional drill-and-blast method with light-weight modular steel sets and timber supports to reduce construction costs and mitigate support risk. To make material handing easier in the tight conditions, a special electric locomotive was designed and built and blasting confi gurations were adapted to suit varying rock conditions in the highly fractured schist.The isolated site meant interesting and unexpected challenges, particularly communications and resources (both human and material). Despite that, the project was completed within budget, on schedule, and with no lost-time injuries.

Mar 8, 2011

By J P. Burr

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will include 2.1 km of ‘undrained’ driven tunnels, 500 m of drained cut-and-cover tunnel and tunnel portals.The project is aligned beneath a stream valley of Oakley Creek, which is incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The resulting topography, geology and hydrogeology of the tunnel alignment are complex.The Assessment of Effects required estimation of the likely settlements resulting from the tunnel construction and assessment of their effects on the buildings, services and other features. A conservative approach was taken when estimating settlements in order to provide an upper bound estimate of the consequent effects. There are three sources of these settlements: mechanical settlement from the tunnel excavation, mechanical settlement from the displacement of retaining walls and consolidation settlement from the groundwater drawdowns during construction and, in some cases, in the long-term.The settlements from these sources were calculated independently and then combined to identify the most critical effects. These combined settlements were used to assess the potential damage to the buildings, services and other features above and around the tunnels. The combined settlement results generally followed the anticipated trough shape centred on the underlying tunnel but with some noticeable effects relating to the underlying geology and hydrogeology.The effects on buildings were typically assessed as negligible with some areas of very slight to moderate damage predicted. Effects on services are anticipated to be minor but some large and older pipes will require specific monitoring during construction. A monitoring programme is proposed to allow the actual settlement and effects to be compared to those estimated with appropriate responses should those effects significantly differ.This paper describes the methods used to calculate and combine the settlements and assess their effects.

Mar 8, 2011

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

By E P. O’Dwyer

Segment and gasket lining in tunnel boring machine (TBM) tunnels; and sheet membrane lining systems in driven tunnels are robust waterproofing systems each with a proven history of performance in Australia and further afield. Where an interface between these two systems occurs, the potential for costly failures is vastly increased and additional attention to detail is required in design, planning and construction. TBM cross-passages represent the most common occurrence of this interface, with steel compression flanges and neoprene gaskets being the typical means of connecting the waterproofing systems. There is a large variance in both detailing these flanges and associated outcomes, which makes this an area where there is room for improvement within the industry.The paper will look to tease out the various issues associated with this interface and how they can be dealt with efficiently with appropriate design measures, robust planning and carefully controlled construction methods.The paper will also look to review the new technologies and systems currently being put forward as potential alternatives, including an epoxy tape system, which has recently been successfully trialled on a project in Europe under high-pressure head.CITATION:O’Dwyer, E P, 2014. The challenge of waterproofing cross passages in segmentally lined tunnel boring machine tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014